Manuals / Bush Hog / Lawn and Garden / Compact Loader

Bush Hog 5045 Cable Control Walvoil Valve Assembly, Inlet, Here, Walvoil Cable Control Valve

Models: 5045

1 56

Download 56 pages 60.88 Kb

Page 46

WALVOIL CABLE CONTROL VALVE

WALVOIL CABLE CONTROL VALVE

WARNING

When loader hydraulics are disconnected from tractor hydraulics, hoses A & B must be con- nected to complete tractor hydraulic circuit.

FAILURE TO DO THIS WILL CAUSE SERIOUS DAMAGE TO TRACTOR HYDRAULICS SYSTEM.

Inlet Valve Plug

Power

Beyond Plug

Straight

Adapter

90° Elbow

Pressure			Inlet
Pressure						Here)
To					Hose
				Long	Hose
		(Use		Long				Inlet
	Inlet	(Use					Return	Inlet
Sump	Inlet
				Pressurized

To
To
			To

		A
	These hoses	C
	to be furnished	C
	to be furnished
	by dealer.	B
		B

CABLE CONTROL WALVOIL VALVE ASSEMBLY

1.Remove valve plug from right side of valve.

2.Install power beyond plug in same hole, valve plug removed. (Note: Power beyond plug is shipped with valve.) Torque from 20 to 25 ft./lbs.

3.Install straight adaptor 3/4” JIC to 7/8” SAE in power beyond port.

4.Before further hydraulic assembly is done, install valve to valve mounting hardware as instructed in the hose and valve kit package. The straight adaptor should extend through the hole in the right side of the valve mount.

5.Install 90° elbow 3/4” JIC male to 3/4” JIC female on straight adaptor installed in power beyond plug.

Sept. -05

Instruction Sheet No. 25H46344

Image 46

Bush Hog 5045 Cable Control Walvoil Valve Assembly, Inlet, Here, Walvoil Cable Control Valve, These hoses, to be furnished

