Manuals / Barco / Computer Equipment / Projector

Barco R9040100 What will be indicate ?, Service Mode, Start Up, Available items, software version

Models: R9040111 R9040101 R9040100 R9040110

1 82

Download 82 pages 3.45 Kb

Page 69

-software version

Service Mode

Start Up

1Push the cursor key  or  to highlight 'Title Page' (menu 1).

2Press Enter to select.

The Title page will be displayed.

IDENTIFICATION

TITLE PAGE

SIM OPTIONS

Select with  or 

then <ENTER> <EXIT> to return.

menu 1

Available items

BARCO

REALITY SIM6

Proj. address : 001 Soft. version : 1.0 Config : front/

ceiling

Baudrate PC : 9600

text : ON

Serial no.: 1010200

Run time : 100 h

Select with  or 

then <ENTER> <EXIT> to return.

menu 2

-type of projector : BARCOREALITY SIM6

-software version

-Proj. Address : to change the address of the projector, see Change Projector Address in this chapter.

-Installation : possible installations :

*Front/Ceiling

*Front/Table

*Rear/Ceiling

*Rear/Table

To change the installation configuration follow the instructions in chapter Installation Guidelines.

-Baud rate : transfer speed for communication with an IBM PC (or compatible) or MAC. The baud rate of the projector must be the same as the baud rate of the connected computer. When there is a difference, consult 'Change Baudrate PC' in this chapter.

-Projector Run Time : gives the total run time since the first start up. All projectors leave the factory with a run time of approximately 24 hours.

-Projector Serial number : indicates the fabrication number of the projector. This number can be useful when calling for technical assistance.

SIM Options

What will be indicate ?

This menu will indicate if the SIM options are installed or not.

Start Up

1Push the cursor key  or  to

2Press Enter to select.

The SIM options screen will be

highlight 'SIM Options' (menu 1).

displayed (menu 2).

IDENTIFICATION

TITLE PAGE

SIM OPTIONS

Select with  or 

then <ENTER> <EXIT> to return.

SIM OPTIONS

SOFT EDGE: ON

TDR : ON

TMR : ON

UNIFORMITY : ON MOT. DIMMING : ON

<EXIT> to return.

menu 1

menu 2

Available SIM options

-Soft Edge

-TDR : transportation delay reduction

-TMR : true motion reproduction

-Uniformity

-Motorized Dimming

5976069 BARCOREALITY SIM6 21032000		9-3

Image 69

Barco R9040100, R9040110, R9040101 What will be indicate ?, Service Mode, Start Up, Available items, software version

