Maintenance and care |
| For perfect rinsing results ... |
|
| Cleaning the | |
Strainers ... | Rotate filter | rinse under | Insert ... | Screw in filter | * With some models | |
± Ladle out water and remove filters | ||||||
Check, if | cylinder, remove | flowing water ... |
| system NOTE | ||
required, clean | filter system ... |
|
| MARK! | ± Unscrew cover (Torx T20) | |
|
|
|
|
| ± Check area of fan impeller for foreign objects | |
|
|
|
|
| ± Screw in cover and insert filters | |
|
|
|
|
|
| |
|
|
|
|
|
| |
Spray arms ... | Pull lower arm | Unscrew upper | Clean spray nozzles | Insert lower arm ... |
| |
Remove | upwards ... | arm ... | under flowing water |
|
| |
blockages/deposits |
|
| (perhaps with |
|
| |
|
|
| toothpick) ... |
|
| |
|
|
|
| Screw in upper arm |
| |
|
|
|
|
| ||
|
|
|
|
|
| |
Eliminating minor faults yourself ... | ... Self±help pays! |
|
|
|
Fault | Possible Cause | Remedy |
|
|
|
Residual water in the device | Clean | |
| Programme not yet ended | Switch on appliance and close or |
|
| terminate programme (see Terminating |
|
| the programme). |
|
|
|
|
|
|
Device does not work/stops | Supply fitting not open | Open supply fitting. |
| Supply hose kinked | Lay supply hose without kinks. |
| Supply fitting jammed or calcified | 1. Unscrew water connection. |
|
| 2. Clean filter in the water connection. |
|
| 3. Flow rate must be min. 9 l/min when |
|
| the water inlet is open. |
|
| If the flow rate is less, replace the |
Fault | Possible Cause | Remedy |
|
|
|
Dishes not clean | Utensils are situated too close to each | Spread out the utensils, avoid contact |
Sand or grainy residues | other or on top of each other | between the utensils. |
| Follow manufacturer's specifications | |
on dishes | Too little cleaning product | |
|
| (detergent). |
| Unsuitable programme selected | Select more intensive programme. |
| Spray nozzles blocked | Clean spray arms (see above). |
| Filters dirty, not installed securely | Clean the strainers (see above). |
| Spray arms blocked | Arrange the utensils so that the spray |
|
| arms can rotate freely. |
|
|
|
|
|
|
Stains and streaks | Rinse aid dosage too high / too low | Streaks: Reduce dosage. |
|
| supply fitting. | |
|
|
| |
|
|
| |
Plastic parts / parts of | Too little cleaning product | Follow manufacturer's specifications | |
Discoloration caused by food colourings | (detergent). | ||
dishes discoloured | |||
Discoloration is quite safe; fades after | |||
| (tomato sauce) | ||
|
| subsequent rinse cycles. | |
|
|
| |
|
|
| |
Cutlery rusty | Cutlery not | Use | |
| Hard knife blades are more susceptible |
| |
| Extraneous rust | Never wash rusting parts in the | |
|
| appliance. | |
|
|
|
Milky residues on dishes (can be removed)
Milky film, glasses cloudy / dull (cannot be removed)
Water softening system incorrectly set; no special salt
Glasses not
Water or limescale stains: Increase dosage.
Set water softening system correctly.
Refill with special salt.
Use
Use
Further advice can be found in the instruction manual
Stopping the programme ...
Press and hold the two
reset buttons simultaneously for approximately 3 seconds while the programme is running (RESET)
º0º appears
Switch off the appliance.
The programme will stop after 1 minute
Loading the dishwasher correctly ...
Arrange