Manuals / Brocade Communications Systems / Computer Equipment / Switch

Brocade Communications Systems 53-1001761-01 Managing and displaying the FCoE login configuration

Models: 53-1001761-01

1 164

Download 164 pages 21.05 Kb

Page 147

Managing and displaying the FCoE login configuration

13

Perform the following task to configure FIP multicast advertisement intervals.

Task	Command

Configure FIP multicast advertisement intervals.	switch:admin> fcoe --fipcfg -advintvl intvl
Syntax is as follows:

•intvl—Specifies the interval in seconds. The minimum interval value is 0 seconds and the maximum value is 300 seconds. A value of 0 cancels the previous advertisement interval value.

Clearing logins

Perform the following task to clear logins.

Task		Command

Clear the logins that occurred through a front-end		switch:admin> fcoe --resetlogin -teport slot/port
port or from a device specified by the Enode's		-device wwn
VN_port WWN. Syntax is as follows:
• -teportslot/port—Specifies the slot or port
•	number.
•	-devicewwn—Specifies the device WWN.

Displaying FCoE configuration-related information

Perform the following tasks to display FCoE-related configuration information.

Task	Command

Display the embedded FCoE port configuration.	switch:admin> fcoe --cfgshow[port]
Configurations of all the ports are displayed if you
do not specify a specific port.

Display information about devices logged into a	switch:admin> fcoe --loginshow [port]
specific FCoE F_port.

Display FIP configurations.	switch:admin> fcoe --fipcfgshow

Managing and displaying the FCoE login configuration

Another important task in administrating FCoE is configuring the FCoE login information.

Enabling or disabling FCoE login configuration management

The fcoelogincfg command allows only configured Enode VN_ports to log in. Use the fcoelogingroup command to configure allowed Enode VN_ports. The default is disabled.

Disabling the fcoelogincfg command allows unrestricted login on Enode VN_ports.

Converged Enhanced Ethernet Administrator’s Guide	125
53-1001761-01

Image 147

Brocade Communications Systems 53-1001761-01 manual Managing and displaying the FCoE login configuration, Clearing logins

