Manuals / Bush Hog / Lawn and Garden / Compact Loader

Bush Hog 5045 manual Bush Hog L.L.C Walvoil Valve Mounting Instructions, Installation Notes

Models: 5045

1 56

Download 56 pages 60.88 Kb

Page 34

BUSH HOG L.L.C.

BUSH HOG L.L.C.

WALVOIL VALVE MOUNTING INSTRUCTIONS

50051735 & 50051736 SINGLE HANDLE VALVE KITS

HYDRAULIC ATTACHMENT

FOR 3545, 4045, 5045, 6045 LOADERS

(See Page 2 for Valve Mounting Instructions)

WARNING

THE LOADER CAN FALL FROM HYDRAULIC

SYSTEM FAILURE. TO AVOID SERIOUS

INJURY OR DEATH, SECURELY SUPPORT

LOADER BEFORE WORKING UNDERNEATH.

CAUTION

USE A PIECE OF CARDBOARD OR WOOD RATHER

THAN HANDS AND WEAR EYE PROTECTION WHEN

SEARCHING FOR HYDRAULIC LEAKS. ESCAPING

HYDRAULIC OIL UNDER PRESSURE CAN PENETRATE

SKIN. IF OIL IS INJECTED INTO SKIN, IT MUST BE

SURGICALLY REMOVED WITHIN A FEW HOURS BY A

DOCTOR OR GANGRENE MAY RESULT.

INSTALLATION NOTES

zCAUTION: Before leaving tractor seat, stop engine, lock brake, relieve hydraulic pressure, and remove key. Do Not allow bystanders in work area.

zWhen attaching a loader Valve to the rear remotes of the tractor, a power beyond kit is not required. A power beyond kit Must be used when attaching a loader valve to a hydraulic source other than to the rear remotes of a tractor having an Open center hydraulic system.

zA power beyond kit is Not required on tractors with a Closed center hydraulic system. The loader valve may be attached to the tractor at the rear remotes or, at another hydraulic source recommended by the tractor manufacturer.

Page 1 04/12/06 62-06

Instruction Sheet No. 50051652

Image 34

Bush Hog Bush Hog L.L.C Walvoil Valve Mounting Instructions, FOR 3545, 4045, 5045, 6045 LOADERS, Installation Notes

