Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 3H08-04, 3H02-04 manual Appendix A Technical Specifications

Models: 3H08-04 3H02-04

1 42

Download 42 pages 24.72 Kb

Page 35

APPENDIX A

TECHNICAL SPECIFICATIONS

Standards Compliance

•Ethernet Version 2

•IEEE 802.3, 802.3u, 802.2, 802.1(d), 100BASE-TX, 100BASE-FX

Protocol Translations

•TCP/IP

•IPX

•AppleTalk Phase II

Dimensions

Length	12.2 in. (30.99 cm)
Width	9.5 in. (24.13 cm)
Weight	approximately 1.375 lb. (.62 kg)
Environmental Requirements
Operating temperature	5˚ C to 40˚ C (41˚ F to 104˚ F)
Storage temperature	-30˚ C to 90˚ C (-22˚ F to 194˚ F)
Relative humidity	0% to 95% non-condensing

FE Switch Module User Guide

Page A-1

Image 35

Cabletron Systems 3H08-04, 3H02-04 manual Appendix A Technical Specifications

Contents

FAST ETHERNET SWITCH MODULE 3H02-04 AND 3H08-04 USER GUIDE Page FE Switch Module User Guide VCCI NOTICE FE Switch Module User GuideFCC NOTICE DOC NOTICECABLETRON SOFTWARE PROGRAM LICENSE EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITYFE Switch Module User Guide CABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENTUNITED STATES GOVERNMENT RESTRICTED RIGHTS FE Switch Module User GuideCHAPTER 5 DIAGNOSTICS AND TROUBLESHOOTING CONTENTSCHAPTER 2 CONNECTING TO THE NETWORK CONFIGURINGCHAPTER 6 ADDING/SWAPPING MODULES ContentsTECHNICAL SPECIFICATIONS FE Switch Module User GuideCHAPTER INTRODUCTION Chapter 1 Introduction 1.1 USING THIS MANUAL1.2 OVERVIEW 1.3 3H02-04 FE SWITCH MODULE1.3.3 Ofﬂine Button 1.3.1 Connectors1.3.2 LEDs 1.4.3 Ofﬂine Button 1.4 3H08-04 FE SWITCH MODULE1.4.1 Connectors 1.4.2 LEDsChapter 1 Introduction 1.5 DOCUMENT CONVENTIONSFE Switch Module User Guide The following conventions are used throughout this documentanonymous 1.6 RELATED MANUALS1.7 GETTING HELP ATX User Guide ATX MIB Reference GuideA description of the failure 2.1 POWER-UP LED SEQUENCE CHAPTER CONNECTING TO THE NETWORK2.2.1 Connecting the 3H02-04 FE Switch Module 2.2 CONNECTING TO A NETWORKFigure 2-2 3H08-04 Front Panel Connections 2.2.2 Connecting the 3H08-04 FE Switch ModulePage Chapter 2 Connecting to the NetworkFE Switch Module User Guide CHAPTER CONFIGURING 3.2 LOCAL CONSOLE MANAGER COMMANDS 3.1 CONNECTING THE LOCAL CONSOLE MANAGERCHAPTER MONITORING 4.1 DISPLAYING SWITCH MODULE PORT STATUSDisabled - The port isn’t conﬁgured for Spanning Tree Total Collisions - number of collision during packet transmissions Page FE Switch Module User GuideChapter 4 Monitoring 5.2 POWER-UP RESULTS CHAPTER DIAGNOSTICS AND TROUBLESHOOTING5.1 POWER-UP TESTS Chapter 5 Diagnostics and Troubleshooting 5.3 OPERATIONAL DIAGNOSTICS5.5 TROUBLESHOOTING 5.5.1 If the Module Fails to Power Up 5.4 DIAGNOSTIC RESULTS5.5.2 Connectivity Problems CHAPTER ADDING/SWAPPING MODULES 6.1 UNPACKING THE SWITCH MODULE6.2 ADDING A SWITCH MODULE 6.3 SWAPPING A SWITCH MODULE 7. Tighten the screws on each side of the switch module’s front panel Page FE Switch Module User GuideChapter 6 Adding/Swapping Modules APPENDIX A TECHNICAL SPECIFICATIONS 3H02-04 FE Switch Module User Guide B.1 TYPES/CONNECTORSB.2 CABLE SPECIFICATIONS APPENDIX B CABLESFigure B-1 RJ45 Connector Pin Numbers B.3 FAST ETHERNET PIN ASSIGNMENTS B.3.1 About RJ45 ConnectorsRJ45 Pin B.3.2 Crossover Wiring for the 3H02-04Table B-5 Crossover RJ45 Wiring Configuration Table B-4 RJ45 Crossover Pin AssignmentsB.3.5 Deﬁnitions B.3.3 Straight-Through Wiring for the 3H02-04B.3.4 Limitations & Restrictions INDEX Index-2 FE Switch Module User GuideIndex