Operating Generator | Briggs & Stratton 01933-1 guide

BSPP Generator

OPERATING THE

GENERATOR

Starting the Engine

Disconnect all electrical loads from the generator. Use the following start instruction steps in numerical order:

1.Make sure unit is on a level surface.

IMPORTANT: Failure to start and operate unit on a level surface will cause the unit not to start or shut down during operation.

2.Turn fuel valve to “On” position (Figure 4).

Figure 4 — Fuel Shut-off Valve

3.Make sure Idle Control switch is in “Off” position (Figure 5).

Figure 5 — Idle Control Switch

4.Follow start instructions given in engine operator’s manual.

WARNING

Running engines produce heat.Temperature of muffler and nearby areas can reach or exceed 150°F (65°C).

Severe burns can occur on contact.

Exhaust heat/gases can ignite combustibles, structures or damage fuel tank causing a fire.

•DO NOT touch hot surfaces and avoid hot exhaust gases.

•Allow equipment to cool before touching.

•Keep at least 5 ft. (152 cm) clearance on all sides of generator including overhead.

•Code of Federal Regulation (CFR) Title 36 Parks, Forests, and Public Property require equipment powered by an internal combustion engine to have a spark arrester, maintained in effective working order, complying to USDA Forest service standard 5100-1C or later revision. In the State of California a spark arrester is required under section 4442 of the California Public resources code. Other states may have similar laws.

Connecting Electrical Loads

•Let engine stabilize and warm up for a few minutes after starting.

•Plug in and turn on the desired 120 and/or 240 Volt AC, single phase, 60 Hz electrical loads.

•DO NOT connect 240 Volt loads to the 120 Volt duplex receptacles.

•DO NOT connect 3–phase loads to the generator.

•DO NOT connect 50 Hz loads to the generator.

•DO NOT OVERLOAD THE GENERATOR. See “Don’t Overload Generator”.

WARNING

Rapid retraction of starter cord (kickback) will pull hand and arm toward engine faster than you can let go.

Broken bones, fractures, bruises or sprains could result.

•When starting engine, pull cord slowly until resistance is felt and then pull rapidly to avoid kickback.

•NEVER start or stop engine with electrical devices plugged in and turned on.

NOTE: If engine starts after 3 pulls but fails to run, or if unit shuts down during operation, make sure unit is on a level surface and check for proper oil level in crankcase.

This unit may be equipped with a low oil protection device. See engine operator’s manual.

CAUTION

Exceeding generators wattage/amperage capacity can damage generator and/or electrical devices connected to it.

•See “Don’t Overload Generator”.

•Start generator and let engine stabilize before connecting electrical loads.

•Connect electrical loads in OFF position, then turn ON for operation.

•Turn electrical loads OFF and disconnect from generator before stopping generator.

01933-1 specifications

The Briggs & Stratton 01933-1 is a powerful and reliable portable generator designed to meet the diverse needs of users, whether for home use, construction sites, or recreational activities. This versatile generator stands out due to its robust performance, innovative technologies, and user-friendly features.

One of the primary features of the Briggs & Stratton 01933-1 is its impressive power output. With a peak wattage of 7,500 watts and a running wattage of 6,000 watts, this generator provides ample electricity to run essential appliances, power tools, and other equipment during outages or outdoor adventures. The generator's ample starting power ensures that it can easily handle high-demand devices such as refrigerators, air conditioners, and other household electronics.

Equipped with a powerful Briggs & Stratton engine, this generator features a reliable 306cc overhead valve design that enhances fuel efficiency and performance. The engine's low-oil shutdown feature adds an additional layer of protection, automatically turning off the generator when oil levels drop too low, preventing potential damage and extending the lifespan of the unit.

The Briggs & Stratton 01933-1 incorporates advanced technology with its Easy Start System, which allows for effortless starting in various conditions. The generator is designed for optimal fuel consumption, allowing users to maximize run time on a single tank of gas, which is particularly beneficial during extended power outages or remote work sites.

Another noteworthy characteristic is the generator's durable construction. Built with a heavy-duty frame and oversized wheels, the 01933-1 can handle rough terrains and is easy to transport. The generator's compact design does not compromise stability, providing a secure operating platform without excessive noise levels, thanks to its sound-dampening features.

Safety is prioritized in the Briggs & Stratton 01933-1, as it includes several safety features such as circuit breakers and grounded outlets that help protect against overloads and ensure safe operation. Additionally, it has multiple outlets, including a 120/240V outlet, making it versatile enough for a wide range of applications.

In conclusion, the Briggs & Stratton 01933-1 is an excellent choice for anyone in need of a dependable and efficient portable generator. With its powerful performance, advanced engine technology, and robust safety features, it is well-equipped to provide reliable power wherever and whenever required. Whether you are preparing for emergencies, working on a job site, or enjoying outdoor activities, the Briggs & Stratton 01933-1 is a generator that can truly meet your power needs.

Briggs & Stratton 01933-1 Operating Generator, Starting the Engine, Connecting Electrical Loads

Models: 01933-1