Manuals / Bunn / Kitchen Appliance / Coffeemaker

Bunn JDF-4S SERVICE CONT Lamps, Holders and Ballasts Early Models, Lamps & Holders, Lamp Holders

Models: JDF-4D JDF-4SB JDF-4S

1 57

Download 57 pages 43.05 Kb

Page 39

SERVICE (CONT.)

SERVICE (CONT.)

Lamps, Holders and Ballast(s) (Early Models)

FIG. 51 LAMPS & HOLDERS

Location:

The lamps and lamp holders are located on the door light panel behind the door cover.

Test Procedure:

1.Disconnect the dispenser from the power source.

2.Remove the five #10-32 screws securing the door cover to the door and move the cover aside to gain access to the light panel.

3.Rotate the lamp to remove from the lamp hold- ers.

4.Check for continuity across terminals on each end of the lamp.

If continuity is present as described, continue to step 5. If continuity is not present as described replace the lamp.

5.Check for 24VDC supplied to ballast (dual ballast black to red, single ballast white to red).

If voltage is present as described, replace ballast. If voltage is not present as described, refer to the Wiring Diagrams and check the wiring harness back to the transfomer/rectifier.

Removal and Replacement:

1.Disconnect the dispenser from the power source.

2.Remove the five #10-32 screws securing the door cover to the door and move the cover aside to gain access to the light panel.

3.Rotate the lamp to remove from the lamp hold- ers.

4.Pry the lamp holder from light panel.

5.Cut the two wires from the ballast as close the lamp holder as possible and remove the lamp holder.

6.Strip the ends of the wires from the ballast and install the into the new lamp holder.

7.Snap the new lamp holder into the holes on the light panel.

8.Replace the lamps and install the door cover using the five screws previously removed.

FIG. 52 LAMP HOLDERS

39	49179	110613

Image 39

Bunn JDF-4SB, JDF-4D manual SERVICE CONT Lamps, Holders and Ballasts Early Models, Lamps & Holders, Lamp Holders

