Steam cleaning
uPlace a cleaning pad (6) on the floor with the ‘hook & loop’ side facing up.
uRaise the steam mop off the resting mat (7) and lightly press it down onto the cleaning pad (6).
uPlace the steam mop on the resting mat.
uConnect the steam mop to the mains.
uTurn the AutoselectTM dial (2) to the required setting.
uPress the ON/OFF button (1). It takes approximately 15 seconds for the steam mop to heat up.
uPulling the handle (4) back will activate the steam pump. After a few seconds steam will start to come out of the steam head.
uIt take a few seconds for steam to enter the cleaning pad. The steam mop will now glide easily over the surface to be sanitised/cleaned.
uPush and pull the steam mop slowly across the floor to thoroughly steam clean each section.
Note: During use you may turn off the steam pump by return- ing the handle to the upright position, this convenient feature will allow you to place the steam mop on the resting mat for a short time so that you may move items of furniture, then continue cleaning without the need to switch the appliance off.
uWhen you have finished using the steam mop, return the handle (4) to the upright position and turn it ‘OFF’, place it on the resting mat (7) and wait until the steam mop cools down. (approximately five minutes)
Caution! It is important to monitor the water level in the water tank. To refill the water tank and continue to sanitise/clean, return the handle (4) to the upright position and turn the steam mop ‘OFF’. Unplug the unit from the electrical wall outlet and refill the water tank (3) using the jug (9) supplied.
Caution! Never leave the steam mop in one spot on any surface for any period of time. Always place the steam mop on the resting mat (7) with the handle (4) in the upright position when stationary and make sure the steam mop is turned off when not in use.
Carpet refreshing
uPlace a cleaning pad (6) on the floor with the ‘hook & loop’ side facing up.
uRaise the steam mop off the resting mat (7) and lightly press it down onto the cleaning pad (6).
uPlace the carpet glider (8) on the floor.
uLightly press the steam mop down onto the carpet glider
(8)until it clicks into place.
uPlace the steam mop on the resting mat. (7)
uConnect the steam mop to the mains.
uTurn the AutoselectTM dial (2) to the Wood/Laminate set- ting.
uPress the ON/OFF button (1). It takes approximately 15 seconds for the steam mop to heat up.
(Original instructions) | ENGLISH |
uPulling the handle (4) back will activate the steam pump. After a few seconds steam will start to come out of the steam head.
uPush and pull the steam mop slowly across the carpet to thoroughly refresh each section.
Note: During use you may turn of the steam pump by return- ing the handle (4) to the upright position, this convenient feature will allow you to place the steam mop on the resting mat (7) so that you may move items of furniture with out the need to switch the appliance off.
uWhen you have finished using the steam mop, return the handle (4) to the upright position and turn it ‘OFF’, place it on the resting mat (7) and wait until the steam mop cools down. (approximately five minutes)
Caution! It is important to monitor the water level in the water tank. To refill the water tank and continue to sanitise/clean, return the handle (4) to the upright position and turn the steam mop ‘OFF’. Unplug the unit from the electrical wall outlet and refill the water tank using the jug supplied.
Caution! Never leave the steam mop in one spot on any surface for any period of time. Always place the steam mop on the resting mat (7) with the handle (4) in the upright position when stationary and make sure the steam mop is turned off when not in use.
After use (Fig. K & L)
uReturn the handle (4) to the upright position and turn the steam mop ‘OFF’,
uPlace the steam mop on the resting mat (7) and wait until the steam mop cools down. (approximately five minutes)
uUnplug the steam mop from the electrical wall outlet.
uEmpty the water tank (3).
uRemove the cleaning pad (6) and wash it ready for next use. (Take care to follow the wash care instructions printed on the cleaning pad).
uWrap the supply cable around the cable tidy hooks (18 & 19).
Note: The top cable tidy hook (19) rotates to easily release the cable ready for next use.
uClip the supply cable into the cable tidy clip (20) close to the plug.
uPlace steam mop on the resting mat (7) for storage. Note: With the handle (4) in the upright position, the cable neatly wrapped around the cable tidy hooks (18 & 19) and secured in the cable tidy clip (20) your steam mop will stand on its own for storage. Alternatively there is a hanging bracket (21) built into the hand grip (10) which will allow your steam mop to be hung from a suitable hook on the wall. Always ensure that your wall hook is capable of supporting the weight of the steam mop safely.
7