Contents

Converged Enhanced Ethernet Brocade Communications Systems, Incorporated Contents This chapter Vlan overview Chapter Using the CEE CLIChapter Configuring Link Aggregation using the CEE CLI This chapter QoS overview Chapter Configuring Lldp using the CEE CLIActive Igmp snooping This chapter802.1x protocol overview About IgmpCEE configuration management guidelines and restrictions Chapter FCoE configuration using the Fabric OS CLIIndex WRR schedule two queues Strict priority and Weighted Round Robin schedulerPage Tables Page About This Document This chapterHow this document is organized Supported hardware and software Text formatting Command syntax conventionsWhat’s new in this document Document conventionsRepeat the previous element, for example membermember Key termsOptional element Enclosed in angled bracketsOther industry resources Additional informationGetting technical help Brocade resourcesFT00X0054E9 Serial number label is located as follows Document feedbackXxi Page Introducing FCoE FCoE terminologyFCoE overview FCoE hardware Layer 2 Ethernet overview Layer 2 forwardingLayer 2 Ethernet overview Vlan tagging Frame classification incoming Loop-free network environmentCongestion control and queuing Access control FIP discovery FCoE Initialization ProtocolTrunking Flow ControlPage FCoE login FIP logoutFCoE logout Logincfg Name serverFC zoning FCoE queuing Using the CEE CLI CEE Command Line InterfaceManagement Tools CEE CLI Rbac permissions Saving your configuration changesSaving configuration changes with the copy command Saving configuration changes with the write commandCEE Command Line Interface Accessing the CEE CLI through the console or TelnetAccessing the CEE CLI from the Fabric OS shell CEE CLI command modesInterface port-channel CEE Command Line Interface CEE CLI command modes CEE CLI keyboard shortcutsLists CEE CLI keyboard shortcuts Displaying CEE CLI commands and command syntax Using the do command as a shortcutCEE CLI command output modifiers CEE CLI command completionCEE Command Line Interface Standard CEE Integrations and Configurations Overview of standard CEE integrationsSAN Integration CEE and LAN integration Integrating a Brocade 8000 switch on a SANCEE and LAN integration About CEE map attributesCreating the CEE map Configuring Dcbx Configuring Spanning Tree Protocol Configuring Vlan MembershipActivate the protocol Example of creating Vlan rules and classifier groups Configuring the CEE InterfacesExample of setting the map name to srvgroup Ethernet configuration for the CNA Server connections to the Brocade 8000 switchMinimum CEE configuration to allow FCoE traffic flow Fibre Channel configuration for the CNASwitchconfig#interface tengigabitethernet 0/0 Configuring VLANs Using the CEE CLI Vlan overviewIngress Vlan filtering Displays the frame processing logic for an incoming frame Default Vlan configuration Vlan configuration guidelines and restrictionsTo disable the CEE interface Vlan configuration and managementConfiguring the MTU on an interface port Vlan configuration and managementCreating a Vlan interface Enabling STP on a VlanDisabling STP on a Vlan Configuring a Vlan interface to forward FCoE traffic Configuring an interface port as a Layer 2 switch portConfiguring an interface port as an access interface Configuring an interface port as a trunk interface Enter the no shutdown command to enable the CEE interfaceDisabling a Vlan on a trunk interface Configuring protocol-based Vlan classifier rules Configuring an interface port as a converged interfaceDisabling a Vlan on a converged interface Configuring a Vlan classifier rule Configuring MAC address-based Vlan classifier rulesDeleting a Vlan classifier rule Displaying Vlan information Creating a Vlan classifier group and adding rulesActivating a Vlan classifier group with an interface port Clearing Vlan counter statisticsAdding static addresses to the MAC address table Configuring the MAC address tableConfiguring the MAC address table Specifying or disabling the aging time for MAC addressesConfiguring the MAC address table STP overview Configuring STP, RSTP, and Mstp using the CEE CLIConfiguring STP on Brocade FCoE hardware Is the interface learning MAC addresses? Rstp overviewConfiguring Rstp on Brocade FCoE hardware For details, see Specifying the port priority on Mstp overviewConfiguring Mstp on Brocade FCoE hardware Switchconf-mstp#instance 1 priority Default STP, RSTP, and Mstp configuration Disabling STP, RSTP, or Mstp STP, RSTP, and Mstp configuration and managementSTP, RSTP, and Mstp configuration and management Enabling STP, RSTP, or MstpSpecifying the bridge forward delay Specify the bridge forward delaySpecifying the bridge priority Specifying the bridge maximum aging time Enabling the error disable timeout timerSpecifying the error disable timeout interval Enable the error disable timeout timerSpecify the port-channel path cost Specifying the port-channel path costSpecifying the bridge hello time STP and Rstp Specifying the transmit hold count Rstp and MstpMap a Vlan to an Mstp instance Enabling Cisco interoperability MstpDisabling Cisco interoperability Mstp Mapping a Vlan to an Mstp instanceSpecifying a name for an Mstp region Specifying a revision number for an Mstp configurationEnter the region command to assign a name to an Mstp region Specifying the maximum number of hops for a Bpdu MstpFlushing MAC addresses Rstp and Mstp Clearing spanning tree countersClearing spanning tree-detected protocols Enabling automatic edge detection Configuring STP, RSTP, or Mstp on CEE interface portsConfiguring the path cost Displaying STP, RSTP, and MSTP-related informationEnabling the guard root Enabling a port interface as an edge portSpecifying restrictions for an Mstp instance Specifying the Mstp hello timeSpecifying a link type Enabling port fast STPSpecifying the port priority Restricting the port from becoming a root port Restricting the topology change notificationEnabling spanning tree Disabling spanning tree Configuring STP, RSTP, or Mstp on CEE interface ports Configuring Link Aggregation using the CEE CLI Link Aggregation Group configurationLink aggregation overview Converged Enhanced Ethernet Administrator’s Guide Data Center Core Brocade-proprietary aggregation Link Aggregation Control ProtocolDynamic link aggregation Static link aggregationLacp configuration guidelines and restrictions