Contents

OWNERS MANUAL BARCO PROJECTION SYSTEMSREALITY SIM R9040100 - R9040101 R9040110 - R9040111 Federal communication commission FCC statement BARCO n.v./Projection SystemsNoordlaan B-8520 Kuurne Belgium Tel +32/56/368211 Fax +32/56/351651 E-mail sales.bsp@barco.comTable of Contents TABLE OF CONTENTSPACKAGING AND DIMENSIONS INSTALLATION GUIDELINESSTART UP OF THE ADJUSTMENT MODE GETTING STARTEDTable of Contents Table of Contents RANDOM ACCESS ADJUSTMENT MODEPassword Protection Entering the PasswordTable of Contents SERVICE MODE INSTALLATION MODE7-22 Table of ContentsSTANDARD SOURCE SET UP FILES SOURCE NUMBERS 81 - 86 AND 91Table of Contents Packaging and Dimensions 1 PACKAGING AND DIMENSIONSContents of the complete unit box Projector PackagingDimensions Projector CasePackaging and Dimensions Installation Guidelines 2 INSTALLATION GUIDELINESSafety warning Installation GuidelinesWhich configuration can be used ? Projector ConfigurationsPositioning the Projector Installation GuidelinesWhich lens has to be selected LensesAvailable lenses Installation GuidelinesHow to install the lens? Lens formulas to calculate the projector distanceInstallation Guidelines Battery installation in the RCU Cleaning the LensHow to replace the batteries in the RCU ? Inserting the BatteriesNote, only important if more than one projector is installed in the room Installation GuidelinesAC Power mains cord connection Power connection to ProjectorSwitching on 4 CONNECTIONSLamp Run Time Switching to Stand-byLamp Run Time Warning ConnectionsSwitching to Stand-by Warning Switching OffSet up of the input selection Input Source ConnectionHow to select input Slot Which signals can be connected to the 5-cable inputConfiguration of the 5-cable input 5-cable Input Slot slotNote for RCVDS05 users Pin configuration of the D15 connectorAudio connection optional Computer input/Monitor output²Video Input Optional How to select SlotWhat can be connected S-Video Input optionalSerial Digital Input / Serial Digital Output optional Pin configuration mini DIN plugWhat can be connected to this input ? IEEE 1394 InputConfigurations of the port Set up of the Baud Rate for Communication with a ComputerConnecting a RCVDS 05 to the projector RS232 ConnectionHow to activate ? When available ?What is available ? How to lock an audio input ?Connections 4-105976135 BARCOSIM 6 Remote control Remote Control & Local Keypad5 GETTING STARTED Getting StartedSwitching on Operating the ProjectorAttention Switching to Stand-by Getting StartedQuick Lens Adjustment Quick Set Up AdjustmentsSwitching to Stand-by Switching OffQuick On Screen Color change Getting StartedOSD COLOR Hardwired Remote Input Using the RCUPointing to the reflective screen Directly to one of the IR sensors of the projectorSet up an Individual Projector Address Why a projector address ?How to control the projector or projectors Before using the RCUPicture controls Controlling the ProjectorSound Controls optional Phase ControlThe Selection key The Pause keyVolume Control Getting StartedStart up of the Adjustment Mode 6 START UP OF THE ADJUSTMENT MODEAdjustment Mode PasswordProtectionRemark Setting up your own passwordStart up of the Adjustment Mode Error7 RANDOM ACCESS ADJUSTMENT MODE Random Access Adjustment ModeRandom Access Mode Connecting a new Source Picture ServiceStart up the File Service Starting UpThe image is not perfect ? How to load a file ?What can be done with the Edit File menu ? Random Access Adjustment ModeWhich items can be adjusted ? How to start up the Edit menu ?How to change the settings ? How to find the correct values for the displayed item?Sync pulse Clamp pulse Clamp width Clamp delay Random Access Adjustment ModeRead AMDS OptionsRename a file Random Access Adjustment ModeStart Up Field PolarityRandom Access Adjustment Mode How to change the characters ?How to change the characters ? Copy a fileRandom Access Adjustment Mode File SortDelete Start UpWhat is CTI ? Picture TuningHow to change thet CTI settings What is motion compensation ?LCD speed How to start up ?LCD speed R/G LCD speed B/GAdjusting the Color Temperature Available Color TemperatureRandom Access Adjustment Mode Color TemperatureHow to change the gamma value ? What can be adjusted ?What can be done ? How can it be selected ?How to adjust the input balance ? Why adjusting the input balance ?To change the Color depth value To change the black colorHow to adjust ? Audio TuningAvailable items Random Access Adjustment ModeHow to set up the fade ? How to stop sound reproduction ?How to install the sound mode ? Random Access Adjustment ModeWhich Geometry adjustments are possible ? How to lock input source to an audio source ?How can an adjustment be adjusted ? GeometryTo start up the shift action To start up the size adjustmentRandom Access Adjustment Mode What can be done ?Aligning the keystone Available Blanking AdjustmentsRandom Access Adjustment Mode What can be done ?How to setup the desired aspect ratio ? Adjusting the blankingRandom Access Adjustment Mode Aspect Ratio 54/43/169Soft Edge How to change the geometry options ?To start up the Soft Edge function Which soft edge items are available ?Available image processing features How to set up the width ?How to start up the Demo ? Available soft edge typesHow to start up ? Random Access Adjustment ModeSplit Screen PurposeInstallation Mode 8 INSTALLATION MODEInstallation Mode To view or to change the input configurationPossible results for the input slots What if a switcher is connected to the projector ?800 Peripheral Defining the Output module of the RCVDS05Set up the Correct Configuration ConfigurationHow to change this color setting ? OSD color On-Screen DisplayNo Signal How to select an internal pattern ?Changing the shutdown setting Available patternsHow to program the quick access keys function keys Quick Access KeysGetting an overview Factory preprogrammed keysZoom/Focus/Shift Lens AdjustmentsInstallation Mode What can be done ?Menu Position How to change the setting ?Installation Mode What can be done ?5976135 BARCOREALITY SIM6 Installation ModeService Mode 9 SERVICE MODEService Mode Built-up of the service modeWhat can be seen ? IdentificationWhat will be indicated on the title page ? Service ModeService Mode What will be indicate ?Start Up Available itemsHow to enable or disable the password function ? Change PasswordHow to change the password ? Change LanguageHow to change that common address ? How to change that address ?Start up Entering the new projector addressWhen is it allowed ? Reset Lamp RuntimeChange Baudrate PC Lamp Run Time HistoryService Mode DimmingStart Up What can be done ?Available settings How to add the BARCO logo or to change a setting ?Service Mode Start UpUniformity Panel AdjustmentsService Mode PANEL ADJUSTMENTSI2C diagnosis Preset Input BalanceService Mode Start UpAppendix A Standard Source Set Up Files A STANDARD SOURCE SET UP FILESAppendix A Standard Source Set Up Files Appendix A Standard Source Set Up Files 5976135 BARCOREALITY SIM6 Appendix A Standard Source Set Up FilesSource Numbers 80 - 89 and 90 B SOURCE NUMBERS 81 - 86 AND 91Projector without any 800 peripheral connected Projector with a 800 peripheral connectedSource Numbers 80 - 89 and 90 Source numbers 81