Manuals / Bush Hog / Lawn and Garden / Lawn Mower

Bush Hog HM2007, HM2008, HM2009 manual Optional equipment, Right-hand & Left-hand swath rollers

Models: HM2009 HM2007 HM2008

1 62

Download 62 pages 14.31 Kb

Page 37

Image 37

①

②

Optional equipment

Right-hand & Left-hand swath rollers

The machine can be equipped with swath rollers as shown.

Right-hand & Left-hand swath boards

The machine can be equipped with swath boards as shown.

Page 37

Image 37

Bush Hog HM2007, HM2008 manual Optional equipment, Right-hand & Left-hand swath rollers, Right-hand & Left-hand swath boards

Contents

ASSEMBLY OPERATION MAINTENANCE Models HM2007, HM2008, & HM2009BUSH HOG Operator’s ManualCONGRATULATIONS RETAIL CUSTOMER’S RESPONSIBILITY UNDER THE BUSH HOG WARRANTY TABLE OF CONTENTSHAY MOWER SECTIONTHIS LIMITED WARRANTY SHALL NOT APPLY LIMITED WARRANTYBUSH HOG DISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGESHAY MOWER DEALER PREPARATION CHECK LISTSafety Signs Signal Words Safety Alert SymbolYOUR SAFETY IS INVOLVED!” IMPORTANT SAFETY PRECAUTIONS IMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYERS, EMPLOYEES AND OPERATIONSEMPLOYEE TRACTOR OPERATING INSTRUCTIONS This Act SeeksAll measurements are approximate and stated in mm and inches Models HM2007 - HM2008 - HM2009Model HM2007 Fitting to the tractorModel HM2008 Model HM2009Machine Identification kg / lb ① ② ③ ④ ⑤ ⑥ ⑦ SafetyGeneral Safety Instructions Page ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ Kg lb ModelHM2007 HM2008Safety instructions during crane lift Page ① ② ③ ④ ⑤ ⑥ ⑦ New Machine - be carefulHM2007, HM2008 HM200911-1/2” 290 mmDo the following before coupling the machine to the tractor Preparation For UseModel ColorPawl Clip PinRemove Clip Pin and Rotate Pawl ① ② ③ Mounting - couplingFitting of the suspension 1/2” b c dmin. 150 mm 6” PTO shaft ① - ② ③ - ④Shortening of the shaft Checking of PTO shaft lengthModel HM2008 - 11mm 7/16” Model HM2007 - 13mm 1/2”Model HM2009 - 8 mm 5/16” min. 950 mm 38”Height of the suspension ① ② ③Stabilizer Lifting heightUn-Hitched 1 Transport PositionSupport Legs F Chain① - ② Transport - Unhitching④ - ➆ Transport95 ± 80 ±60 ft./lbs 70 ft./lbs① - ④ MaintenanceOperate with safety - note the following Knives - cutting discsE Hole In Front Belt Guard V-belts ① - ②Lubrication generally Lubrication Lubricants, - see pagemin. 6 mm 1/4” Oil Filler Plugmax. 9 mm 11/32” Oil - cutterbar ① - ④Oil - bevel gearbox Oil levelSwath Board Swath RollerRight-hand & Left-hand swath rollers Optional equipmentRight-hand & Left-hand swath boards 2-3 mm 1 Hillside Kit As Seen From Below5/16 - 1/8” 3 Inside High SkidOptional hillside kit ① - ② ③ - ④Optional high skid Left Cone Throwing WingsFlat Blades Special flat knives ① ② ③Throwing wings Left cone055 - .110” 1.4 - 2.8 mm19-5/8” 500 mmImportant, when fitting the gear to the machine Directions for repair① - ② NOTE THE FOLLOWINGPage Intermediate gear illustration ① - ➃Collar bearings illustration Fixing of collar bearing ilustrationProblem Problem/Fault Analysis and CorrectionsPossible Cause CorrectionWinter storage Lubricants Conversion ChartTorque Value SupplierModels HM2007, HM2008 & HM2009 ASSEMBLY INSTRUCTIONS16-40 mm ASSEMBLY16-35 mm “T” Support Leg “U” Bracket12-40 mm 12 - 40 mm Plow Bolt 12 - 35mm Plow Bolt12 -30 mm Also Bottom Front - Not Seen 10 x 25 mm 12 - 40 mm Twisted StrutAttach Hydraulic Hose With Clamp Green - NOTE Only used with flat blade kit 59 ft./lbsBlade Rotation CUTTING DISCS ARRANGEMENTModel HM200910 - 30 mm 10 - 35 mm10 - 30mm Figure 11 Curtain Frame10 - 40 mm 10 - 30 mm 30 -10.5 - 3 mm10 -30 mm 30 -10.5 - 3 mm 18. Attach front edge rail to frame. Figure12 -40 mm 10 -30 mm 30 - 10.5 - 3 mm6 - 20 mm 12 - 40 mm12 - 35mm OPTIONAL EQUIPMENT50030642 SAFETY DECALSPage Page L.L.C BUSH HOGP.O. Box 1039 Selma, AL Telephone 334