Declaration of Conformity For Europe | Brother HL-760 Series

USER’S GUIDE

Declaration of Conformity (For Europe)

We, Brother International Europe Ltd.,

Brother House 1 Tame Street, Guide Bridge, Audenshaw, Manchester M34 5JE, UK.

declare that this product is in conformity with the following normative documents.

Safety:	EN 60950,	EN 60825
EMC:	EN 55022 Class B,	EN 50082-1

following the provisions of the Low Voltage Directive 73/23/EEC and the Electromagnetic Compatibility Directive 89/336/EEC (as amended by 91/263/EEC and 92/31/EEC).

Issued by:

Brother International Europe Ltd.

European Technical Services Division

IEC 825 Specification (For 220–240 V Model Only)

This printer is a Class 1 laser product as defined in IEC 825 specifications. The label shown below is attached in countries where required.

This printer has a Class 3B Laser Diode which emits invisible laser radiation in the Scanner Unit. The Scanner Unit should not be opened under any circumstances.

Caution

Use of controls, adjustments or performance of procedures other than those specified in this manual may result in hazardous radiation exposure.

The following caution label is attached near the scanner unit.

viii

Image 10

Brother HL-760 Series manual Declaration of Conformity For Europe, IEC 825 Specification For 220-240 V Model Only

Contents

Please read this manual thoroughly before using the printer Brother Laser Printer Shipment of the Printer Laser Printer HL-760 Series User’s Guide Trademarks Compilation and Publication Notice Definitions of Warnings, Cautions, and Notes To Use the Printer Safely Table of Contents Index Industry Canada Compliance Statement For Canada Only RegulationsInternational Energy Star Compliance Statement Radio Interference 220-240 V Model Only Laser Safety For 110-120 V Model OnlyFDA Regulations For 110-120 V Model Only IEC 825 Specification For 220-240 V Model Only Declaration of Conformity For Europe Important For Your Safety Geräuschemission / Acoustic Noise Emission For Germany Only Important Wiring Information For U.K. only Finding Out How to Use the Printer About the Guidebooks About Your Printer Printer Overview Dpi Resolution and 6 ppm Printing Speed FeaturesVersatile Paper Handling Popular Printer Emulation Support Remote Printer Console Program for DOSOptional Apple Macintosh Interface Enhanced Memory Management Environment-Friendly Economy Printing ModeSleep Mode Power Save Mode Low Running Cost Operating and Storage Environment Power SupplyEnvironment Introduction Paper Specifications Paper Type Paper Size Remarks Fan the Paper Straighten the Paper Envelopes MULTI-PURPOSE Sheet Feeder Loading Paper into the Feeder Opening the Feeder Loading Paper or Envelopes in the Feeder Paper Jams in Chapter Two Side Printing Manual Duplexing When you load more than one sheet of paper manually When you load one sheet of paper manuallyManual Feed Slot Paper Handling Output Tray and Paper Support Wire Opening the Output Tray Extending the Extension Support Wire Lamps and Switch Ready Paper Lamp Data Toner Lamp Alarm LampDrum Lamp Switch Other Control FeaturesSleep Mode Test Print Mode Lamp Lit Choice Function Control Features Set by the Brother Printer Driver Protection Serial Interface Board RS-100M Selecting the RS-422A Apple or RS-232C IBM Serial Interface Setting the Serial Interface Parameters Selecting the RS-422A Apple Or RS-232C IBM Serial Interface DTR only BitsBit Off Connecting the Serial Interface Cable None Options Additional Memory Minimum Memory Recommendation including resident memory Installing the Simm Unplug the Power Cord Disconnect the Interface Cable Removing the Main Controller Board Chapter Maintenance Replacing the Toner Cartridge Removing the Drum Unit Turning the Lever to Close the Shutter Removing the Old Toner Cartridge Installing the Toner Cartridge Into the Drum Unit Replacing the Drum Unit Drum Unit Nearly at the End of its Life 10 Removing the Drum Unit ∙ Do not remove the starter sheet 12 Removing the Toner Cartridge 15 Installing the Drum Unit Adjusting the Print Density 17 Adjusting the Print Density Dial Cleaning the Printer Cleaning the Printer Exterior Cleaning the Printer Interior and Drum Unit 20 Turning off the Switch and Unplugging Gently wipe the scanner window with a soft dry cloth 23 Cleaning the Primary Corona Wire 24 Removing the Drum Unit Assembly RE-PACKING the Printer 25 Placing the Drum Unit in the Plastic Bag Blinking Lamp Error Action Alarm Indications AT a GlanceOperator Calls Error Action Troubleshooting Service Calls Paper Jams Locating Paper Jam Position Do Not Pull the Jammed Paper from the Output Tray Paper Jam near the Drum Unit Setting Up the Printer for Windows Setting Up the Printer HardwareQuestion Recommendation Setting Up the Printer for DOS Question Paper Handling Printing Serial Inter Face Board RS100M Print Quality White Stripes or Faint Images Toner scatters and stains the printed Printed pages are blurred at the center or either edge Printer Specifications Appendix a Functions Electrical and Mechanical Parallel Interface Specifications Data Strobe Fig. A-1 Parallel Interface Cable Scalable Fonts Resident FontsBitmapped Fonts Intellifont Compatible Fonts HP LaserJet 5P Mode Symbol SETS/CHARACTER SetsOCR Symbol Sets Epson Mode Index Slide switch