Setting Up the Printer Hardware | Brother HL-1060 Series specification

CHAPTER 6 TROUBLESHOOTING

Q & A

This section contains questions and answers for using your printer. If you have encountered a problem, find the question relating to your problem and take the steps recommended to correct the problem.

Setting Up the Printer Hardware

Question	Recommendation
The printer does not work. All	The printer may be in sleep mode. Press the panel
lamps are off.	switch to wake up the printer. Check to see if the
	printer is plugged into a live power source and the
	power switch is on.

The printer does not print.	Check the following:
	∙ The printer is turned on.
	∙ All of the protective parts have been removed.
	∙ The toner cartridge and drum unit are installed
	properly.
	∙ The interface cable is securely connected between
	the printer and computer.
	∙ Check to see if the Alarm lamp is blinking. If the
	lamp is blinking, refer to the Operator Call section
	of this manual.
	∙ Check to see if the Ready lamp is blinking. If the
	lamp is blinking fast, the printer might be cooling
	down to lower the printers internal temperature.
	Open the top cover of the printer to lower the
	temperature.

CHAPTER 6 –9

Image 72

Brother HL-1060 Series manual Setting Up the Printer Hardware, Question Recommendation

Contents

Please read this manual thoroughly before using the printer Brother Laser Printer Shipment of the Printer Laser Printer HL-1060 Series User’s Guide Trademarks Compilation and Publication Notice Definitions of Warnings, Cautions, and Notes To Use the Printer Safely Table of Contents Index Regulations Industry Canada Compliance Statement For Canada OnlyInternational Energy Star Compliance Statement Laser Safety For 110-120 V Model Only Radio Interference 220-240 V Model OnlyFDA Regulations For 110-120 V Model Only IEC 825 Specification For 220-240 V Model Only Declaration of Conformity For Europe Important For Your Safety Geräuschemission / Acoustic Noise Emission For Germany Only Important Wiring Information For U.K. only Finding Out How to Use the Printer About the Guidebooks About Your Printer Printer Overview Features Remote Printer Console Program for DOS Popular Printer Emulation SupportEnhanced Memory Management Environment-Friendly Economy Printing Mode Sleep Mode Power Save ModeLow Running Cost Power Supply Operating and Storage EnvironmentEnvironment Introduction Paper Specifications Paper Type Paper Size USER’S Guide Remarks Fan the Paper Straighten the Paper Envelopes MULTI-PURPOSE Sheet Feeders Loading Paper into the Feeder Opening the Feeder and Moving the Paper Guides Moving the Paper Guides Closing the Feeder Loading Paper in Feeder Two Side Printing Manual Duplexing When you load one sheet of paper manually When you load more than one sheet of paper manuallyManual Feed Slot Paper Handling Output Tray and Paper Support Wire You can stack up to 100 sheets in the output tray Lamps and Switch Ready Paper Lamp Data Toner Lamp Drum LampFeeder Lamp Alarm Lamp SwitchOther Control Features Sleep Mode Test Print Mode Lamp Lit Choice Function Control Features Set by the Brother Driver Protection APT Advanced Photoscale Technology Serial Interface Board RS100M Selecting the RS-422A Apple or RS-232C IBM Serial Interface Setting the Serial Interface Parameters Selecting the RS-422A Apple Or RS-232C IBM Serial Interface Bits BitDTR only Off Connecting the Serial Interface Cable None Options BR-SCRIPT 2 ROM Board BR-3000 Additional Memory Minimum Memory Recommendation including resident memory Installing the Simm Unplug the power cord Disconnect the interface cable Remove the main controller board Chapter Maintenance Replacing the Toner Cartridge Removing the Drum Unit Turning the Lever to Close the Shutter Removing the Old Toner Cartridge Installing the Toner Cartridge Into the Drum Unit Replacing the Drum Unit Drum Unit Nearly at the End of its Life 10 Removing the Drum Unit ∙ Do not remove the starter sheet 12 Removing the Toner Cartridge 15 Installing the Drum Unit Adjusting the Print Density 17 Adjusting the Print Density Dial Cleaning the Printer Cleaning the Printer Exterior Cleaning the Printer Interior and Drum Unit 20 Turning off the Switch and Unplugging Gently wipe the scanner window with a soft dry cloth 23 Cleaning the Primary Corona Wire Cleaning the Paper Feed Rollers 24 Cleaning the Feeder 1 Paper Feed Rollers 26 Removing the Drum Unit Assembly RE-PACKING the Printer 27 Placing the Drum Unit in the Plastic Bag Alarm Indications AT a Glance Operator Calls Error Action Simm Troubleshooting Service Calls NV-RAM Paper Jams Locating Paper Jam Position Paper Jam in the Feeders Paper Jam near the Drum Unit Do Not Pull the Jammed Paper from the Output Tray Setting Up the Printer Hardware Question Recommendation Setting Up the Printer for Windows Question Setting Up the Printer for DOS Setting Up the Printer for Apple Macintosh Computers When Using the Optional RS-100M Serial InterfaceWhen Using the Optional BR-Script 2 ROM Board BR-3000 Paper Handling Printing Print Quality Together right now, over Toner scatters and stains the printed Printer Interior and Drum Unit Printer Specifications Appendix a Functions Electrical and Mechanical Parallel Interface Specifications Data Strobe Fig. A-1 Parallel Interface Cable Resident Fonts Bitmapped FontsScalable Fonts Intellifont Compatible Fonts Appendix Symbol SETS/ Character Sets OCR Symbol SetsHP LaserJet 5P Mode Epson Mode Index Paper lamp 6-1