Brother HL-1060 Series manual

USER’S GUIDE

Setting Up the Printer for Apple Macintosh Computers

When Using the Optional RS-100M Serial Interface

Question	Recommendation
I cannot print from my	∙ Make sure that the supplied Macintosh printer
application software.	driver is installed in the System Folder and it is
	selected with Chooser.
	∙ Check the PORT selection within the Chooser: it
	should match the port to which you physically
	attached the printer cable.
	∙ The serial slide switch of the optional interface
	board should be in the Apple (RS-422A) position.
	∙ Check the printer cable type: you cannot use a
	LocalTalk or straight-through cable. Refer to
	Chapter 4 for details on printer cable type.

When Using the Optional BR-Script 2 ROM Board BR-3000

Question

The printer does not print.

Recommendation

Check the following:

∙The printer is plugged in.

∙Paper is loaded.

∙No error conditions are active (any blinking lamps on printer.)

∙Printer is on-line.

CHAPTER 6 –12

Image 75

Brother HL-1060 Series manual Setting Up the Printer for Apple Macintosh Computers

Contents

Brother Laser Printer Please read this manual thoroughly before using the printer Shipment of the Printer Laser Printer HL-1060 Series User’s Guide Compilation and Publication Notice Trademarks To Use the Printer Safely Definitions of Warnings, Cautions, and Notes Table of Contents Index Regulations Industry Canada Compliance Statement For Canada OnlyInternational Energy Star Compliance Statement Laser Safety For 110-120 V Model Only Radio Interference 220-240 V Model OnlyFDA Regulations For 110-120 V Model Only Declaration of Conformity For Europe IEC 825 Specification For 220-240 V Model Only Geräuschemission / Acoustic Noise Emission For Germany Only Important For Your Safety Important Wiring Information For U.K. only About the Guidebooks Finding Out How to Use the Printer Printer Overview About Your Printer Features Remote Printer Console Program for DOS Popular Printer Emulation SupportEnhanced Memory Management Environment-Friendly Economy Printing Mode Sleep Mode Power Save ModeLow Running Cost Power Supply Operating and Storage EnvironmentEnvironment Introduction Paper Type Paper Size Paper Specifications USER’S Guide Fan the Paper Straighten the Paper Remarks Envelopes MULTI-PURPOSE Sheet Feeders Opening the Feeder and Moving the Paper Guides Loading Paper into the Feeder Moving the Paper Guides Closing the Feeder Loading Paper in Feeder Two Side Printing Manual Duplexing When you load one sheet of paper manually When you load more than one sheet of paper manuallyManual Feed Slot Paper Handling You can stack up to 100 sheets in the output tray Output Tray and Paper Support Wire Ready Paper Lamp Lamps and Switch Data Toner Lamp Drum LampFeeder Lamp Sleep Mode Alarm LampSwitch Other Control Features Lamp Lit Choice Function Test Print Mode Protection Control Features Set by the Brother Driver APT Advanced Photoscale Technology Selecting the RS-422A Apple or RS-232C IBM Serial Interface Serial Interface Board RS100M Selecting the RS-422A Apple Or RS-232C IBM Serial Interface Setting the Serial Interface Parameters Off BitsBit DTR only None Connecting the Serial Interface Cable Options BR-SCRIPT 2 ROM Board BR-3000 Minimum Memory Recommendation including resident memory Additional Memory Unplug the power cord Disconnect the interface cable Installing the Simm Remove the main controller board Replacing the Toner Cartridge Chapter Maintenance Removing the Drum Unit Turning the Lever to Close the Shutter Removing the Old Toner Cartridge Installing the Toner Cartridge Into the Drum Unit Drum Unit Nearly at the End of its Life Replacing the Drum Unit 10 Removing the Drum Unit 12 Removing the Toner Cartridge ∙ Do not remove the starter sheet 15 Installing the Drum Unit 17 Adjusting the Print Density Dial Adjusting the Print Density Cleaning the Printer Exterior Cleaning the Printer 20 Turning off the Switch and Unplugging Cleaning the Printer Interior and Drum Unit Gently wipe the scanner window with a soft dry cloth 23 Cleaning the Primary Corona Wire 24 Cleaning the Feeder 1 Paper Feed Rollers Cleaning the Paper Feed Rollers RE-PACKING the Printer 26 Removing the Drum Unit Assembly 27 Placing the Drum Unit in the Plastic Bag Operator Calls Alarm Indications AT a Glance Simm Error Action Troubleshooting NV-RAM Service Calls Locating Paper Jam Position Paper Jams Paper Jam in the Feeders Paper Jam near the Drum Unit Do Not Pull the Jammed Paper from the Output Tray Question Recommendation Setting Up the Printer Hardware Question Setting Up the Printer for Windows Setting Up the Printer for DOS Setting Up the Printer for Apple Macintosh Computers When Using the Optional RS-100M Serial InterfaceWhen Using the Optional BR-Script 2 ROM Board BR-3000 Paper Handling Printing Together right now, over Print Quality Toner scatters and stains the printed Printer Interior and Drum Unit Appendix a Printer Specifications Functions Electrical and Mechanical Data Strobe Parallel Interface Specifications Fig. A-1 Parallel Interface Cable Intellifont Compatible Fonts Resident FontsBitmapped Fonts Scalable Fonts Appendix Epson Mode Symbol SETS/ Character SetsOCR Symbol Sets HP LaserJet 5P Mode Index Paper lamp 6-1