Manuals / Belshaw Brothers / Kitchen Appliance / Microwave Oven

Belshaw Brothers TG 50 manual Install the finger covers 12. Install the oven crumb tray, MN-1716EN

Models: TG 50

1 64

Download 64 pages 27.72 Kb

Page 24

Image 24

11. Install the finger covers.

12. Install the oven crumb tray.

13. Install the lower air duct panel.

14. Install the upper air panel assembly.

15. Install the lower infeed finger assembly.

16.Install the upper infeed finger assembly by slipping it over the duct on the back of the oven.

Belshaw Bros., Inc. • 1750 22nd Ave. S. • Seattle, WA 98144 • Phone 206-322-5474 • Fax 206-322-5425

MN-1716EN

Thermoglaze 50

Page 24

Image 24

Belshaw Brothers TG 50 manual Install the finger covers 12. Install the oven crumb tray, Install the lower air duct panel

Contents

Operator’s Manual For Serial Number W04060001 on Belshaw Bros., Inc1750 22nd Avenue South Seattle, WA Phone 206 322-5474 Fax 206 Toll FreePage EQUIPMENT RECORD 0805 MN-1716EN Belshaw Bros., Inc 1750 22nd Avenue South Seattle, WAPhone 206 322-5474 Fax 206 Toll Free Page Contents ThermoglazeMN-1716EN InstallationPreface 1 Unloading and Uncrating DO NOT LIFT EXCESSIVE WEIGHTIdentification2 MN-1716ENThermoglaze 08/19/05 Installation3 ElectricalVenting Building LayoutsAssembly4 Clean all parts with mild soap and water andFigure 4-2 Infeed - Left hand view Figure 4-3 Swing away glaze troughOptional Figure 4-4 Right Hand ViewFigure 4-5 Control Panel View Figure 4-6 Thermoglaze SystemThermoglaze MN-1716ENOperation5 Cleaning6 Daily TG Cleaning InstructionsDisassembly 9. Remove the conveyor assembly through the outfeed end of the oven 15. Lift up on the outfeed lower finger assembly and remove it 21. Remove the upper air duct panel 22. Lift up on the outside end of the lower air duct panel23. Remove the lower air duct panel 24. Remove the oven crumb tray 25. Oven with all parts removed27. Remove the finger cover 28. Remove the columnating plate 29. Loosen the lower glaze hose clamp30. Remove the lower glaze hose clamp and gasket 31. Remove the upper pump clamp33. Remove the glaze reservoir and hose 34. Remove the drip pan 35. Remove unscrew the 4 glaze pump cover wing nuts36. Remove the glaze pump cover and “O” ring 37. Remove the glaze pump body39. Remove the pump body and impellers 40. Remove the impellers from the pump bodyThermoglaze MN-1716ENCleaning Assembly5. Install the 4 wing nuts finger tight 7. Install the drip pan and glaze reservoir8. Install the upper clamp 9. Install the lower gasket, hose and clamp11. Install the finger covers 12. Install the oven crumb tray 13. Install the lower air duct panel14. Install the upper air panel assembly 15. Install the lower infeed finger assembly18. Install the lower outfeed finger assembly 24. Install the glaze reservoir cover 25. Glaze reservoir installed 26. Install the glaze drain tray 27. Connect the drive belt28. Set the heat shield on top of the oven MN-1716EN29. Slide the heat shield over the oven ThermoglazeMN-1716EN Maintenance7 Troubleshooting8 CONVEYOR WILL NOT MOVE GLAZER WILL NOT PUMP GLAZEGLAZE IS MISSING THE DONUTS ON ONE SIDE OF THE GLAZE SCREEN Possible CausesTHE PUMP MOTOR WILL NOT RUN THE FILL HOSE IS LEAKINGPossible Causes What To DoSpeed control/cook time adjustment Temperature AdjustmentAppendix9 TNG-2011. THERMOGLAZE ASSEMBLY MN-1716ENThermoglaze TNG-2011. THERMOGLAZE ASSEMBLY ThermoglazeMN-1716EN TNG-2011. THERMOGLAZE ASSEMBLY MN-1716ENThermoglaze TNG-2011. THERMOGLAZE ASSEMBLY ThermoglazeMN-1716EN TNG-2011. THERMOGLAZE ASSEMBLY MN-1716ENThermoglaze Thermoglaze MN-1716ENMN-1716EN ThermoglazeThermoglaze MN-1716ENMN-1716EN ThermoglazeThermoglaze MN-1716ENTHERMOGLAZE SK-1258 R5MN-1716EN ThermoglazeTROUBLESHOOTING GUIDE SYMPTOMIMPINGER CTI POSSIBLE CAUSEOven will not heat Conveyor will not run S/N 4000480 and BelowConveyor speed varying or intermittentConveyor will not run S/N 3000481 & AboveConveyor speed varying or intermittentREMOVAL, INSTALLATION, AND ADJUSTMENT SWITCH, ON-OFFMODEL SERIES POTENTIOMETER, CONVEYOR CONTROLAIR PRESSURE SWITCH - REPLACEMENT ADJUSTMENT SCREWAIR PRESSURE SWITCH - ADJUSTMENT THERMOSTAT, OVEN CAVITY HI-LIMITMAIN FAN RELAY TIME DELAY RELAYRELAY CONTACTOR TRANSFORMER - CONVEYORASSEMBLY OF MAGNET TO MOTOR CONVEYOR CONTROL BOARD - REPLACEMENTELECTRONIC TEMPERATURE CONTROL BOARD - REPLACEMENT ELECTRONIC TEMPERATURE CONTROL - CALIBRATIONAIR SWITCH TEMPERATURECONTROLBOARD HI-LIMITOVEN BACK ASSEMBLY COOLING FAN, CONTROL BOXCAPACITOR, MOTOR CAUTION DISCHARGE CAPACITOR BEFORE REMOVINGTHERMOCOUPLE INFORMATIONJ U N C T I O N T E M P E R A T U R E O V E N T E M P E R A T U R EPART# PART#PART# PART#GENERAL - 1300 SERIES LETTERDESCRIPTION GENERAL - 1300 SERIES PARTS BLOW-UP NovemberCOUNTER TOP IMPINGER CONTROL COMPARTMENT - 1300 SERIES LETTERDESCRIPTION CONTROL COMPARTMENT - 1300 SERIES BLOW - UP NovemberCOUNTER TOP IMPINGER BACK - 1300 SERIES LETTERDESCRIPTION BACK - 1300 SERIES BLOW - UP NovemberCOUNTER TOP IMPINGER STANDARD CONVEYOR - 1300 SERIES LETTERDESCRIPTION EXTENDED CONVEYOR - 1300 SERIES LETTERDESCRIPTION