Manuals / Belshaw Brothers / Kitchen Appliance / Microwave Oven

Belshaw Brothers TG 50 manual Remove the upper air duct panel, Remove the lower air duct panel

Models: TG 50

1 64

Download 64 pages 27.72 Kb

Page 18

Image 18

21. Remove the upper air duct panel

22.Lift up on the outside end of the lower air duct panel.

23. Remove the lower air duct panel.

24. Remove the oven crumb tray

25. Oven with all parts removed.

26.Insert flat tip screwdriver into finger assembly if it cannot be removed by hand.

Belshaw Bros., Inc. • 1750 22nd Ave. S. • Seattle, WA 98144 • Phone 206-322-5474 • Fax 206-322-5425

MN-1716EN

Thermoglaze 50

Page 18

Image 18

Belshaw Brothers TG 50 Remove the upper air duct panel, Lift up on the outside end of the lower air duct panel, MN-1716EN

Contents

1750 22nd Avenue South Seattle, WA Phone 206 322-5474 Fax 206 Operator’s ManualFor Serial Number W04060001 on Belshaw Bros., Inc Toll FreePage EQUIPMENT RECORD 0805 MN-1716EN Belshaw Bros., Inc 1750 22nd Avenue South Seattle, WAPhone 206 322-5474 Fax 206 Toll Free Page MN-1716EN ContentsThermoglaze InstallationPreface 1 Unloading and Uncrating DO NOT LIFT EXCESSIVE WEIGHTIdentification2 MN-1716ENThermoglaze 08/19/05 Venting Installation3Electrical Building LayoutsAssembly4 Clean all parts with mild soap and water andOptional Figure 4-2 Infeed - Left hand viewFigure 4-3 Swing away glaze trough Figure 4-4 Right Hand ViewThermoglaze Figure 4-5 Control Panel ViewFigure 4-6 Thermoglaze System MN-1716ENOperation5 Cleaning6 Daily TG Cleaning InstructionsDisassembly 9. Remove the conveyor assembly through the outfeed end of the oven 15. Lift up on the outfeed lower finger assembly and remove it 23. Remove the lower air duct panel 21. Remove the upper air duct panel22. Lift up on the outside end of the lower air duct panel 24. Remove the oven crumb tray 25. Oven with all parts removed30. Remove the lower glaze hose clamp and gasket 27. Remove the finger cover 28. Remove the columnating plate29. Loosen the lower glaze hose clamp 31. Remove the upper pump clamp36. Remove the glaze pump cover and “O” ring 33. Remove the glaze reservoir and hose 34. Remove the drip pan35. Remove unscrew the 4 glaze pump cover wing nuts 37. Remove the glaze pump bodyThermoglaze 39. Remove the pump body and impellers40. Remove the impellers from the pump body MN-1716ENCleaning Assembly8. Install the upper clamp 5. Install the 4 wing nuts finger tight7. Install the drip pan and glaze reservoir 9. Install the lower gasket, hose and clamp14. Install the upper air panel assembly 11. Install the finger covers 12. Install the oven crumb tray13. Install the lower air duct panel 15. Install the lower infeed finger assembly18. Install the lower outfeed finger assembly 28. Set the heat shield on top of the oven 24. Install the glaze reservoir cover 25. Glaze reservoir installed26. Install the glaze drain tray 27. Connect the drive belt MN-1716EN29. Slide the heat shield over the oven ThermoglazeMN-1716EN Maintenance7 Troubleshooting8 GLAZE IS MISSING THE DONUTS ON ONE SIDE OF THE GLAZE SCREEN CONVEYOR WILL NOT MOVEGLAZER WILL NOT PUMP GLAZE Possible CausesPossible Causes THE PUMP MOTOR WILL NOT RUNTHE FILL HOSE IS LEAKING What To DoSpeed control/cook time adjustment Temperature AdjustmentAppendix9 TNG-2011. THERMOGLAZE ASSEMBLY MN-1716ENThermoglaze TNG-2011. THERMOGLAZE ASSEMBLY ThermoglazeMN-1716EN TNG-2011. THERMOGLAZE ASSEMBLY MN-1716ENThermoglaze TNG-2011. THERMOGLAZE ASSEMBLY ThermoglazeMN-1716EN TNG-2011. THERMOGLAZE ASSEMBLY MN-1716ENThermoglaze Thermoglaze MN-1716ENMN-1716EN ThermoglazeThermoglaze MN-1716ENMN-1716EN ThermoglazeThermoglaze MN-1716ENMN-1716EN THERMOGLAZESK-1258 R5 ThermoglazeIMPINGER CTI TROUBLESHOOTING GUIDESYMPTOM POSSIBLE CAUSEOven will not heat Conveyor speed Conveyor will not runS/N 4000480 and Below varying or intermittentConveyor speed Conveyor will not runS/N 3000481 & Above varying or intermittentPOTENTIOMETER, TEMPERATURE CONTROL REMOVAL, INSTALLATION, AND ADJUSTMENTSWITCH, ON-OFF MODEL SERIESAIR PRESSURE SWITCH - ADJUSTMENT AIR PRESSURE SWITCH - REPLACEMENTADJUSTMENT SCREW THERMOSTAT, OVEN CAVITY HI-LIMITRELAY CONTACTOR TIME DELAY RELAYMAIN FAN RELAY TRANSFORMER - CONVEYORELECTRONIC TEMPERATURE CONTROL BOARD - REPLACEMENT ASSEMBLY OF MAGNET TO MOTORCONVEYOR CONTROL BOARD - REPLACEMENT ELECTRONIC TEMPERATURE CONTROL - CALIBRATIONCONTROLBOARD TEMPERATUREAIR SWITCH HI-LIMITCAPACITOR, MOTOR OVEN BACK ASSEMBLYCOOLING FAN, CONTROL BOX CAUTION DISCHARGE CAPACITOR BEFORE REMOVINGJ U N C T I O N T E M P E R A T U R E THERMOCOUPLEINFORMATION O V E N T E M P E R A T U R EPART# PART#PART# PART#GENERAL - 1300 SERIES LETTERDESCRIPTION GENERAL - 1300 SERIES PARTS BLOW-UP NovemberCOUNTER TOP IMPINGER CONTROL COMPARTMENT - 1300 SERIES LETTERDESCRIPTION CONTROL COMPARTMENT - 1300 SERIES BLOW - UP NovemberCOUNTER TOP IMPINGER BACK - 1300 SERIES LETTERDESCRIPTION BACK - 1300 SERIES BLOW - UP NovemberCOUNTER TOP IMPINGER STANDARD CONVEYOR - 1300 SERIES LETTERDESCRIPTION EXTENDED CONVEYOR - 1300 SERIES LETTERDESCRIPTION