Error Action | Brother HL-760 Series manual

USER’S GUIDE

For errors shown below, the printer indicates an operator call by blinking the Alarm lamp. If you use the printer with the supplied Windows driver, the status monitor will appear to indicate the error on your computer screen. The printer may also print some error messages.

Error	Action
Cover Open	Close the top cover of the printer.
Memory Full	∙ Press the panel switch to print the data remaining in the printer.
	∙ If you are using the supplied Windows driver, try again after
	changing the following settings. The best combination of the
	settings below will vary depending on your document.
	Graphics Mode
	TrueType mode
	Use Printer True Type Fonts
	Page Protection
	∙ Expand the printer memory by adding a commercially
	available SIMM.
	∙ Reduce the print resolution or reduce the complexity of your
	document.
Print Overrun	∙ Press the panel switch to print the data remaining in the printer.
	∙ If you are using the supplied Windows driver, try again after
	changing the following settings. The best combination of the
	settings below will vary depending on your document.
	Graphics Mode
	TrueType mode
	Use Printer True Type Fonts
	Page Protection
	∙ If this does not clear the error, reduce the complexity of your
	document or reduce the print resolution.
	∙ Expand the printer memory by installing SIMM and set page
	protection to ON by using the supplied Windows driver or
	RPC program.
Parallel Interface Line	∙ Press the panel switch to resume printing.
Error	∙ Check that the connection between your computer and printer is
	secure and correct, and check the interface cable.
Serial Interface Framing	∙ Press the panel switch to resume printing.
Error	∙ Check the communication parameters such as baud rate and stop
	bit on both your computer and printer.

Serial Interface Parity	∙ Press the panel switch to resume printing.
Error	∙ Check the communication parameters such as bit length and
	parity on both your computer and printer.

Serial Interface Overrun	∙ Press the panel switch to resume printing.
Error	∙ The interface hardware may be damaged. Consult your dealer.

CHAPTER 6 –2

Image 60

Brother HL-760 Series manual Error Action

Contents

Please read this manual thoroughly before using the printer Brother Laser Printer Shipment of the Printer Laser Printer HL-760 Series User’s Guide Trademarks Compilation and Publication Notice Definitions of Warnings, Cautions, and Notes To Use the Printer Safely Table of Contents Index Regulations Industry Canada Compliance Statement For Canada OnlyInternational Energy Star Compliance Statement Laser Safety For 110-120 V Model Only Radio Interference 220-240 V Model OnlyFDA Regulations For 110-120 V Model Only IEC 825 Specification For 220-240 V Model Only Declaration of Conformity For Europe Important For Your Safety Geräuschemission / Acoustic Noise Emission For Germany Only Important Wiring Information For U.K. only Finding Out How to Use the Printer About the Guidebooks About Your Printer Printer Overview Features Dpi Resolution and 6 ppm Printing SpeedVersatile Paper Handling Remote Printer Console Program for DOS Popular Printer Emulation SupportOptional Apple Macintosh Interface Environment-Friendly Economy Printing Mode Sleep Mode Power Save ModeEnhanced Memory Management Low Running Cost Power Supply Operating and Storage EnvironmentEnvironment Introduction Paper Specifications Paper Type Paper Size Remarks Fan the Paper Straighten the Paper Envelopes MULTI-PURPOSE Sheet Feeder Loading Paper into the Feeder Opening the Feeder Loading Paper or Envelopes in the Feeder Paper Jams in Chapter Two Side Printing Manual Duplexing When you load one sheet of paper manually When you load more than one sheet of paper manuallyManual Feed Slot Paper Handling Output Tray and Paper Support Wire Opening the Output Tray Extending the Extension Support Wire Lamps and Switch Ready Paper Lamp Alarm Lamp Data Toner LampDrum Lamp Other Control Features SwitchSleep Mode Test Print Mode Lamp Lit Choice Function Control Features Set by the Brother Printer Driver Protection Serial Interface Board RS-100M Selecting the RS-422A Apple or RS-232C IBM Serial Interface Setting the Serial Interface Parameters Selecting the RS-422A Apple Or RS-232C IBM Serial Interface Bits BitDTR only Off Connecting the Serial Interface Cable None Options Additional Memory Minimum Memory Recommendation including resident memory Installing the Simm Unplug the Power Cord Disconnect the Interface Cable Removing the Main Controller Board Chapter Maintenance Replacing the Toner Cartridge Removing the Drum Unit Turning the Lever to Close the Shutter Removing the Old Toner Cartridge Installing the Toner Cartridge Into the Drum Unit Replacing the Drum Unit Drum Unit Nearly at the End of its Life 10 Removing the Drum Unit ∙ Do not remove the starter sheet 12 Removing the Toner Cartridge 15 Installing the Drum Unit Adjusting the Print Density 17 Adjusting the Print Density Dial Cleaning the Printer Cleaning the Printer Exterior Cleaning the Printer Interior and Drum Unit 20 Turning off the Switch and Unplugging Gently wipe the scanner window with a soft dry cloth 23 Cleaning the Primary Corona Wire 24 Removing the Drum Unit Assembly RE-PACKING the Printer 25 Placing the Drum Unit in the Plastic Bag Alarm Indications AT a Glance Blinking Lamp Error ActionOperator Calls Error Action Troubleshooting Service Calls Paper Jams Locating Paper Jam Position Do Not Pull the Jammed Paper from the Output Tray Paper Jam near the Drum Unit Setting Up the Printer Hardware Setting Up the Printer for WindowsQuestion Recommendation Setting Up the Printer for DOS Question Paper Handling Printing Serial Inter Face Board RS100M Print Quality White Stripes or Faint Images Toner scatters and stains the printed Printed pages are blurred at the center or either edge Printer Specifications Appendix a Functions Electrical and Mechanical Parallel Interface Specifications Data Strobe Fig. A-1 Parallel Interface Cable Resident Fonts Bitmapped FontsScalable Fonts Intellifont Compatible Fonts Symbol SETS/CHARACTER Sets OCR Symbol SetsHP LaserJet 5P Mode Epson Mode Index Slide switch