Manuals / Barnett Engineering / Household Appliance / Home Security System

Barnett Engineering ARU CV2 instruction manual directory menu. The choices at this point are

Models: ARU CV2

1 44

Download 44 pages 18.61 Kb

Page 35

Voice Storage and Configuration with the Telset

4-2

directory menu. The choices at this point are:

0UU - Speak the Directory Codes

These codes correspond to buttons found in the Directory Editor dialog box used for PC programming. They are used to enter the new configuration.

#0	DIAL	Initiate a phone call
#1	WAIT	Measured in seconds with a maximum value of 255
#2	AUTO ACK
#3	DTMF	Send the a DTMF string
#4	ALERT	Send the alert signal
#5	ANSWER	Wait for answer detection before speaking
#6	VOICE	Speak the stored voice messages
#7	SIGNAL	Send the DTMF string entered in Points - no voice
#8	‘!’	Two second delay used in dial or DTMF strings
##	‘#’ Char	Used to enter the ‘#’ character in a dial or DTMF string
UU	OK	Accept or end of sequence

1UU ... 6UU - Select the required directory

When a directory is selected the Cv2 speaks the current settings for the first line in the directory in this manner:

Cv2: “Directory One Line One is DIAL 2559544 WAIT 3 VOICE”

This setting can be accepted or edited according to these commands available in the directory sub-menu:

2UU Change current entry

Cv2: “beep”

To change the directory line, a complete sequence of codes and values for the line must be entered. The codes defining the activities are those shown previously as Directory Codes. A maximum of 250 keystrokes can be entered. For example, if the setting for line 1 in directory 1 was to be changed so that the wait time was 5 seconds instead of 3, the entry would be:

#0 2559544 #1 5 #6 UU

which would be the same as [DIAL]2559544 [WAIT]5 [VOICE] in the PC programming. When the Cv2 detects the UU at the end of the entry, it speaks the new entry.

Cv2: “Directory One Line One is DIAL 2559544 WAIT 5 VOICE”

You can either accept the new entry (UU), repeat the change command (2UU) or use either the delete (3UU) or insert (4UU) functions.

If an invalid keystroke is detected in the sequence, the Cv2 will speak the line as entered with the word “Error” at the end.

B1272M001

BARNETT ENGINEERING LTD.

ProTalk Cv2

Image 35

Barnett Engineering ARU CV2 instruction manual directory menu. The choices at this point are

Contents

HOOXODU $58 Manual Revision 7 - July3UR7DON 5.Specifications 2.Installation3.Configuration with the PC 4.Voice Storage and Configuration with the Telset1.1 Cv2 Capabilities 1.2 What constitutes an alarm?1. Operations Overview POINTS UP TO 30 INPUTS OR OUTPUTS 1.3 How are alarms processed?8 INPUTS HARDWARE INPUTS 8 OUTPUTS HARDWARE OUTPUTSProTalk Cv2 1.DIAL2458829 VOICEOperations Overview B1272M0011.DIAL2458829 ALERT VOICE 1.5 How do you want to respond to an alarm call?1.DIAL2458829 VOICE 2.DIAL2336700 VOICE 3.DIAL9842121 VOICE 4.DIAL9843316 VOICEB1272M001 1.6 What if an alarm is not acknowledged?1.8 Sending remote control commands Operations OverviewDoes the cell phone work? 1.9 Indicators1.10Troubleshooting Is there power to the unit?Operations Overview Are the inputs connected properly?The unit does not dial out I cannot call into the unit2.2 Mounting 2 Installation2.1 Antenna requirements 2.2.2 Stand-alonemodel 2.3 Input port connectionsLow” 2.3.1 Ground closure alarm signalFigure 6 +5 VDC Input Wiring 2.3.2 +12 volt alarm signal2.3.3 +5 volt alarm signal Figure 5 +12 Volt Input WiringB1272M001 2.5 Configuration programming connection2.4 Output port connections InstallationProTalk Cv2 InstallationFigure 11 Stand-aloneCv2 Figure 12 Packaged Cv2 B1272M0013.1 PC requirements 3 Configuration using the PC3.2Installing the program 3.3 Starting the configuration program3.4.4 Groups 3.4.1 File Operations3.4.2 Hardware 3.4.3 General3.5.1 Hardware section 3.5 Configuring the Cv23.4.6 Directories 3.4.7 ProgrammingTotalizer Input Watchdog InputInterval Input Timed Output Configuration using the PCAnalog Input On/Off OutputPoint Name Common Settings for Points I/O Port SelectionUsing Group DTMF Tag EnabledAlarm State Digital and Watchdog PointsClear Code PrefixUnit SuffixDecimal Values Configuration using the PCCalibrate Binary ValuesDTMF On Code HysteresisUnits On/Off Output PointDTMF On Code Configuration using the PCDTMF Off Code Timed Output PointAcknowledge Code Enable This GroupEnable Auto Ack Group NameLong Timer Enable Ack RequestTimers Short TimerAcknowledge Received Alarm ActiveNew Alarm Special Function OutputsWait 3.5.4 DirectoriesDial Voice Auto AckDTMF AlertDelete LevelSignal Access CodeCall Progress 3.5.6 Configuration ProgrammingShift Change Code Temporary Acknowledge TimeVocabulary Configuration DataVoice Messages 4.3 Commands 4 Voice Storage and Configuration with the Telset4.1 Setup 4.2 Accessdirectory menu. The choices at this point are 3UU Delete current entry Cv2 “beep” Cv2 “Site ID is Ajax Compressor Station”Cv2 “Group One is Electrical” Cv2 “Electrical ON” or “Electrical OFF.”4.4 Telset Programming Summary Cv2 Site ID is Ajax Compressor Station Exit ExitEdit Directories Record Sites and GroupsRecord Points Enable GroupsExit You MechanicalCv2 Code Five is Two Three Eight Query NAMCv2 Code Four is One or Code Four is Two Query MIN5.1 General 5 Specifications5.2 Programmable Features 5.4 Options 5.3 Telephone6 Warranty