Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 3H02-04 Connecting The Local Console Manager, Local Console Manager Commands

Models: 3H08-04 3H02-04

1 42

Download 42 pages 24.72 Kb

Page 22

Chapter 3: Conﬁguring

3.1 CONNECTING THE LOCAL CONSOLE MANAGER

Connect the Local Console Manager to the ATX. For speciﬁc instructions, see Chapter 2, Connecting to the Network of the ATX User Guide.

Make sure the ATX is powered on and press <Return> a few times. When the ATX> prompt is displayed, the Local Console Manager is ready to use. The default password is <Return>.

3.2 LOCAL CONSOLE MANAGER COMMANDS

To conﬁgure the switch modules, refer to the ATX User Guide for Local Console Manager commands generic to all modules, Make sure you’re familiar with Local Console Manager before conﬁguring the module. For speciﬁc instructions on displaying the port status, see Chapter 4.

Page 3-2

FE Switch Module User Guide

Image 22

Cabletron Systems 3H02-04, 3H08-04 manual Connecting The Local Console Manager, Local Console Manager Commands

Contents

FAST ETHERNET SWITCH MODULE 3H02-04 AND 3H08-04 USER GUIDE Page FE Switch Module User Guide DOC NOTICE FE Switch Module User GuideFCC NOTICE VCCI NOTICECABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT EXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITYFE Switch Module User Guide CABLETRON SOFTWARE PROGRAM LICENSEFE Switch Module User Guide UNITED STATES GOVERNMENT RESTRICTED RIGHTSCONFIGURING CONTENTSCHAPTER 2 CONNECTING TO THE NETWORK CHAPTER 5 DIAGNOSTICS AND TROUBLESHOOTINGFE Switch Module User Guide ContentsTECHNICAL SPECIFICATIONS CHAPTER 6 ADDING/SWAPPING MODULESCHAPTER INTRODUCTION 1.1 USING THIS MANUAL Chapter 1 Introduction1.3 3H02-04 FE SWITCH MODULE 1.2 OVERVIEW1.3.2 LEDs 1.3.1 Connectors1.3.3 Ofﬂine Button 1.4.2 LEDs 1.4 3H08-04 FE SWITCH MODULE1.4.1 Connectors 1.4.3 Ofﬂine ButtonThe following conventions are used throughout this document 1.5 DOCUMENT CONVENTIONSFE Switch Module User Guide Chapter 1 IntroductionATX User Guide ATX MIB Reference Guide 1.6 RELATED MANUALS1.7 GETTING HELP anonymousA description of the failure CHAPTER CONNECTING TO THE NETWORK 2.1 POWER-UP LED SEQUENCE2.2 CONNECTING TO A NETWORK 2.2.1 Connecting the 3H02-04 FE Switch Module2.2.2 Connecting the 3H08-04 FE Switch Module Figure 2-2 3H08-04 Front Panel ConnectionsFE Switch Module User Guide Chapter 2 Connecting to the NetworkPage CHAPTER CONFIGURING 3.1 CONNECTING THE LOCAL CONSOLE MANAGER 3.2 LOCAL CONSOLE MANAGER COMMANDS4.1 DISPLAYING SWITCH MODULE PORT STATUS CHAPTER MONITORINGDisabled - The port isn’t conﬁgured for Spanning Tree Total Collisions - number of collision during packet transmissions Chapter 4 Monitoring FE Switch Module User GuidePage 5.1 POWER-UP TESTS CHAPTER DIAGNOSTICS AND TROUBLESHOOTING5.2 POWER-UP RESULTS 5.3 OPERATIONAL DIAGNOSTICS Chapter 5 Diagnostics and Troubleshooting5.4 DIAGNOSTIC RESULTS 5.5 TROUBLESHOOTING 5.5.1 If the Module Fails to Power Up5.5.2 Connectivity Problems 6.2 ADDING A SWITCH MODULE 6.1 UNPACKING THE SWITCH MODULECHAPTER ADDING/SWAPPING MODULES 6.3 SWAPPING A SWITCH MODULE 7. Tighten the screws on each side of the switch module’s front panel Chapter 6 Adding/Swapping Modules FE Switch Module User GuidePage APPENDIX A TECHNICAL SPECIFICATIONS 3H02-04 APPENDIX B CABLES B.1 TYPES/CONNECTORSB.2 CABLE SPECIFICATIONS FE Switch Module User GuideB.3 FAST ETHERNET PIN ASSIGNMENTS B.3.1 About RJ45 Connectors Figure B-1 RJ45 Connector Pin NumbersTable B-4 RJ45 Crossover Pin Assignments B.3.2 Crossover Wiring for the 3H02-04Table B-5 Crossover RJ45 Wiring Configuration RJ45 PinB.3.4 Limitations & Restrictions B.3.3 Straight-Through Wiring for the 3H02-04B.3.5 Deﬁnitions INDEX Index FE Switch Module User GuideIndex-2