LTC 8016/90 Instruction Manual Installation | EN 12 |
|
|
4.5Video Connections to the Controller Unit
Video connections from the Interface Unit vary based on the type of video connections available on the controller, and the distance between the controller and the Interface Unit. Review the options in the table below to determine which best suits your configuration, then follow the appropriate section below:
Controller Type | Configuration | Max Separation |
| Method | Distance |
|
|
|
Allegiant Series LTC 8200, | Use | 2 m (6 ft) |
LTC 8300, LTC 8600, | video ribbon |
|
LTC 8800, and LTC 8900, | cable, supplied |
|
DESAXL DVR Series | with the |
|
| LTC 8016 |
|
|
|
|
Any controller system | Use the optional | 1 m (3 ft) |
using BNC connectors | LTC 8508/01 |
|
|
| |
|
| |
| video cable |
|
|
|
|
Any controller system | Use the | Distance is |
using BNC connectors | limited only by | |
| video ribbon | the type of user- |
| cable supplied | supplied video |
| with the | transmission link |
| LTC 8016, to |
|
| the optional |
|
| LTC 8807/00 |
|
| panel, then |
|
| BNC to user- |
|
| supplied video |
|
| link |
|
Video output signals from the Interface Unit are expecting to see a standard 75Ω termination. Unless a video input will be used to loop out to another device, make sure that the video inputs on the control unit are properly set to provide 75Ω video termination. For details on setting the video terminations of your controller device, refer to the device’s installation instructions.
The video connections from the Interface Unit MUST be kept in consecutive order, and the group must always end at an exact multiple of 16. For example, the lowest camera group range is from 1 to 16. The next group range is from 17 to 32, and so on, up to the last group, that corresponds to the camera range of 9985 to 9999. Always make video connections to the controller following these guidelines.
Certain controller units support video looping inputs. Do not connect a camera to the looping output of a video channel on the control unit that is already being used by the Interface Unit. Smeared or double video images will result. Alternate video connections available on video control systems should only be used for looping video signals out to some other external control system device or monitor.
4.5.1Video Connections to Products Supporting Ribbon Cable Interface
Video connections from the Interface Unit to Allegiant models LTC 8200, LTC 8300, LTC 8600, LTC 8800, LTC 8900, and the DESAXL Series Digital Video Recorders use the supplied video ribbon cable. Noting the video ribbon cable connector’s orientation and alignment tab, connect one end of the supplied
to video inputs 33 to 48.
PC | |
DATA |
|
| CODE |
|
|
|
| ETHERNET |
|
|
|
| |
|
|
|
|
| 10/100 BaseT |
|
|
|
| ||
|
|
|
|
| LINK |
| ACT | 15 | 13 | 11 | 9 |
|
|
|
|
|
|
|
| ||||
BIPHASE IN |
|
|
|
|
|
| INPUTS |
|
| ||
| 0 |
|
| 0 |
|
| 0 |
|
|
| |
8 | 8 |
| 8 |
|
|
|
|
| |||
2 |
| 2 |
| 2 |
| 14 | 12 |
| |||
6 | 4 |
| 6 | 4 |
| 6 | 4 | 16 | 10 |
GROUP ID
LOOPING VIDEO
. . . . . . . . . . . . . . . . . |
. . . . . . . . . . . . . . . . . |
7 | 5 | 3 | 1 |
8 | 6 | 4 | 2 |
LTC 8016 Interface Unit |
|
|
|
| 2m (6ft) Supplied |
|
|
| |||||
|
|
|
|
|
|
|
| ||||||
|
|
|
|
| Video Ribbon Cable |
|
|
| |||||
| LTC8200 |
|
|
|
|
|
|
|
|
|
|
| ALARM |
|
|
|
|
|
|
|
|
|
|
|
|
| |
CONSOLE | 1 | 2 | 3 | 4 | 5 | 1 | 2 | 3 | 4 | 5 | 6 | 7 | 8 |
|
| MONITOR OUTPUTS |
|
|
|
|
|
| CAMERA INPUTS |
|
|
|
| . . . . . . . . . . . . . . . . . |
|
|
|
|
|
|
| BIPHASE OUT | BIPHASE OUT | BIPHASE OUT |
KEYBOARD | . . . . . . . . . . . . . . . . . | 9 | 10 | 11 | 12 | 13 | 14 | 15 | 16 |
|
|
Video Looping Ribbon Connector
LTC 8200 Allegiant Series Switcher
Figure 3 Interface Unit Video Connections to a Typical Allegiant System
Bosch Security Systems 18 August 2005