Contents

BUSH HOG FrontEndLoaders 3545 / 4045 / 5045 / 6045 Operator’s ManualASSEMBLY OPERATION MAINTENANCE $4.00CONGRATULATIONS 3545 TABLE OF CONTENTSRETAIL CUSTOMER’S RESPONSIBILITY UNDER THE BUSH HOG WARRANTY SECTION/PARATHIS LIMITED WARRANTY SHALL NOT APPLY LIMITED WARRANTYDISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES USE ROPS ROLLOVER PROTECTIVE STRUCTURE AND 3545DEALER PREPARATION CHECK LIST SEAT BELT EQUIPPED TRACTORS FOR OPERATOR USE IN ALL LOADER OPERATIONSSafety Signs Signal Words Safety Alert SymbolYOUR SAFETY IS INVOLVED!” THE TRACTOR IMPORTANT SAFETY PRECAUTIONSTHE LOADER SAFETY PRECAUTIONS CONTINUED OPERATING THE LOADERIMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONSEMPLOYEE TRACTOR OPERATING INSTRUCTIONS 1-1 INTRODUCTION SECTION INTRODUCTION AND DESCRIPTIONBucket Cylinder Cross Tube Bucket 1-2 DESCRIPTIONTable 1-1 TECHNICAL SPECIFICATIONS 2-1 PREPARING TRACTOR SECTION LOADER MOUNTING AND DISMOUNTING2-2 MOUNTING LOADER C. Check that lift cylinders are fully retracted 2-3 DISMOUNTING LOADER 3-2 PRE-OPERATION SECTION OPERATING INSTRUCTIONS3-1 GENERAL SAFETY 3-3 INITIAL LOADER OPERATION3-8 FLOAT POSITION 3-4 EXTERNAL LOADER AND/OR TRAC- TOR VALVE3-7 NEUTRAL POSITION 3-9 REGENERATIVE VALVE POSITION3-12 REMOVING AIR FROM HYDRAULIC SYSTEM 3-14 BUCKET LEVEL INDICATOR ROD3-13 HOSE IDENTIFICATION FILLING THE BUCKET Approach and enter the pile with a level bucket CARRYING THE LOAD FLOAT SURFACE MATERIAL LOADING FROM A BANK OPERATING WITH FLOAT CONTROLFLOAT Sidecutting is a good technique for cutting down a big pilePEELING AND SCRAPING 6” Possibility of rolling the tractor over 3-15 BALE SPEAR OPERATIONHandling large heavy objects can be extremely dangerous due to Possibility of upending the tractor3-16 FORK LIFT OPERATION 3-17 TRANSPORTING3-18 SKID STEER QUICK HITCH OPERATION 4-1 MAINTENANCE CHECK LIST SECTION MAINTENANCE4-2 LUBRICATION Figure 4-4 TROUBLESHOOTING 4-3 HYDRAULIC SYSTEM PRESSURE REQUIREMENTSsetting recommended TABLE 4-1 TROUBLESHOOTING PROCEDURESPROBLEM POSSIBLE CAUSESECTION V ASSEMBLY 5-1 TRACTOR PREPARATION5-2 TRACTOR BALLAST 5-3 INSTALLATION5-5 BUCKET LEVEL INDICATOR ROD 5-4 HYDRAULIC HOOKUP5-6 FORK LIFT OPTION 5-7 BALE SPEAR OPTIONTINE TEETH 5-8 OPTIONAL BUCKET ITEMS ASSEMBLY SPILL GUARD ATTACHMENTDIGGING TEETH SIDE CUTTING EDGESMETRIC TORQUE SPECIFICATIONSAMERICAN Bolt Head MarkingsSAFETY DECALS DECALS50051735 & 50051736 SINGLE HANDLE VALVE KITS HYDRAULIC ATTACHMENT INSTALLATION NOTESBUSH HOG L.L.C WALVOIL VALVE MOUNTING INSTRUCTIONS FOR 3545, 4045, 5045, 6045 LOADERSInlet VALVE PLUMBING ASSEMBLYWALVOIL VALVE MOUNTING INSTRUCTIONS See Page 3 for Valve Stand Mounting InstructionsHoses Not Shown for Clarity VALVE STAND ASSEMBLY INSTRUCTIONSVALVE SHORT MOUNT ASSEMBLY INSTRUCTIONS Hoses Not Shown for Clarity50027307 BAG OF FASTENERS 50051735 SINGLE HANDLE VALVE KIT50051736 SINGLE HANDLE VALVE KIT P.O. Box 1039 Selma, AL50051730 CABLE CONTROL VALVE KIT HYDRAULIC ATTACHMENT ATTACHING HANDLE MOUNT, CONTROL HANDLE AND CABLES TO TRACTORBUSH HOG L.L.C MOUNTING INSTRUCTIONS 50051729 CABLE CONTROL VALVE KIT FOR MID MOUNT LOADERS25H41276 FRONT OF TRACTOR Disconnect Fittings Not 10. ATTACHING VALVE TO LOADER FRAMEHoses and Quick Shown for Clarity15. CONNECTING HYDRAULICS Refer to Fig. 5 and Fig Attach as follows Refer to Fig19. Adjust the cables so the control handle operates as follows 50027390 BAG OF HARDWARE 50051730 CABLE CONTROL VALVE KIT50051729 CABLE CONTROL VALVE KIT PART NUMBERHOSE AND COUPLER ASSEMBLY INSTALLATION INSTRUCTIONS FOR 24H46343 POWER BEYOND KITDISCONNECTING LOADER VALVE FROM TRACTOR Here CABLE CONTROL WALVOIL VALVE ASSEMBLYInlet WALVOIL CABLE CONTROL VALVEInlet STANDARD WALVOIL VALVE ASSEMBLYInlet STANDARD WALVOIL VALVESept Instruction Sheet No. 25H46344 50051690 SELF LEVELING VALVE BUNDLE MOUNTING INSTRUCTIONS ~ ASSEMBLY INSTRUCTIONS ~BUSH HOG 3545, 4045, 5045 & 6045 MID MOUNT FRONT END LOADERS F E D A C B R.H. Lift Cylinder FRONTL.H. Lift Cylinder Raising Adjustment ADJUSTMENTLowering Adjustment DESCRIPTIONBUSH HOG MOUNTING INSTRUCTIONS FOR 24H49871 GRAPPLE ATTACHMENTInstruction Sheet 25H49884 BUSH HOGPage 5/8” LockwashersHydraulic Cylinder 24H49871 GRAPPLE ATTACHMENTPART NAME 24H49885 BAG OF HARDWARE