Setting Up the Printer for Windows | Brother HL-1060 Series specs

USER’S GUIDE

Setting Up the Printer for Windows

Question

I cannot print from my application software.

Sometimes I get a Print Overrun error when printing certain documents from Windows.

Sometimes I get the Memory Full message. How can I correct this?

Recommendation

∙Make sure the supplied Windows printer driver is installed and selected with your application software.

∙If you use the serial interface, make sure that the serial slide switch of the serial interface is in the correct position and the interface settings are correctly set up with the DIP switches.

∙Change the following settings in the driver and try again.

Page Protection Graphics Mode TrueType™ Mode

Use Printer TrueType™ Fonts

∙Reduce the print resolution or reduce the complexity of your document and try again.

∙Expand the printer memory by installing SIMM and turn page protection A4, Letter or Legal to ON through the supplied Windows driver or RPC.

∙Change the following settings in the driver and try again.

Page Protection Graphics Mode TrueType™ Mode

Use Printer TrueType™ Fonts

∙Another solution is to purchase more memory.

∙Reduce the print resolution or reduce the complexity of your document and try again.

CHAPTER 6 –10

Image 73

Brother HL-1060 Series manual Setting Up the Printer for Windows, Question

Contents

Brother Laser Printer Please read this manual thoroughly before using the printer Shipment of the Printer Laser Printer HL-1060 Series User’s Guide Compilation and Publication Notice Trademarks To Use the Printer Safely Definitions of Warnings, Cautions, and Notes Table of Contents Index Industry Canada Compliance Statement For Canada Only RegulationsInternational Energy Star Compliance Statement Radio Interference 220-240 V Model Only Laser Safety For 110-120 V Model OnlyFDA Regulations For 110-120 V Model Only Declaration of Conformity For Europe IEC 825 Specification For 220-240 V Model Only Geräuschemission / Acoustic Noise Emission For Germany Only Important For Your Safety Important Wiring Information For U.K. only About the Guidebooks Finding Out How to Use the Printer Printer Overview About Your Printer Features Popular Printer Emulation Support Remote Printer Console Program for DOSEnhanced Memory Management Sleep Mode Power Save Mode Environment-Friendly Economy Printing ModeLow Running Cost Operating and Storage Environment Power SupplyEnvironment Introduction Paper Type Paper Size Paper Specifications USER’S Guide Fan the Paper Straighten the Paper Remarks Envelopes MULTI-PURPOSE Sheet Feeders Opening the Feeder and Moving the Paper Guides Loading Paper into the Feeder Moving the Paper Guides Closing the Feeder Loading Paper in Feeder Two Side Printing Manual Duplexing When you load more than one sheet of paper manually When you load one sheet of paper manuallyManual Feed Slot Paper Handling You can stack up to 100 sheets in the output tray Output Tray and Paper Support Wire Ready Paper Lamp Lamps and Switch Drum Lamp Data Toner LampFeeder Lamp Switch Alarm LampOther Control Features Sleep Mode Lamp Lit Choice Function Test Print Mode Protection Control Features Set by the Brother Driver APT Advanced Photoscale Technology Selecting the RS-422A Apple or RS-232C IBM Serial Interface Serial Interface Board RS100M Selecting the RS-422A Apple Or RS-232C IBM Serial Interface Setting the Serial Interface Parameters Bit BitsDTR only Off None Connecting the Serial Interface Cable Options BR-SCRIPT 2 ROM Board BR-3000 Minimum Memory Recommendation including resident memory Additional Memory Unplug the power cord Disconnect the interface cable Installing the Simm Remove the main controller board Replacing the Toner Cartridge Chapter Maintenance Removing the Drum Unit Turning the Lever to Close the Shutter Removing the Old Toner Cartridge Installing the Toner Cartridge Into the Drum Unit Drum Unit Nearly at the End of its Life Replacing the Drum Unit 10 Removing the Drum Unit 12 Removing the Toner Cartridge ∙ Do not remove the starter sheet 15 Installing the Drum Unit 17 Adjusting the Print Density Dial Adjusting the Print Density Cleaning the Printer Exterior Cleaning the Printer 20 Turning off the Switch and Unplugging Cleaning the Printer Interior and Drum Unit Gently wipe the scanner window with a soft dry cloth 23 Cleaning the Primary Corona Wire 24 Cleaning the Feeder 1 Paper Feed Rollers Cleaning the Paper Feed Rollers RE-PACKING the Printer 26 Removing the Drum Unit Assembly 27 Placing the Drum Unit in the Plastic Bag Operator Calls Alarm Indications AT a Glance Simm Error Action Troubleshooting NV-RAM Service Calls Locating Paper Jam Position Paper Jams Paper Jam in the Feeders Paper Jam near the Drum Unit Do Not Pull the Jammed Paper from the Output Tray Question Recommendation Setting Up the Printer Hardware Question Setting Up the Printer for Windows Setting Up the Printer for DOS When Using the Optional RS-100M Serial Interface Setting Up the Printer for Apple Macintosh ComputersWhen Using the Optional BR-Script 2 ROM Board BR-3000 Paper Handling Printing Together right now, over Print Quality Toner scatters and stains the printed Printer Interior and Drum Unit Appendix a Printer Specifications Functions Electrical and Mechanical Data Strobe Parallel Interface Specifications Fig. A-1 Parallel Interface Cable Bitmapped Fonts Resident FontsScalable Fonts Intellifont Compatible Fonts Appendix OCR Symbol Sets Symbol SETS/ Character SetsHP LaserJet 5P Mode Epson Mode Index Paper lamp 6-1