Error Action, Simm | Brother HL-1060 Series manual

USER’S GUIDE

For errors shown below, the printer indicates an operator call by blinking the Alarm lamp. If you use the printer with the supplied Windows driver, the status monitor will appear to indicate the error on your computer screen. The printer also prints some error messages on paper.

Error	Action
Cover Open	Close the top cover of the printer.

Print Overrun	∙ Press the panel switch to print the data remaining in the printer.
	∙ If you are using the supplied Windows driver, try again after
	changing the following settings. The best combination of the
	settings below will vary depending on your document.
	Graphics Mode
	TrueType™ Mode
	Use Printer True Type Fonts
	Page Protection
	∙ If this does not clear the error, reduce the complexity of your
	document or reduce the print resolution.
	∙ Expand the printer memory by installing a SIMM and set page
	protection to ON by using the supplied Windows driver or RPC
	program.

Memory Full	∙ Press the panel switch to print the data remaining in the printer.
	∙ If you are using the supplied Windows driver, try again after
	changing the following settings. The best combination of the
	settings below will vary depending on your document.
	Graphics Mode
	TrueType™ Mode
	Use Printer True Type Fonts
	Page Protection
	∙ Expand the printer memory by adding a commercially available
	SIMM.
	∙ Reduce the print resolution or reduce the complexity of your
	document.
Parallel Interface Line	∙ Press the panel switch to resume printing.
Error	∙ Check that the connection between your computer and printer
	is secure and correct, and check the interface cable.
Serial Interface Framing	∙ Press the panel switch to resume printing.
Error	∙ Check the communication parameters such as baud rate and
	stop bit on both your computer and printer.

Serial Interface Parity	∙ Press the panel switch to resume printing.
Error	∙ Check the communication parameters such as bit length and
	parity on both your computer and printer.

Serial Interface Overrun	∙ Press the panel switch to resume printing.
Error	∙ The interface hardware may be damaged. Consult your dealer.

CHAPTER 6 –2

Image 65

Brother HL-1060 Series manual Error Action, Simm

Contents

Brother Laser Printer Please read this manual thoroughly before using the printer Shipment of the Printer Laser Printer HL-1060 Series User’s Guide Compilation and Publication Notice Trademarks To Use the Printer Safely Definitions of Warnings, Cautions, and Notes Table of Contents Index International Energy Star Compliance Statement RegulationsIndustry Canada Compliance Statement For Canada Only FDA Regulations For 110-120 V Model Only Laser Safety For 110-120 V Model OnlyRadio Interference 220-240 V Model Only Declaration of Conformity For Europe IEC 825 Specification For 220-240 V Model Only Geräuschemission / Acoustic Noise Emission For Germany Only Important For Your Safety Important Wiring Information For U.K. only About the Guidebooks Finding Out How to Use the Printer Printer Overview About Your Printer Features Enhanced Memory Management Remote Printer Console Program for DOSPopular Printer Emulation Support Low Running Cost Environment-Friendly Economy Printing ModeSleep Mode Power Save Mode Environment Power SupplyOperating and Storage Environment Introduction Paper Type Paper Size Paper Specifications USER’S Guide Fan the Paper Straighten the Paper Remarks Envelopes MULTI-PURPOSE Sheet Feeders Opening the Feeder and Moving the Paper Guides Loading Paper into the Feeder Moving the Paper Guides Closing the Feeder Loading Paper in Feeder Two Side Printing Manual Duplexing Manual Feed Slot When you load one sheet of paper manuallyWhen you load more than one sheet of paper manually Paper Handling You can stack up to 100 sheets in the output tray Output Tray and Paper Support Wire Ready Paper Lamp Lamps and Switch Feeder Lamp Data Toner LampDrum Lamp Switch Alarm LampOther Control Features Sleep Mode Lamp Lit Choice Function Test Print Mode Protection Control Features Set by the Brother Driver APT Advanced Photoscale Technology Selecting the RS-422A Apple or RS-232C IBM Serial Interface Serial Interface Board RS100M Selecting the RS-422A Apple Or RS-232C IBM Serial Interface Setting the Serial Interface Parameters Bit BitsDTR only Off None Connecting the Serial Interface Cable Options BR-SCRIPT 2 ROM Board BR-3000 Minimum Memory Recommendation including resident memory Additional Memory Unplug the power cord Disconnect the interface cable Installing the Simm Remove the main controller board Replacing the Toner Cartridge Chapter Maintenance Removing the Drum Unit Turning the Lever to Close the Shutter Removing the Old Toner Cartridge Installing the Toner Cartridge Into the Drum Unit Drum Unit Nearly at the End of its Life Replacing the Drum Unit 10 Removing the Drum Unit 12 Removing the Toner Cartridge ∙ Do not remove the starter sheet 15 Installing the Drum Unit 17 Adjusting the Print Density Dial Adjusting the Print Density Cleaning the Printer Exterior Cleaning the Printer 20 Turning off the Switch and Unplugging Cleaning the Printer Interior and Drum Unit Gently wipe the scanner window with a soft dry cloth 23 Cleaning the Primary Corona Wire 24 Cleaning the Feeder 1 Paper Feed Rollers Cleaning the Paper Feed Rollers RE-PACKING the Printer 26 Removing the Drum Unit Assembly 27 Placing the Drum Unit in the Plastic Bag Operator Calls Alarm Indications AT a Glance Simm Error Action Troubleshooting NV-RAM Service Calls Locating Paper Jam Position Paper Jams Paper Jam in the Feeders Paper Jam near the Drum Unit Do Not Pull the Jammed Paper from the Output Tray Question Recommendation Setting Up the Printer Hardware Question Setting Up the Printer for Windows Setting Up the Printer for DOS When Using the Optional BR-Script 2 ROM Board BR-3000 Setting Up the Printer for Apple Macintosh ComputersWhen Using the Optional RS-100M Serial Interface Paper Handling Printing Together right now, over Print Quality Toner scatters and stains the printed Printer Interior and Drum Unit Appendix a Printer Specifications Functions Electrical and Mechanical Data Strobe Parallel Interface Specifications Fig. A-1 Parallel Interface Cable Bitmapped Fonts Resident FontsScalable Fonts Intellifont Compatible Fonts Appendix OCR Symbol Sets Symbol SETS/ Character SetsHP LaserJet 5P Mode Epson Mode Index Paper lamp 6-1