Contents

BUSH HOG FrontEndLoaders 3545 / 4045 / 5045 / 6045 Operator’s ManualASSEMBLY OPERATION MAINTENANCE $4.00CONGRATULATIONS 3545 TABLE OF CONTENTSRETAIL CUSTOMER’S RESPONSIBILITY UNDER THE BUSH HOG WARRANTY SECTION/PARATHIS LIMITED WARRANTY SHALL NOT APPLY LIMITED WARRANTYDISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES USE ROPS ROLLOVER PROTECTIVE STRUCTURE AND 3545DEALER PREPARATION CHECK LIST SEAT BELT EQUIPPED TRACTORS FOR OPERATOR USE IN ALL LOADER OPERATIONSSafety Signs Signal Words Safety Alert SymbolYOUR SAFETY IS INVOLVED!” THE TRACTOR IMPORTANT SAFETY PRECAUTIONSTHE LOADER SAFETY PRECAUTIONS CONTINUED OPERATING THE LOADERIMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONSEMPLOYEE TRACTOR OPERATING INSTRUCTIONS 1-1 INTRODUCTION SECTION INTRODUCTION AND DESCRIPTIONBucket Cylinder Cross Tube Bucket 1-2 DESCRIPTIONTable 1-1 TECHNICAL SPECIFICATIONS 2-1 PREPARING TRACTOR SECTION LOADER MOUNTING AND DISMOUNTING2-2 MOUNTING LOADER C. Check that lift cylinders are fully retracted 2-3 DISMOUNTING LOADER 3-2 PRE-OPERATION SECTION OPERATING INSTRUCTIONS3-1 GENERAL SAFETY 3-3 INITIAL LOADER OPERATION3-8 FLOAT POSITION 3-4 EXTERNAL LOADER AND/OR TRAC- TOR VALVE3-7 NEUTRAL POSITION 3-9 REGENERATIVE VALVE POSITION3-12 REMOVING AIR FROM HYDRAULIC SYSTEM 3-14 BUCKET LEVEL INDICATOR ROD3-13 HOSE IDENTIFICATION FILLING THE BUCKET Approach and enter the pile with a level bucket CARRYING THE LOAD FLOAT SURFACE MATERIAL LOADING FROM A BANK OPERATING WITH FLOAT CONTROLFLOAT Sidecutting is a good technique for cutting down a big pilePEELING AND SCRAPING 6” Possibility of rolling the tractor over 3-15 BALE SPEAR OPERATIONHandling large heavy objects can be extremely dangerous due to Possibility of upending the tractor3-16 FORK LIFT OPERATION 3-17 TRANSPORTING3-18 SKID STEER QUICK HITCH OPERATION 4-1 MAINTENANCE CHECK LIST SECTION MAINTENANCE4-2 LUBRICATION Figure 4-4 TROUBLESHOOTING 4-3 HYDRAULIC SYSTEM PRESSURE REQUIREMENTSsetting recommended TABLE 4-1 TROUBLESHOOTING PROCEDURESPROBLEM POSSIBLE CAUSESECTION V ASSEMBLY 5-1 TRACTOR PREPARATION5-2 TRACTOR BALLAST 5-3 INSTALLATION5-5 BUCKET LEVEL INDICATOR ROD 5-4 HYDRAULIC HOOKUP5-6 FORK LIFT OPTION 5-7 BALE SPEAR OPTIONTINE TEETH 5-8 OPTIONAL BUCKET ITEMS ASSEMBLY SPILL GUARD ATTACHMENTDIGGING TEETH SIDE CUTTING EDGESMETRIC TORQUE SPECIFICATIONSAMERICAN Bolt Head MarkingsSAFETY DECALS DECALS50051735 & 50051736 SINGLE HANDLE VALVE KITS HYDRAULIC ATTACHMENT INSTALLATION NOTESBUSH HOG L.L.C WALVOIL VALVE MOUNTING INSTRUCTIONS FOR 3545, 4045, 5045, 6045 LOADERSInlet VALVE PLUMBING ASSEMBLYWALVOIL VALVE MOUNTING INSTRUCTIONS See Page 3 for Valve Stand Mounting InstructionsHoses Not Shown for Clarity VALVE STAND ASSEMBLY INSTRUCTIONSVALVE SHORT MOUNT ASSEMBLY INSTRUCTIONS Hoses Not Shown for Clarity50027307 BAG OF FASTENERS 50051735 SINGLE HANDLE VALVE KIT50051736 SINGLE HANDLE VALVE KIT P.O. Box 1039 Selma, AL50051730 CABLE CONTROL VALVE KIT HYDRAULIC ATTACHMENT ATTACHING HANDLE MOUNT, CONTROL HANDLE AND CABLES TO TRACTORBUSH HOG L.L.C MOUNTING INSTRUCTIONS 50051729 CABLE CONTROL VALVE KIT FOR MID MOUNT LOADERS25H41276 FRONT OF TRACTOR Disconnect Fittings Not 10. ATTACHING VALVE TO LOADER FRAMEHoses and Quick Shown for Clarity15. CONNECTING HYDRAULICS Refer to Fig. 5 and Fig Attach as follows Refer to Fig19. Adjust the cables so the control handle operates as follows 50027390 BAG OF HARDWARE 50051730 CABLE CONTROL VALVE KIT50051729 CABLE CONTROL VALVE KIT PART NUMBERHOSE AND COUPLER ASSEMBLY INSTALLATION INSTRUCTIONS FOR 24H46343 POWER BEYOND KITDISCONNECTING LOADER VALVE FROM TRACTOR Here CABLE CONTROL WALVOIL VALVE ASSEMBLYInlet WALVOIL CABLE CONTROL VALVEInlet STANDARD WALVOIL VALVE ASSEMBLYInlet STANDARD WALVOIL VALVESept Instruction Sheet No. 25H46344 50051690 SELF LEVELING VALVE BUNDLE MOUNTING INSTRUCTIONS ~ ASSEMBLY INSTRUCTIONS ~BUSH HOG 3545, 4045, 5045 & 6045 MID MOUNT FRONT END LOADERS F E D A C B R.H. Lift Cylinder FRONTL.H. Lift Cylinder Raising Adjustment ADJUSTMENTLowering Adjustment DESCRIPTIONBUSH HOG MOUNTING INSTRUCTIONS FOR 24H49871 GRAPPLE ATTACHMENTInstruction Sheet 25H49884 BUSH HOGPage 5/8” LockwashersHydraulic Cylinder 24H49871 GRAPPLE ATTACHMENTPART NAME 24H49885 BAG OF HARDWARE