RE-PACKING the Printer | Brother HL-760 Series specification

CHAPTER 5 MAINTENANCE

RE-PACKING THE PRINTER

!Caution

Whenever you transport the printer, use the packing materials which are provided with your printer. Also, follow the steps below to re-pack the printer, or the printer may be damaged which will void the printer’s warranty.

1.Turn off the power switch and unplug the printer from the AC outlet.

2.Open the top cover.

3.Remove the drum unit assembly, referring to the previous section.

✒Note

Remove the drum unit assembly with the toner cartridge included.

Fig. 5-24 Removing the Drum Unit Assembly

CHAPTER 5 –15

Image 57

Brother HL-760 Series manual RE-PACKING the Printer, Removing the Drum Unit Assembly

Contents

Brother Laser Printer Please read this manual thoroughly before using the printer Shipment of the Printer Laser Printer HL-760 Series User’s Guide Compilation and Publication Notice Trademarks To Use the Printer Safely Definitions of Warnings, Cautions, and Notes Table of Contents Index Regulations Industry Canada Compliance Statement For Canada OnlyInternational Energy Star Compliance Statement Laser Safety For 110-120 V Model Only Radio Interference 220-240 V Model OnlyFDA Regulations For 110-120 V Model Only Declaration of Conformity For Europe IEC 825 Specification For 220-240 V Model Only Geräuschemission / Acoustic Noise Emission For Germany Only Important For Your Safety Important Wiring Information For U.K. only About the Guidebooks Finding Out How to Use the Printer Printer Overview About Your Printer Features Dpi Resolution and 6 ppm Printing SpeedVersatile Paper Handling Remote Printer Console Program for DOS Popular Printer Emulation SupportOptional Apple Macintosh Interface Sleep Mode Power Save Mode Environment-Friendly Economy Printing ModeEnhanced Memory Management Low Running Cost Power Supply Operating and Storage EnvironmentEnvironment Introduction Paper Type Paper Size Paper Specifications Fan the Paper Straighten the Paper Remarks Envelopes MULTI-PURPOSE Sheet Feeder Opening the Feeder Loading Paper or Envelopes in the Feeder Loading Paper into the Feeder Paper Jams in Chapter Two Side Printing Manual Duplexing When you load one sheet of paper manually When you load more than one sheet of paper manuallyManual Feed Slot Paper Handling Opening the Output Tray Extending the Extension Support Wire Output Tray and Paper Support Wire Ready Paper Lamp Lamps and Switch Alarm Lamp Data Toner LampDrum Lamp Other Control Features SwitchSleep Mode Lamp Lit Choice Function Test Print Mode Protection Control Features Set by the Brother Printer Driver Selecting the RS-422A Apple or RS-232C IBM Serial Interface Serial Interface Board RS-100M Selecting the RS-422A Apple Or RS-232C IBM Serial Interface Setting the Serial Interface Parameters Bit BitsDTR only Off None Connecting the Serial Interface Cable Options Minimum Memory Recommendation including resident memory Additional Memory Unplug the Power Cord Disconnect the Interface Cable Installing the Simm Removing the Main Controller Board Replacing the Toner Cartridge Chapter Maintenance Removing the Drum Unit Turning the Lever to Close the Shutter Removing the Old Toner Cartridge Installing the Toner Cartridge Into the Drum Unit Drum Unit Nearly at the End of its Life Replacing the Drum Unit 10 Removing the Drum Unit 12 Removing the Toner Cartridge ∙ Do not remove the starter sheet 15 Installing the Drum Unit 17 Adjusting the Print Density Dial Adjusting the Print Density Cleaning the Printer Exterior Cleaning the Printer 20 Turning off the Switch and Unplugging Cleaning the Printer Interior and Drum Unit Gently wipe the scanner window with a soft dry cloth 23 Cleaning the Primary Corona Wire RE-PACKING the Printer 24 Removing the Drum Unit Assembly 25 Placing the Drum Unit in the Plastic Bag Alarm Indications AT a Glance Blinking Lamp Error ActionOperator Calls Error Action Troubleshooting Service Calls Locating Paper Jam Position Paper Jams Do Not Pull the Jammed Paper from the Output Tray Paper Jam near the Drum Unit Setting Up the Printer Hardware Setting Up the Printer for WindowsQuestion Recommendation Question Setting Up the Printer for DOS Paper Handling Serial Inter Face Board RS100M Printing White Stripes or Faint Images Print Quality Toner scatters and stains the printed Printed pages are blurred at the center or either edge Appendix a Printer Specifications Functions Electrical and Mechanical Data Strobe Parallel Interface Specifications Fig. A-1 Parallel Interface Cable Bitmapped Fonts Resident FontsScalable Fonts Intellifont Compatible Fonts OCR Symbol Sets Symbol SETS/CHARACTER SetsHP LaserJet 5P Mode Epson Mode Index Slide switch