Solution 64 
User Guide
Trouble Condition | Description | |
Mains Missing | The system has detected that the AC mains supply has failed or is disconnected. If there is not a general power outage | |
in your area then you should contact your security company. | ||
| ||
|
| |
Battery Low | The backup battery has failed the periodic test which the system performs on a regular basis. You should contact your | |
security company as the battery may need replacing. | ||
| ||
|
| |
Battery Missing | The system has detected that its backup battery has been disconnected. | |
|
| |
Battery Reversed | The system has detected that backup battery has not been connected correctly. | |
You should contact your security company. | ||
| ||
|
| |
Voltage Low | The voltage reading the keypad has fallen below the minimum programmed by the security company. | |
|
| |
Voltage High | The voltage reading at the keypad has increased above the maximum programmed by the security company. | |
|
| |
RF Rxer Missing | The system has detected that the RF receiver is disconnected. | |
|
| |
RF Rxer Tamper | The system has detected that the tamper circuit on the RF receiver is faulted. | |
|
| |
RF Rxer Jammed | The system has registered a jamming fault from the RF receiver. This situation may preven certain parts of your system | |
from working correctly. You should contact your security company. | ||
| ||
|
| |
Comms Trouble R1 | The system has failed to send reports to the primary report contact. You should contact your security company. | |
|
| |
Comms Trouble R2 | The system has failed to send reports to the secondary report contact. | |
You should contact your security company. | ||
| ||
|
| |
Comms Test Fail | The system has failed to send its periodic report to the monitoring station. | |
You should contact your security company. | ||
| ||
|
| |
Buss Trouble | The system has failed to communicate to a system device (e.g. keypad etc). | |
|
| |
Default PIN Trbl | The system has detected that either the Installer PIN or User 1 PIN has not been changed from the factory default codes. | |
These codes should be changed immediately to prevent a security risk. | ||
| ||
|
| |
Date And Time | The system date and time needs to be set. | |
|
| |
Cabinet Tamper | The system has detected that someone has tampered with its metal enclosure or that it has been forced open. Inspect | |
and contact your security company if necessary. | ||
| ||
|
| |
Siren Trouble | The system has detected that the external siren has failed or has been disconnected from the system. | |
|
| |
Telco Line Trouble | The system has detected that its telephone line has been disconnected for a minimum of 30 seconds. | |
|
| |
LAN Overload | The system has detected that the current load has exceeded the maximum LAN rating. | |
You should contact your security company. | ||
| ||
|
| |
Comm+ Overload | The system has detected that the current load has exceeded it’s maximum COMM+ rating. | |
You should contact your security company. | ||
| ||
|
| |
Accessory Overld | The system has detected that the current load has exceeded it’s maximum ACCS+ rating. | |
You should contact your security company. | ||
| ||
|
| |
Time For Service | The system displays this trouble condition to remind you that a service call is due. | |
|
| |
Memory Fault | The system has detected an error with its internal memory. You should contact your security company. | |
|
| |
Default Memory | The system memory has reset to factory default. You should contact your security company. | |
|
| |
Service Mode | The security installer has entered service mode. | |
|
| |
Phone In Use | The system is using the phone line. | |
|
|
Table 5: Control PanleTrouble Messages
Bosch Security Systems |
| 09/06 |
| BLCC110U | 25 |
|
|
