Manuals / Bacharach / Household Appliance / Smoke Alarm

Bacharach AGM300 Mounting Instructions, Screw Locations, Installation, AGM300 Mounting Specs

Models: AGM300 ADM800

1 94

Download 94 pages 38.55 Kb

Page 11

Image 11

AGM300 - Mounting Instructions

Screw Locations

The AGM300 should be installed plumb and level and securely fastened to a rigid mounting surface. The enclosure utilizes keyhole mounting brackets designed for #12 pan head fasteners. Locate the four screws as shown in the diagram and leave the screw heads protruding approximately 3/16".

AGM300 Mounting Specs

Installation

Hold the monitor flat against the mounting surface and allow it to slide down engaging the screw heads in the keyhole slots of the mounting brackets. Adjust the screws as necessary to hold the monitor securely against the mounting surface.

Instruction 3015-4275

Page 11

Image 11

Bacharach ADM800 manual AGM300 Mounting Instructions, Screw Locations, Installation, AGM300 Mounting Specs

Contents

Rev May AGM300 / ADM800 Ammonia Gas Monitoring SystemInstruction Table of Contents Please Read this Manual Carefully Before Use How to Use This ManualIntroduction Safety Precautions Altitude Limit Hazard Symbols on MonitorInstallation Category CleaningSuggested Location of Sampling Points Functional OverviewGeneral Description Communication OptionsMachine Room ChillerLED Standard Accessories for a 4 Point SystemInspection AGM300 Installation ConsiderationsLocating the Monitor AGM300 Mounting Specs InstallationAGM300 Mounting Instructions Screw LocationsInlet / Purge Ports AGM300 Connecting Air LinesOverview AGM300 Side ViewTubing Considerations Connecting Purge LineConnecting Exhaust Line Connecting Sample Intake LinesAGM300 Interior Schematic / OUT Do not Apply PowerSwitches / Fuses ON/OFFVAC Installation AGM300 Electrical WiringAGM300 AC Input Power and Ground Connections Integrating with Building Management Systems AGM300 Connecting Communication DevicesRS-485 Connector Ammonia Display Module ADM800 ConnectionOUT Changing Terminator SettingsPersonal Computer Refer to AGM300 PC Software Section RS-485 Connections Between AGM300’s Connecting to a Building Management SystemMultiple AGM’s Unit Node Terminator Outout Building Management System Programming the AGM300 Using PC SoftwareAGM300 PC Software Multiple AGM300’s Connected to a Building Management SystemTrend Data Saving the AGM300 Program to a Disk or DriveTo Open a Saved Program To Send a Saved Program to an AGM300Sealevel SYSTEMS, INC USB Type LaptopsConnection Current Loop ConnectorAGM300 Current Loop Interfaces Optional 4-20 mAdc OutputsAGM300 Relay Connector AGM300 Connecting External AlarmsTypical AGM300 Relay 1 and Relay 2 Wiring Leak Spill Evacuate FaultADM800 Oblique Photo ADM800 InstallationOverview ADM800 Installation ConsiderationsADM800 Mounting Specs ADM800 Mounting InstructionsFront Panel Chassis ADM800 Interior SchematicTo Host To MonitorsVAC Installation ADM800 Electrical WiringADM800 AC Input Power and Ground Connections Integration with Building Management System ADM800 Communication ConnectionsAGM300 Network To Monitor Changing Terminator Switch SettingsADM800 Relay Connector ADM800 Connecting External AlarmsADM800 Operation ADM800 Exterior SchematicADM800 Overview System Screen ADM800 Screen DisplaysADM800 System Programming Setup ParametersPassword Protection Clock Setup Screen ADM800 Setup ProgrammingSetting the Clock AGM Baud Rate Navigating to the 1st ADM Setup ScreenContrast Number of AGM UnitsBuilding Management System Stop Bits Audible AlarmPassword Enabling Building Management System ConnectionAGM Node Address Navigating to the 2nd ADM Setup ScreenSetting Relay Parameters ADM Setup Screen #2AGM Setup Screen #2 AGM300 Setup ProgrammingNavigating to the 1st and then 2nd AGM Setup Screen Screen #1 AGM Setup Screen #1Zone Hold Time Number of Zones InstalledAlarm Ack Mode LocationZone Change Re-Zero ModeLoop 2 Factor AutoAGM Setup #3 Screen Navigating to the 3rd AGM Setup ScreenService Timeout Distance ADM800 Zone Setup ProgrammingNavigating to the 1st Zone Setup Screen Zone Setup Screen #1Log Interval Average TemperatureNavigating To the 2nd Zone Setup Screen Current PPMEvacuation Level Re-Setting the Peak PPM ValueSpill Level Zone Screen General OperationFunctional Overview Working with the Zone ScreenZone Screen Alarm Mode Zone Screen Hold ModeFault Conditions Working with the System Screen System Screen Alarm ModeAlarm Log Screen AGM Setup #1 ScreenSystem Screen Fault Mode Alarm Summary Screen Working with AlarmsResponding To Alarms Alarm Detail Screen Alarm Detail ScreenAlarm Summary Screen Acknowledge Mode Acknowledging AlarmsTrend Screen Working with the Trend ScreenOverview Log Interval Navigating To the Trend ScreenFault Screen Working with System FaultsNavigating to the Fault Screen Critical Faults Reset to Factory Default SettingsFault Log Screen Clearing System FaultsViewing Fault Log Calibration Screen Adjusting Calibration FactorWorking with the Calibration Screen Navigating to the Calibration ScreenCalibration Procedure Diagnostic Screen Working with the Diagnostic ScreenNavigating to the Diagnostic Screen Diagnostic Screen OverviewInstruction System Screen Service Mode Service ModeInstruction Appendix Replacing Fuses AGM300 / ADM800 MaintenanceServicing Inline Filter Servicing Air LinesMA Interface Board Optional AccessoriesIntake Manifolds ADM800 Logic Diagram Modbus RTU Protocol RS-485 Communication ProtocolProtocol Details AGM300 Modbus RTU OperationKey Comm Protocol Parameters Modbus Mode RTU onlyTIM Summary of RegistersData Type Abbreviations Register Name Number Type DescriptionMinutes RS-485BAUD REVUnused TIM UnusedLSB Service mode register to change this parameterMode. do not Modify use zone hold register or MSBGood. do not Modify Zone Data Register 0x12xxh R/W 78 bytesVariable Type Length Description Instruction Instruction Stpppm To Release the Zone Hold Use the Following Sequence of Steps Variable Type Length Description Fault Log Register Register 0x1900, 0x1901h BytesInstruction Last 100 log points 2 byes per point Point to current readingTime record for each of the 100 log points. The format Service Warranty and ServiceWarranty Field Repair Return ProcedureProducts Covered under Warranty and Service Policy AGM300 Specifications ADM800 Specifications Instruction Headquarters Hunt Valley Circle, New Kensington, PA