Manuals / Bush Hog / Lawn and Garden / Lawn Mower

Bush Hog manual Model HM2007 - 13mm 1/2”, Model HM2008 - 11mm 7/16”, Model HM2009 - 8 mm 5/16”

Models: HM2009 HM2007 HM2008

1 62

Download 62 pages 14.31 Kb

Page 26

Image 26

450 - 480 mm (Model HM2009 - max. 450 mm/18”)

(18” - 19”)

Model HM2007 - 13mm (1/2”)

Model HM2008 - 11mm (7/16”)

*Model HM2009 - 8 mm (5/16”)

min. 950 mm (38”)

Page 26

Image 26

Bush Hog manual Model HM2007 - 13mm 1/2”, Model HM2008 - 11mm 7/16”, Model HM2009 - 8 mm 5/16”, min. 950 mm 38”

Contents

BUSH HOG Models HM2007, HM2008, & HM2009ASSEMBLY OPERATION MAINTENANCE Operator’s ManualCONGRATULATIONS HAY MOWER TABLE OF CONTENTSRETAIL CUSTOMER’S RESPONSIBILITY UNDER THE BUSH HOG WARRANTY SECTIONBUSH HOG LIMITED WARRANTYTHIS LIMITED WARRANTY SHALL NOT APPLY DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGESDEALER PREPARATION CHECK LIST HAY MOWERYOUR SAFETY IS INVOLVED!” Safety Alert SymbolSafety Signs Signal Words IMPORTANT SAFETY PRECAUTIONS EMPLOYEE TRACTOR OPERATING INSTRUCTIONS EMPLOYERS, EMPLOYEES AND OPERATIONSIMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING This Act SeeksModels HM2007 - HM2008 - HM2009 All measurements are approximate and stated in mm and inchesModel HM2008 Fitting to the tractorModel HM2007 Model HM2009Machine Identification kg / lb General Safety Instructions Safety① ② ③ ④ ⑤ ⑥ ⑦ Page ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ HM2007 ModelKg lb HM2008Safety instructions during crane lift Page New Machine - be careful ① ② ③ ④ ⑤ ⑥ ⑦11-1/2” HM2009HM2007, HM2008 290 mmModel Preparation For UseDo the following before coupling the machine to the tractor ColorRemove Clip Pin and Rotate Pawl Clip PinPawl Fitting of the suspension Mounting - coupling① ② ③ min. 150 mm 6” b c d1/2” Shortening of the shaft ① - ② ③ - ④PTO shaft Checking of PTO shaft lengthModel HM2009 - 8 mm 5/16” Model HM2007 - 13mm 1/2”Model HM2008 - 11mm 7/16” min. 950 mm 38”Stabilizer ① ② ③Height of the suspension Lifting heightSupport Legs 1 Transport PositionUn-Hitched F Chain④ - ➆ Transport - Unhitching① - ② Transport60 ft./lbs 80 ±95 ± 70 ft./lbsOperate with safety - note the following Maintenance① - ④ Knives - cutting discsE Hole In Front Belt Guard Lubrication generally ① - ②V-belts Lubrication Lubricants, - see pagemax. 9 mm 11/32” Oil Filler Plugmin. 6 mm 1/4” Oil - bevel gearbox ① - ④Oil - cutterbar Oil levelSwath Roller Swath BoardRight-hand & Left-hand swath boards Optional equipmentRight-hand & Left-hand swath rollers 5/16 - 1/8” 1 Hillside Kit As Seen From Below2-3 mm 3 Inside High SkidOptional high skid ① - ② ③ - ④Optional hillside kit Flat Blades Throwing WingsLeft Cone Throwing wings ① ② ③Special flat knives Left cone19-5/8” 1.4 - 2.8 mm055 - .110” 500 mm① - ② Directions for repairImportant, when fitting the gear to the machine NOTE THE FOLLOWINGPage Collar bearings illustration ① - ➃Intermediate gear illustration Fixing of collar bearing ilustrationPossible Cause Problem/Fault Analysis and CorrectionsProblem CorrectionWinter storage Torque Value Conversion ChartLubricants SupplierASSEMBLY INSTRUCTIONS Models HM2007, HM2008 & HM200916-35 mm ASSEMBLY16-40 mm “T” Support Leg “U” Bracket12 -30 mm Also Bottom Front - Not Seen 10 x 25 mm 12 - 40 mm 12 - 40 mm Plow Bolt 12 - 35mm Plow Bolt12-40 mm Twisted StrutAttach Hydraulic Hose With Clamp 59 ft./lbs Green - NOTE Only used with flat blade kitModel CUTTING DISCS ARRANGEMENTBlade Rotation HM200910 - 30mm 10 - 35 mm10 - 30 mm Figure 11 Curtain Frame10 -30 mm 30 -10.5 - 3 mm 10 - 30 mm 30 -10.5 - 3 mm10 - 40 mm 18. Attach front edge rail to frame. Figure6 - 20 mm 10 -30 mm 30 - 10.5 - 3 mm12 -40 mm 12 - 40 mmOPTIONAL EQUIPMENT 12 - 35mmSAFETY DECALS 50030642Page Page P.O. Box 1039 Selma, AL Telephone 334 BUSH HOGL.L.C