Bosch Appliances LTC 8016/90 En, Bosch Security Systems 18 August, LTC 8016 Interface Unit

LTC 8016/90 Instruction Manual Installation

4.5.2Video Connections to Products via LTC 8508/01 Ribbon-to-BNC Cable

Video connections to Allegiant models LTC 8100, LTC 8500, and other products using BNC video connectors, can utilize the 1 m (3 ft) 16-channel LTC 8508/01 Ribbon-to-BNC cable (sold separately). One LTC 8508 cable is required for each Interface Unit being installed. Noting the connector orientation and alignment tab, connect the ribbon connector end of the cable to the Interface Unit. Attach the BNC

EN 13

ends to the video inputs on the rear panel of the controller that corresponds to the physical camera number range previously determined by the Group ID switch settings above. For example, if the Group ID switches have been set to 001, the BNC ends of the video ribbon cable should be installed in the controller’s video inputs 1 to 16. For your convenience, the BNC ends are marked with the video channel number.

			CODE				ETHERNET
							10/100 BaseT
							LINK		ACT	15	13	11	9
PC	RS-485 IN
DATA		BIPHASE IN									INPUTS
		0		8		0	8	0
		8	2			2			2			12
RS-232	RS-485 OUT	6	4		6	4	6	4		16	14		10
				GROUP ID

LTC 8016 Interface Unit

LOOPING VIDEO 1-16

. . . . . . . . . . . . . . . . .

. . . . . . . . . . . . . . . . .

7 5 3 1

8 6 4 2

1 m (3 ft) LTC 8508/01 Ribbon-to-BNC

Cable (Purchased

Separately)

16 BNC

Connectors

Connect to Video Input

Connectors on Control Unit

Divar Digital Versatile Recorder																		BOSCH
LIVE	SEARCH	ACK	ALT
			1	2	3	4	5	6	7	8	9	10	11	12	13	14	15	16
F1	F2	ESC							A	B

Figure 4 Typical Video Connections to Divar Series DVR Control Units

4.5.3Video Connections to Products via LTC 8807/00 Video Interconnect Panel

If using a rack-mountable BNC patch panel, or if the Interface Unit will be remoted some distance from the controller unit, an LTC 8807/00 Video Interconnect Panel (sold separately) can be used for video connections to a controller. Each LTC 8807 panel can be used with up to two Interface Units, supporting a maximum of 32 cameras. Connect the supplied video ribbon cable from the Interface Unit into the upper connector on the back of the LTC 8807 for the first block of 16 cameras. The lower connector is only used if a second Interface Unit will be connected, providing a second block of 16 cameras.

User-supplied coax jumper cables are required to complete the video connections between the LTC 8807 panel and the BNC connectors on the controller unit. Attach the coax to the video inputs on the rear panel of the controller bay, that correspond to the physical camera number range previously determined by the Group ID switch settings above. For example, if the Group ID switches have been set to 001, the coax cables should be installed into the controller’s video inputs 1 to 16.

If the control unit will be located at a remote distance from the Interface Unit, standard practices for video signal transmission, and the associated data interface, should be used (more details provided in the next section).

LTC 8016/90 Interface Unit

BOSCH

POWER

Interface

Supplied 16-ChannelData

LTC 8809 Video Cable

Follow Standard

Practices for Remoting

Coax & Data Cables

LTC 8807/00 Interconnect Panel

Video

(sold separately) for use with up to two (2) LTC 8016 units

Signals

Typical Remoted DVR

Customer-supplied

Video Coax

or Other Biphase- enabled Controller

Figure 5 Video Connections to Control System Located at Remote Site

Bosch Security Systems 18 August 2005