Manuals / Bush Hog / Lawn and Garden / Lawn Mower

Bush Hog HM2009, HM2008, HM2007 manual Safety Decals, 50030642

Models: HM2009 HM2007 HM2008

1 62

Page 59

SAFETY DECALS

To promote safe operation, Bush Hog supplies safety decals on all products manufactured. Because damage can occur to safety decals either through shipment, use or reconditioning, Bush Hog will, upon request, provide safety decals for any of our products in the field at no charge. Contact your authorized Bush Hog dealer for more information.

50030642

Page 59

Image 59

Bush Hog HM2009, HM2008, HM2007 manual Safety Decals, 50030642

Contents

Operator’s Manual Models HM2007, HM2008, & HM2009ASSEMBLY OPERATION MAINTENANCE BUSH HOGCONGRATULATIONS SECTION TABLE OF CONTENTSRETAIL CUSTOMER’S RESPONSIBILITY UNDER THE BUSH HOG WARRANTY HAY MOWERDISCLAIMER OF IMPLIED WARRANTIES & CONSEQUENTIAL DAMAGES LIMITED WARRANTYTHIS LIMITED WARRANTY SHALL NOT APPLY BUSH HOGHAY MOWER DEALER PREPARATION CHECK LISTYOUR SAFETY IS INVOLVED!” Safety Alert SymbolSafety Signs Signal Words IMPORTANT SAFETY PRECAUTIONS This Act Seeks EMPLOYERS, EMPLOYEES AND OPERATIONSIMPORTANT FEDERAL LAWS AND REGULATIONS* CONCERNING EMPLOYEE TRACTOR OPERATING INSTRUCTIONSAll measurements are approximate and stated in mm and inches Models HM2007 - HM2008 - HM2009Model HM2009 Fitting to the tractorModel HM2007 Model HM2008Machine Identification kg / lb General Safety Instructions Safety① ② ③ ④ ⑤ ⑥ ⑦ Page ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ HM2008 ModelKg lb HM2007Safety instructions during crane lift Page ① ② ③ ④ ⑤ ⑥ ⑦ New Machine - be careful290 mm HM2009HM2007, HM2008 11-1/2”Color Preparation For UseDo the following before coupling the machine to the tractor ModelRemove Clip Pin and Rotate Pawl Clip PinPawl Fitting of the suspension Mounting - coupling① ② ③ min. 150 mm 6” b c d1/2” Checking of PTO shaft length ① - ② ③ - ④PTO shaft Shortening of the shaftmin. 950 mm 38” Model HM2007 - 13mm 1/2”Model HM2008 - 11mm 7/16” Model HM2009 - 8 mm 5/16”Lifting height ① ② ③Height of the suspension StabilizerF Chain 1 Transport PositionUn-Hitched Support LegsTransport Transport - Unhitching① - ② ④ - ➆70 ft./lbs 80 ±95 ± 60 ft./lbsKnives - cutting discs Maintenance① - ④ Operate with safety - note the followingE Hole In Front Belt Guard Lubrication Lubricants, - see page ① - ②V-belts Lubrication generallymax. 9 mm 11/32” Oil Filler Plugmin. 6 mm 1/4” Oil level ① - ④Oil - cutterbar Oil - bevel gearboxSwath Board Swath RollerRight-hand & Left-hand swath boards Optional equipmentRight-hand & Left-hand swath rollers 3 Inside High Skid 1 Hillside Kit As Seen From Below2-3 mm 5/16 - 1/8”Optional high skid ① - ② ③ - ④Optional hillside kit Flat Blades Throwing WingsLeft Cone Left cone ① ② ③Special flat knives Throwing wings500 mm 1.4 - 2.8 mm055 - .110” 19-5/8”NOTE THE FOLLOWING Directions for repairImportant, when fitting the gear to the machine ① - ②Page Fixing of collar bearing ilustration ① - ➃Intermediate gear illustration Collar bearings illustrationCorrection Problem/Fault Analysis and CorrectionsProblem Possible CauseWinter storage Supplier Conversion ChartLubricants Torque ValueModels HM2007, HM2008 & HM2009 ASSEMBLY INSTRUCTIONS“T” Support Leg “U” Bracket ASSEMBLY16-40 mm 16-35 mmTwisted Strut 12 - 40 mm Plow Bolt 12 - 35mm Plow Bolt12-40 mm 12 -30 mm Also Bottom Front - Not Seen 10 x 25 mm 12 - 40 mmAttach Hydraulic Hose With Clamp Green - NOTE Only used with flat blade kit 59 ft./lbsHM2009 CUTTING DISCS ARRANGEMENTBlade Rotation ModelFigure 11 Curtain Frame 10 - 35 mm10 - 30 mm 10 - 30mm18. Attach front edge rail to frame. Figure 10 - 30 mm 30 -10.5 - 3 mm10 - 40 mm 10 -30 mm 30 -10.5 - 3 mm12 - 40 mm 10 -30 mm 30 - 10.5 - 3 mm12 -40 mm 6 - 20 mm12 - 35mm OPTIONAL EQUIPMENT50030642 SAFETY DECALSPage Page P.O. Box 1039 Selma, AL Telephone 334 BUSH HOGL.L.C