Lacp configuration guidelines and restrictionsDefault Lacp configuration Lacp configuration and managementConfiguring the Lacp system priority Configuring the Lacp timeout period on a CEE interfaceClearing Lacp counter statistics on a LAG Lacp troubleshooting tips Clearing Lacp counter statistics on all LAG groupsDisplaying Lacp information Deskew calculation failed for link link-name Lldp overview Configuring Lldp using the CEE CLILayer 2 topology mapping Page Dcbx overview Enhanced Transmission Selection ETSDcbx overview Dcbx interaction with other vendor devices Lldp configuration guidelines and restrictionsDcbx interaction with other vendor devices Priority Flow Control PFCDefault Lldp configuration Default Lldp configurationLldp configuration and management Disabling and resetting Lldp globallyConfiguring Lldp global command options Specifying a system name for the Brocade FCoE hardwareSpecifying a user description for Lldp Configuring the transmit frequency of Lldp frames Configuring the hold time for receiving devicesAdvertising the optional Lldp TLVs Configure the FCoE priority bits Configuring the advertisement of Lldp Dcbx -related TLVsConfiguring FCoE priority bits Advertise the Lldp DCBX-related TLVs using these commandsConfiguring Lldp profiles Clear Lldp statistics Configuring Lldp interface-level command optionsClearing LLDP-related information Apply an Lldp profile to the interfaceDisplay Lldp neighbor-related information Displaying LLDP-related informationDisplay Lldp general information Display Lldp interface-related informationACL overview Configuring ACLs using the CEE CLIDefault ACL configuration VLANs Default ACL configurationACL configuration guidelines and restrictions ACL configuration and managementModifying MAC ACL rules Creating an extended MAC ACL and adding rulesEnter the no seq command to delete the existing rule Removing a MAC ACLReordering the sequence numbers in a MAC ACL Applying a MAC ACL to a Vlan interface Applying a MAC ACL to a CEE interfaceACL configuration and management QoS overview Configuring QoS using the CEE CLIUser-priority mapping Default user-priority mappings for untrusted interfacesRewriting QueueingIncoming CoS User Priority Configuring the QoS trust modeSet the interface mode to ‘3’ Configuring user-priority mappingsSet the interface mode to ‘trust’ Exit the configuration mode and return to Exec modeQueueing Traffic class mappingCreating a CoS-to-CoS mutation QoS map Applying a CoS-to-CoS mutation QoS mapMulticast traffic Unicast trafficMapping CoS-to-Traffic-Class Activating a mapping CoS-to-Traffic-ClassActivate the CoS-to-Traffic-Class mapping by name Congestion control Congestion controlTail drop Verifying a mapping CoS-to-Traffic-ClassChanging the Tail Drop threshold Enabling Ethernet Pause Ethernet pauseEnabling an Ethernet PFC Enable an Ethernet PFC on the interfaceMulticast rate limiting Ethernet Priority Flow ControlScheduling Strict priority schedulingCreating a receive queue multicast rate-limit Deficit weighted round robin scheduling Traffic class scheduling policyScheduling Scheduling the QoS queue Scheduling Supported scheduling configurationsScheduling the QoS multicast queue Multicast queue schedulingConverged Enhanced Ethernet map configuration Define the CEE map for Pgid Creating a CEE mapDefining a priority group table Create a CEE map. In this example, the name ‘test’ is usedDefine the map Defining a priority-table mapSwitchconfig-ceemap#exit Applying a CEE provisioning map to an interface Verifying the CEE mapsVerify the CEE map provisioning for a specified name Configuring 802.1x Port Authentication 802.1x configuration guidelines and restrictions802.1x protocol overview Configuring 802.1x on specific interface ports 802.1x authentication configuration tasksInterface-specific administrative tasks for Configure authentication Between the switch and CNA or NICConfigure reauthentication for the interface port Configuring 802.1x timeouts on specific interface portsConfigure the timeout interval Enable 802.1x authentication for the interface portDisabling 802.1x on specific interface ports Interface-specific administrative tasks forConfiguring Igmp About IgmpActive Igmp snooping Multicast routing Configuring IgmpConfiguring Igmp Configure a Vlan port member to be a multi-router interfaceConfiguring Igmp snooping querier Configuring Igmp snooping querierMonitoring Igmp Switch#show ip igmp groups Configuring Rmon settings Configuring Rmon using the CEE CLIRmon configuration and management Default Rmon configurationConfiguring Rmon Ethernet group statistics collection Configuring Rmon eventsSwitchconf-if-te-0/1#exit Rmon configuration and management FCoE configuration guidelines and restrictions FCoE configuration using the Fabric OS CLIManaging and displaying the FCoE configuration Managing and displaying the FCoE configurationConfiguring Fcmap values for a Vlan Configuring FIP multicast advertisement intervalsEnabling or disabling FCoE login configuration management Managing and displaying the FCoE login configurationClearing logins Displaying FCoE configuration-related informationCleaning up login groups and VNport mappings Displaying or aborting the current configuration transactionCreating an FCoE login group Creating and managing the FCoE login group configurationDisplaying the FCoE login configuration Saving the current FCoE configurationModifying the FCoE login group device list Deleting an FCoE login groupPerform the following task to delete an FCoE login group Perform the following task to rename an FCoE login group Renaming an FCoE login groupCreating and managing the FCoE login group configuration CEE configuration management CEE configuration management guidelines and restrictionsCEE configuration management tasks Erasing the startup configuration file Display the running configuration fileSaving the running configuration file Loading the startup configuration fileArchive a startup configuration from Flash Restore an archived running configuration fileArchiving the startup configuration file Restore an archived startup configuration fileLists the common CEE configuration management commands Flash file management commandsCEE configuration management commands Flash file management commandsSwitch#erase flash Debugging and logging commandsDebugging and logging commands Index Symbols NumericsDcbx FIP Lldp Radius Vlan