Specifications, Optical, Electrical, Terminals | BenQ SP890 specification

Specifications

All specifications are subject to change without notice.

Optical

Projection system			Single-chip DLP™ system.
DMD chip			0.65" DLP (1920 x 1080)
Lens			F = 2.48 to 2.81, f = 24.1 to 36.15 mm
Projection screen size			28" to 500"
Lamp			300W
		Electrical	PC: 640 x 400 to 1920 x 1200


Compatibility
			Video: NTSC, PAL, SECAM, YPbPr (480i/480p/576i/576p), HDTV
			(720p/1080i/1080p)
			DDC 2B
Color Space			Typ. = 70% NTSC (Target Color Gamut = HDTV Rec. 709)
		Terminals	Analog RGB: D-Sub 15-pin (female) x 1


Input
			HDMI (V. 1.3) x 1
			Component Video (Y/CB/CR, Y/PB/PR) x 1
			Component Video (Y/CB/CR, Y/PB/PR) x 1 (shared with RGB input)
			Composite Video x 1
			S-Video x 1
			PC Audio x 1
Output			12VDC (Max. 0.5 A)
			Analog RGB: D-Sub 15-pin (female) x 1
			PC Audio x 1
Control			Serial Connector: RS232 9 pin (male)
			Mini B type USB x 1
			IR receiver x 2
			RJ45 x 1
		General characteristics


Projector weight			< 7.2 kg (15.9 lbs)
Power			VAC 100-240V, 5A, 50-60Hz (Automatic)
Power consumption			Max. 470W; Standby < 1 W
Operating temperature			0 °C to 35 °C at sea level
Operating humidity			10% - 90% (without condensation)
Operating altitude			0-1499 m at 0°C-35°C
			1500-3000 m at 23°C-30°C (with High Altitude Mode on)
Storage temperature			-20°C- 60°C/-4°F to 140°F
Storage humidity			10% - 90%

English

Additional information

57

Image 57

BenQ SP890 user manual Specifications, Optical, Electrical, Terminals

Contents

Welcome Table of contents Important safety instructions Do not cover the projector with any item Moisture condensation Avoid volatile liquidsDisposal Overview Shipping contents Remote control batteries Remote control operationCeiling mounting the projector Projector features Front and upper side view Projector exterior viewRear view Under view Control panel Remote control Floor Front Choosing a locationCeiling Front Floor Rear Obtaining a preferred projected image size Installation for a 169 ratio screen Projection dimensions Highest Installation for a 43 ratio screenLens Height H To use the lens shift lever Shifting the projection lens Preparations Connecting Hdmi devicesReference Picture quality Component Connecting S-Video or video devices Connecting component-video devices Connecting a computer Connecting a monitorConnect the projector to a computer with a VGA cable Preparations Turning the projector on Using the OSD menu Selecting an input sourceChanging Color Space Using a security cable lock Using the menusUse / to highlight the System Setup menu Securing the projector Utilizing the password function Setting a passwordIf you forget the password Entering the password recall procedure Changing the passwordDisabling the password function Adjusting the projection angle Adjusting the projected imageAuto-adjusting the image Fine-tuning the image size and clarity Correcting picture distortion Two parallel sidesNo parallel sides Selecting a preset mode Using the preset and user modesFine-tuning the selected picture mode To fine-tune the picture mode Resetting the picture mode Setting the User 1/User 2 modePress to highlight Load Settings From To reset the picture mode to the preset factory values Fine-tuning the picture quality Selecting a color temperature Setting Black LevelAdvanced picture quality controls Controlling image clarity Selecting a Gamma setting Setting a preferred color temperatureAdjusting Brilliant Color To set a preferred color temperature Setting Film Mode To adjust and store the settingsColor Management Setting 3D Comb Filter Selecting the aspect ratioAbout the aspect ratio Image Using the entire resolution Using Panamorph lenses optionalAspect ratio Aspect ratio image 169 display Disable Utilizing FAQ functionHiding the image Freezing the image Adjusting the sound level Adjusting the soundTurning off the Power On/Off Ring Tone Muting the sound Controlling the projector through a Lan environment Configuring the Lan Control SettingsControlling the projector remotely through a web browser If you are in a Dhcp environment Auto Source Ii To switch input source, click on your desired signalMenu item Press Exit to go back to the remote network operation To activate High Altitude Mode Press to highlight High Altitude ModeOperating in a high altitude environment To display the PIP window Displaying more than one image source simultaneouslyHighlight PIP and press / to select On PIP function is effective at below source combinations Turning the projector off On-Screen Display OSD menus On-Screen Display OSD structureMain menu Sub-menu Options Display System Setup Information Setup Picture -- Basic menu Picture -- Advanced menuFunction Description Display menu Menu Settings Menu Position Sleep TimerClosed Caption Enable Language Advanced Setup menu Information menu Cleaning the projector case Cleaning the lensCare of the projector Storing the projector Setting Auto Off Setting Lamp Power as EconomicLamp information Getting to know the lamp hour Timing of replacing the lamp Replacing the lampStatus Message Reapply power and turn the projector back on Resetting the lamp timer Power Temp Lamp Status & Description Indicators Problem Cause Remedy Troubleshooting Optical SpecificationsElectrical Terminals Mm x 318 mm x 169 mm W x D x H Dimensions Format Resolution Refresh rate Frequency Timing chartSupported timing for PC input KHz MHz Format Resolution Refresh rate Freq. KHz Pixel Freq MHz Format Resolution Refresh rate Hz Freq. KHz Pixel Freq. MHzSupported timing for Edtv and Hdtv via Component inputs Supported timing for Video and S-Video inputs Warranty CopyrightDisclaimer EEC statement for European users FCC statement for United States usersMIC statement Weee directive English