Manuals / Barnett Engineering / Household Appliance / Home Security System

Barnett Engineering ARU CV2 instruction manual Configuration using the PC, PC requirements

Models: ARU CV2

1 44

Download 44 pages 18.61 Kb

Page 15

Configuration using the PC

3-1

3 Configuration using the PC

This chapter describes how to install the programming software and configure the operation of the Cv2. When the configuration is complete, it can be viewed through the Summary command found on the File pull-down menu. In the summary, Warnings should be checked to ensure that there are no improper settings in the configuration before it is transferred to the Cv2.

3.1 PC requirements

The minimum requirements for the PC used to run the Cv2 programming software are:

•386 processor

•Windows 95

•8M RAM

•SVGA screen

•Serial COM port

3.2Installing the program

The program diskettes supplied with the Cv2 contain the configuration software and the software installation utility. Place disk 1 into the floppy drive and select the program SETUP.EXE using Run in the windows Start menu. Follow the instructions and the installation program will automatically install the configuration program onto the hard drive.

3.3 Starting the configuration program

To start the program, click on the Cv2 icon that appears in the installed location. The program will load and search for the default startup files:

Cv2.dat - the configuration database

Cv2.cfg - the serial port setting

If these files are not found, default files will be created and a warning posted.

3.4 The desktop and how to access programming functions

At the top of the desktop are drop-down menus and buttons on the taskbar that launch the various operations in the program. The taskbar buttons duplicate the operations found in the menu. To activate on-line help, press F1 or select the Help menu at the top of the desktop. Context help for the controls is available when dialog boxes are open. Press the Help question mark in the upper right of the dialog box, place the curser with the question mark over the control, then click the left mouse button.

The menu and button operations are summarized in the following section.

B1272M001

BARNETT ENGINEERING LTD.

ProTalk Cv2

Image 15

Barnett Engineering ARU CV2 instruction manual Configuration using the PC, PC requirements, 3.2Installing the program

Contents

Manual Revision 7 - July 3UR7DONHOOXODU $58 5.Specifications 2.Installation3.Configuration with the PC 4.Voice Storage and Configuration with the Telset1.2 What constitutes an alarm? 1. Operations Overview1.1 Cv2 Capabilities POINTS UP TO 30 INPUTS OR OUTPUTS 1.3 How are alarms processed?8 INPUTS HARDWARE INPUTS 8 OUTPUTS HARDWARE OUTPUTSProTalk Cv2 1.DIAL2458829 VOICEOperations Overview B1272M0011.DIAL2458829 ALERT VOICE 1.5 How do you want to respond to an alarm call?1.DIAL2458829 VOICE 2.DIAL2336700 VOICE 3.DIAL9842121 VOICE 4.DIAL9843316 VOICEB1272M001 1.6 What if an alarm is not acknowledged?1.8 Sending remote control commands Operations OverviewDoes the cell phone work? 1.9 Indicators1.10Troubleshooting Is there power to the unit?Operations Overview Are the inputs connected properly?The unit does not dial out I cannot call into the unit2 Installation 2.1 Antenna requirements2.2 Mounting 2.2.2 Stand-alonemodel 2.3 Input port connectionsLow” 2.3.1 Ground closure alarm signalFigure 6 +5 VDC Input Wiring 2.3.2 +12 volt alarm signal2.3.3 +5 volt alarm signal Figure 5 +12 Volt Input WiringB1272M001 2.5 Configuration programming connection2.4 Output port connections InstallationProTalk Cv2 InstallationFigure 11 Stand-aloneCv2 Figure 12 Packaged Cv2 B1272M0013.1 PC requirements 3 Configuration using the PC3.2Installing the program 3.3 Starting the configuration program3.4.4 Groups 3.4.1 File Operations3.4.2 Hardware 3.4.3 General3.5.1 Hardware section 3.5 Configuring the Cv23.4.6 Directories 3.4.7 ProgrammingWatchdog Input Interval InputTotalizer Input Timed Output Configuration using the PCAnalog Input On/Off OutputCommon Settings for Points I/O Port Selection Using GroupPoint Name DTMF Tag EnabledAlarm State Digital and Watchdog PointsClear Code PrefixUnit SuffixDecimal Values Configuration using the PCCalibrate Binary ValuesDTMF On Code HysteresisUnits On/Off Output PointDTMF On Code Configuration using the PCDTMF Off Code Timed Output PointAcknowledge Code Enable This GroupEnable Auto Ack Group NameLong Timer Enable Ack RequestTimers Short TimerAcknowledge Received Alarm ActiveNew Alarm Special Function Outputs3.5.4 Directories DialWait Voice Auto AckDTMF AlertDelete LevelSignal Access CodeCall Progress 3.5.6 Configuration ProgrammingShift Change Code Temporary Acknowledge TimeConfiguration Data Voice MessagesVocabulary 4.3 Commands 4 Voice Storage and Configuration with the Telset4.1 Setup 4.2 Accessdirectory menu. The choices at this point are 3UU Delete current entry Cv2 “beep” Cv2 “Site ID is Ajax Compressor Station”Cv2 “Group One is Electrical” Cv2 “Electrical ON” or “Electrical OFF.”4.4 Telset Programming Summary Cv2 Site ID is Ajax Compressor Station Exit ExitEdit Directories Record Sites and GroupsRecord Points Enable GroupsExit You MechanicalCv2 Code Five is Two Three Eight Query NAMCv2 Code Four is One or Code Four is Two Query MIN5 Specifications 5.2 Programmable Features5.1 General 5.4 Options 5.3 Telephone6 Warranty