Contents

49179.0000C 02/14 2013 Bunn-O-Matic Corporation SERVICE & REPAIR MANUALJDF-2S, JDF-4S JDF-4D, JDF-4SB BUNN-O-MATIC CORPORATIONBUNN-O-MATIC COMMERCIAL PRODUCT WARRANTY Preventive Maintenance CONTENTSSafety first Basic MaintenanceRecommended Daily Cleaning Instructions REQUIRED REGULAR MAINTENANCE Cold Water Circulation TROUBLESHOOTINGPROBLEM PROBABLE CAUSEPROBLEM TROUBLESHOOTING ContinuedRefrigeration Dispenser Locked OutREMEDY TROUBLESHOOTING ContinuedPROBLEM PROBABLE CAUSEPROBLEM concentrate onlywater only TROUBLESHOOTING ContinuedPROBABLE CAUSE TROUBLESHOOTING ContinuedPROBLEM 1. Initial fill/setupPROBABLE CAUSE TROUBLESHOOTING ContinuedPROBLEM from bag-in-box connector to bottleCOMPONENT ACCESS SERVICE49179 SERVICECONT ACCESS PANELSFIG. 1 ACCESS PANELS JDF-4S shownThe JDF-4S uses 2 of the two head dispense platforms SERVICECONT DISPENSE PLATFORM REMOVALSERVICE CONT Ballast JDF-2S,4S FIG. 3 BALLASTLocation SERVICE CONT Cabinet Fan all Models LocationFIG. 5 CABINET FAN GRN Wire SERVICE CONT LG Compressor JDF-2S,4S,4DSERVICE CONT Compressor Cont FIG.12 COMPRESSOR THERMAL SERVICE CONT GD Compressor JDF-2S,4S,4DFIG. 11 COMPRESSOR LocationSERVICE CONT Compressor Cont BLU/BLK GRN WHIPlugs into Relay 230V shown SERVICE CONT Compressor JDF-4SBBRN from Capacitor SERVICE CONT Compressor ContBLU/BLK BLU from CapacitorRED/BLK BLK SERVICE CONT Compressor Switch all ModelsFIG. 19 COMPRESSOR SWITCH LocationBLU/BLK SERVICE CONT Condenser Fan all ModelsFIG. 21 CONDENSER FAN LocationSERVICE CONT Control Board, Main all Models Disconnect the dispenser from the power source SERVICE CONT Portion Control Board JDF-2S,4SFIG. 28 CONTROL BOARD CONNECTORS SERVICE CONT Push Button Control Board JDF-4DPortion Control Board JDF-4D SERVICE CONTSERVICE CONT Circulation Pump all Models FIG. 33 DISPENSE PLATFORM SWITCH SERVICE CONT Dispense Platform Switch all ModelsSERVICE CONT Dispense Pump all Models except JDF-4D SERVICE CONT Dispense Motor all Models FIG. 38 DISPENSE MOTOR CONNECTORSFIG. 37 DISPENSE MOTOR #3 WHI/VIO Dispense Station #4 WHI/ORN YEL to Control Board SERVICE CONT Dispense Valve all ModelsFIG. 39 DISPENSE VALVE Dispense Station #1 WHI/VIOP1449 SERVICE CONT Dispense Switches JDF-2S, JDF-4SSERVICE CONT Cold Water Dispense Switch JDF-4S only Location SERVICE CONT Dispense Membrane Switch all ModelsFIG.47 MEMBRANE SWITCHES FIG. 48 MEMBRANE SWITCHSERVICE CONT Cold Water Dispense Membrane Switch all ModelsSERVICE CONT EMI Filter all Models FIG. 49 EMI FILTERJDF-4S shown SERVICE CONT Lamps, Holders and Ballasts Early Models FIG. 51 LAMPS & HOLDERSFIG. 52 LAMP HOLDERS SERVICE CONT LED Lamps JDF-2S, JDF-4S Rectifier JDF-2S, JDF-4S SERVICE CONTFIG. 55 RECTIFIER Relay all Models SERVICE CONTFIG. 57 RELAY Resistor all 230V Models SERVICE CONTFIG. 59 RESISTOR FIG. 62 COLD WATER SOLENOID SERVICE CONT Solenoid - Cold Water JDF-4S onlyWHI/VIO to Control Board WHI to Control BoardBRN to Control Board SERVICE CONT Solenoid - Inlet all ModelsVOLTAGE SERVICE CONT Temperature Probe all ModelsTEMP RESISTANCERESISTANCE SERVICE CONT Temperature Sensor all ModelsFIG. 67 TEMPERATURE SENSOR TEMPto Control SERVICE CONT Transformer all ModelsWHI/BLU to Control Board J6-1,J12-1WHI - 120V T2, 240V T6 SERVICE CONT Transformer - Lited Doors JDF-2S, JDF-4SWHI/GRN - T8 WHI/BLK - T12Station Triac MapStation Station2 WIRE DIAGRAM for JDF-2S LED Lited DoorsSCHEMATIC WIRING DIAGRAM JDF-2S ELECTRICAL SCHEMATIC Models withDIAGRAM JDF-2S ELECTRICAL SCHEMATIC DIAGRAM for JDF-2SModels with Flourescent Lited Doors SCHEMATIC WIRINGSINGLE PHASE ELECTRICAL SCHEMATIC DIAGRAM for JDF-4S Models with LED Lited DoorsSCHEMATIC WIRING DIAGRAM JDF-4S 2 WIREModels with Flourescent Lited Doors ELECTRICAL SCHEMATIC DIAGRAM for JDF-4SSCHEMATIC WIRING DIAGRAM JDF 2 WIRE SINGLE PHASE2 WIRE ELECTRICAL SCHEMATIC DIAGRAM for JDF-4DPress & Release Models SCHEMATIC WIRING DIAGRAM JDF-4DSINGLE PHASE ELECTRICAL SCHEMATIC DIAGRAM for JDF-4D Portion Control ModelsSCHEMATIC WIRING DIAGRAM JDF-4D 2 WIRESINGLE PHASE ELECTRICAL SCHEMATIC DIAGRAM for JDF-4S-SBSCHEMATIC WIRING DIAGRAM JDF-4S-SB 2 WIRE