Manuals / Belshaw Brothers / Kitchen Appliance / Microwave Oven

Belshaw Brothers TG 50 manual Cleaning6, Daily TG Cleaning Instructions, Disassembly

Models: TG 50

1 64

Download 64 pages 27.72 Kb

Page 15

Image 15

Cleaning6

Daily TG Cleaning

Instructions

Disassembly

1.Allow the Thermoglaze to completely cool. (All material must under 130º)

2.Pump the unused glaze back into a bucket.

3.Disconnect the TG from power!

4.Remove the glaze trough.

5. Remove the drive belt.

6. Remove the glazer drain tray.

7. Remove the oven heat shield.

8. Disconnect the conveyor drive coupling.

Belshaw Bros., Inc. • 1750 22nd Ave. S. • Seattle, WA 98144 • Phone 206-322-5474 • Fax 206-322-5425

Thermoglaze

MN-544EN

Page 15

Image 15

Belshaw Brothers TG 50 manual Cleaning6, Daily TG Cleaning Instructions, Disassembly

Contents

Toll Free Operator’s ManualFor Serial Number W04060001 on Belshaw Bros., Inc 1750 22nd Avenue South Seattle, WA Phone 206 322-5474 Fax 206Page EQUIPMENT RECORD 0805 MN-1716EN Belshaw Bros., Inc 1750 22nd Avenue South Seattle, WAPhone 206 322-5474 Fax 206 Toll Free Page Installation ContentsThermoglaze MN-1716ENPreface DO NOT LIFT EXCESSIVE WEIGHT 1 Unloading and UncratingIdentification2 MN-1716ENThermoglaze 08/19/05 Building Layouts Installation3Electrical VentingClean all parts with mild soap and water and Assembly4Figure 4-4 Right Hand View Figure 4-2 Infeed - Left hand viewFigure 4-3 Swing away glaze trough OptionalMN-1716EN Figure 4-5 Control Panel ViewFigure 4-6 Thermoglaze System ThermoglazeOperation5 Cleaning6 Daily TG Cleaning InstructionsDisassembly 9. Remove the conveyor assembly through the outfeed end of the oven 15. Lift up on the outfeed lower finger assembly and remove it 24. Remove the oven crumb tray 25. Oven with all parts removed 21. Remove the upper air duct panel22. Lift up on the outside end of the lower air duct panel 23. Remove the lower air duct panel31. Remove the upper pump clamp 27. Remove the finger cover 28. Remove the columnating plate29. Loosen the lower glaze hose clamp 30. Remove the lower glaze hose clamp and gasket37. Remove the glaze pump body 33. Remove the glaze reservoir and hose 34. Remove the drip pan35. Remove unscrew the 4 glaze pump cover wing nuts 36. Remove the glaze pump cover and “O” ringMN-1716EN 39. Remove the pump body and impellers40. Remove the impellers from the pump body ThermoglazeAssembly Cleaning9. Install the lower gasket, hose and clamp 5. Install the 4 wing nuts finger tight7. Install the drip pan and glaze reservoir 8. Install the upper clamp15. Install the lower infeed finger assembly 11. Install the finger covers 12. Install the oven crumb tray13. Install the lower air duct panel 14. Install the upper air panel assembly18. Install the lower outfeed finger assembly MN-1716EN 24. Install the glaze reservoir cover 25. Glaze reservoir installed26. Install the glaze drain tray 27. Connect the drive belt 28. Set the heat shield on top of the oven29. Slide the heat shield over the oven ThermoglazeMN-1716EN Maintenance7 Troubleshooting8 Possible Causes CONVEYOR WILL NOT MOVEGLAZER WILL NOT PUMP GLAZE GLAZE IS MISSING THE DONUTS ON ONE SIDE OF THE GLAZE SCREENWhat To Do THE PUMP MOTOR WILL NOT RUNTHE FILL HOSE IS LEAKING Possible CausesTemperature Adjustment Speed control/cook time adjustmentAppendix9 TNG-2011. THERMOGLAZE ASSEMBLY MN-1716ENThermoglaze TNG-2011. THERMOGLAZE ASSEMBLY ThermoglazeMN-1716EN TNG-2011. THERMOGLAZE ASSEMBLY MN-1716ENThermoglaze TNG-2011. THERMOGLAZE ASSEMBLY ThermoglazeMN-1716EN TNG-2011. THERMOGLAZE ASSEMBLY MN-1716ENThermoglaze MN-1716EN ThermoglazeThermoglaze MN-1716ENMN-1716EN ThermoglazeThermoglaze MN-1716ENMN-1716EN ThermoglazeThermoglaze THERMOGLAZESK-1258 R5 MN-1716ENPOSSIBLE CAUSE TROUBLESHOOTING GUIDESYMPTOM IMPINGER CTIOven will not heat varying or intermittent Conveyor will not runS/N 4000480 and Below Conveyor speedvarying or intermittent Conveyor will not runS/N 3000481 & Above Conveyor speedMODEL SERIES REMOVAL, INSTALLATION, AND ADJUSTMENTSWITCH, ON-OFF POTENTIOMETER, TEMPERATURE CONTROLTHERMOSTAT, OVEN CAVITY HI-LIMIT AIR PRESSURE SWITCH - REPLACEMENTADJUSTMENT SCREW AIR PRESSURE SWITCH - ADJUSTMENTTRANSFORMER - CONVEYOR TIME DELAY RELAYMAIN FAN RELAY RELAY CONTACTORELECTRONIC TEMPERATURE CONTROL - CALIBRATION ASSEMBLY OF MAGNET TO MOTORCONVEYOR CONTROL BOARD - REPLACEMENT ELECTRONIC TEMPERATURE CONTROL BOARD - REPLACEMENTHI-LIMIT TEMPERATUREAIR SWITCH CONTROLBOARDCAUTION DISCHARGE CAPACITOR BEFORE REMOVING OVEN BACK ASSEMBLYCOOLING FAN, CONTROL BOX CAPACITOR, MOTORO V E N T E M P E R A T U R E THERMOCOUPLEINFORMATION J U N C T I O N T E M P E R A T U R EPART# PART#PART# PART#GENERAL - 1300 SERIES LETTERDESCRIPTION GENERAL - 1300 SERIES PARTS BLOW-UP NovemberCOUNTER TOP IMPINGER CONTROL COMPARTMENT - 1300 SERIES LETTERDESCRIPTION CONTROL COMPARTMENT - 1300 SERIES BLOW - UP NovemberCOUNTER TOP IMPINGER BACK - 1300 SERIES LETTERDESCRIPTION BACK - 1300 SERIES BLOW - UP NovemberCOUNTER TOP IMPINGER STANDARD CONVEYOR - 1300 SERIES LETTERDESCRIPTION EXTENDED CONVEYOR - 1300 SERIES LETTERDESCRIPTION