Bryant 548D installation instructions Base Unit Dimensions

	STD UNIT		DURABLADE		ECONOMI$ER		CORNER			CORNER			CORNER			CORNER
UNIT			ECONOMIZER				WEIGHT			WEIGHT			WEIGHT			WEIGHT			“H”		“J”		“K”
	WEIGHT				WEIGHT
548D			WEIGHT					(A)			(B)			(C)			(D)
	Lb	Kg	Lb	Kg	Lb	Kg	Lb		Kg	Lb		Kg	Lb		Kg	Lb		Kg	Ft-in.	mm	Ft-in.	mm	Ft-in.	mm
090	940	426	44	20	62	28	207		94	178		81	254		115	301		136	2- 07/8	632	3-55/16	1050	2-911/16	856
102	965	438	44	20	62	28	212		96	183		83	261		119	309		140	2- 07/8	632	3-55/16	1050	2-911/16	856
120	1015	460	44	20	62	28	223		101	193		88	274		124	325		147	2-107/8	885	4-15/16	1253	3-03/8	924

BOTTOM POWER CHART, THESE HOLES REQ’D

FOR USE WITH ACCESSORY PACKAGES —

CRBTMPWR001A00 (1/2″, 3/4″) OR

CRBTMPWR002A00 (1/2″, 11/4″)

THREADED	WIRE	REQ’D HOLE
CONDUIT		SIZES
	USE
SIZE		(Max.)
1/2″	24 V	7/8″ [22.2]

NOTES:

1.	Dimensions in [ ] are in millimeters.
2.	Center of gravity.

3.Direction of airflow.

4.Ductwork to be attached to accessory roof curb only.

5.Minimum clearance (local codes or jurisdiction may prevail):

a.Bottom to combustible surfaces (when not using curb) 0 inches, on horizontal discharge units with electric heat 1 in. clearance to ductwork for 1 ft.

b.Condenser coil, for proper airflow, 36 in. one side, 12 in. the other. The side getting the greater clearance is optional.

c.Overhead, 60 in. to assure proper condenser fan operation.

d.Between units, control box side, 42 in. per NEC (National Electri- cal Code).

e.Between unit and ungrounded surfaces, control box side, 36 in. per NEC.

f.Between unit and block or concrete walls and other grounded surfaces, control box side, 42 in. per NEC.

g.Horizontal supply and return end, 0 inches.

6.With the exception of the clearance for the condenser coil as stated in Notes 5a, b, and c, a removable fence or barricade requires no clearance.

7.Units may be installed on combustible floors made from wood or Class A, B, or C roof covering material.

8.The vertical center of gravity is 1′-71/2″[495] for 090 and 102, 2′-0″

[610]for 120 up from the bottom of the base rail.

—5—

		CONNECTION SIZES
A		13/8″ Dia. [35]	Field Power Supply Hole
B		21/2″ Dia. [64]	Power Supply Knockout
C		13/4″ Dia. [44]	Charging Port Hole
D		7/8″ Dia. [22] Field Control Wiring Hole
E		3/4″ — 14 NPT Condensate Drain
F	2″ Dia. [51] Power Supply Knockout

3/4″	Power*	11/8″ [28.4]
11/4″ FPT	Power*	13/4″ [44.4]

*Select either 3/4″ or 11/4″ for power, depending on wire size.

Fig. 6 — Base Unit Dimensions