ENGLISH | (Original instructions) |
uPlace the steam mop on the resting mat and wait until it cools down. (approximately five minutes)
uPlace the front of your shoe onto the cleaning pad removal tab (14) and press down firmly.
uLift the steam mop up off the cleaning pad.
Caution! Always place the steam mop on the resting mat (7) with the handle (4) in the upright position when stationary and make sure the steam mop is turned off when not in use.
Attaching the carpet glider (Fig. F) (FSM1600 & FSM1600D only)
uPlace carpet glider on the floor.
uLightly press the steam mop down onto the carpet glider
(8)until it clicks into place.
Caution! Always place the steam mop on the resting mat (7) with the handle (4) in the upright position when stationary and make sure the steam mop is turned off when not in use.
Removing the carpet glider (Fig. G) (FSM1600 & FSM1600D only)
Caution! Always wear suitable shoes when changing the carpet glider on your steam mop. Do not wear slippers or open toed footwear.
uReturn the handle (4) to the upright position and turn the steam mop ‘OFF’.
uPlace the steam mop on the resting mat and wait until it cools down. (approximately five minutes)
uPlace the front of your shoe onto the carpet glider removal tab (15) and press down firmly.
uLift the steam mop up off the carpet glider (8).
Caution! Always place the steam mop on the resting mat (7) with the handle (4) in the upright position when stationary and make sure the steam mop is turned off when not in use.
Filling the water tank (Fig. H, I & J)
This Steam Mop incorporates an
Note: Fill the water tank with clean tap water.
Note: In areas of very hard water, the use of
uEnsure that the appliance is switched off and the power cord is disconnected from the mains.
uPlace the steam mop on the resting mat (7) with the handle (4) in the upright position.
uRemove the filler cap (16) by turning it
uFill the tank (3) with water.
Warning! Your tank has a 0.5 litre capacity. Do not fill the tank above the Max fill mark.
uFit the filler cap (16) by turning it firmly clockwise.
Note: When not in use, the jug may be clipped to the handle for convenient storage (Fig. J) (FSM1600 & FSM1600D only)
Note: Ensure the filler cap is firmly secured. Incorrect fitting of the filler cap will prevent the steam mop from starting.
Use
Switching on and off
uTo switch the appliance on, press the ON/OFF button (1). It takes approximately 15 seconds for the steam mop to heat up.
Note: When the steam mop is first turned on the water res- ervoir will glow red. Once the steam mop is ready to use the water reservoir will glow blue.
uTo switch the appliance off, press the ON/OFF button (1). Caution! Never leave the steam mop in one spot on any surface for any period of time. Always place the steam mop on the resting mat (7) with the handle (4) in the upright position when stationary and make sure the steam mop is turned off when not in use.
Caution! Always empty the steam mop after use.
AutoselectTM Technology
This steam mop is fitted with an AutoselectTM dial (2) which shows various cleaning applications. They are used to select the correct operating mode for your particular cleaning opera- tion.
Using the AutoselectTM dial (2), choose from one of the follow- ing applications:
Wood/Laminate
Stone/Marble
Tiles/Vinyl
The steam mop will select the correct volume of steam required for your particular cleaning operation.
Hints for optimum use
General
Caution! Never use the steam mop without first attaching a cleaning pad.
uAlways vacuum or sweep the floor before using the steam mop.
uThe easiest way to use the machine is to tilt the handle to a 45˚ angle and clean slowly, covering a small area at a time.
uDo not use chemical cleaners with your steam mop. To remove stubborn stains from vinyl or linoleum floors, you can
6
