Manuals / Cabletron Systems / Computer Equipment / Switch

Cabletron Systems 3H02-04 Contents, Adding/Swapping Modules, Appendix A, Technical Specifications

Models: 3H08-04 3H02-04

1 42

Download 42 pages 24.72 Kb

Page 8

Contents

CHAPTER 6 ADDING/SWAPPING MODULES
6.1	Unpacking the Switch Module	6-1
6.2	Adding a Switch Module	6-1
6.3	Swapping a Switch Module	6-2

APPENDIX A		TECHNICAL SPECIFICATIONS
APPENDIX B		CABLES
B.1	Types/Connectors		B-1
B.2	Cable Specifications		B-1
B.3	Fast Ethernet Pin Assignments		B-2
	B.3.1	About RJ45 Connectors	B-2
	B.3.2 Crossover Wiring for the 3H02-04		B-3
	B.3.3 Straight-Through Wiring for the 3H02-04		B-4
	B.3.4	Limitations & Restrictions	B-4
	B.3.5	Definitions	B-4

INDEX

vi	FE Switch Module User Guide

Image 8

Cabletron Systems 3H02-04 Contents, Adding/Swapping Modules, Appendix A, Technical Specifications, Appendix B, Cables

Contents

FAST ETHERNET SWITCH MODULE 3H02-04 AND 3H08-04 USER GUIDE Page FE Switch Module User Guide FE Switch Module User Guide FCC NOTICEDOC NOTICE VCCI NOTICEEXCLUSION OF WARRANTY AND DISCLAIMER OF LIABILITY FE Switch Module User GuideCABLETRON SYSTEMS, INC. PROGRAM LICENSE AGREEMENT CABLETRON SOFTWARE PROGRAM LICENSEFE Switch Module User Guide UNITED STATES GOVERNMENT RESTRICTED RIGHTSCONTENTS CHAPTER 2 CONNECTING TO THE NETWORKCONFIGURING CHAPTER 5 DIAGNOSTICS AND TROUBLESHOOTINGContents TECHNICAL SPECIFICATIONSFE Switch Module User Guide CHAPTER 6 ADDING/SWAPPING MODULESCHAPTER INTRODUCTION 1.1 USING THIS MANUAL Chapter 1 Introduction1.3 3H02-04 FE SWITCH MODULE 1.2 OVERVIEW1.3.3 Ofﬂine Button 1.3.1 Connectors1.3.2 LEDs 1.4 3H08-04 FE SWITCH MODULE 1.4.1 Connectors1.4.2 LEDs 1.4.3 Ofﬂine Button1.5 DOCUMENT CONVENTIONS FE Switch Module User GuideThe following conventions are used throughout this document Chapter 1 Introduction1.6 RELATED MANUALS 1.7 GETTING HELPATX User Guide ATX MIB Reference Guide anonymousA description of the failure CHAPTER CONNECTING TO THE NETWORK 2.1 POWER-UP LED SEQUENCE2.2 CONNECTING TO A NETWORK 2.2.1 Connecting the 3H02-04 FE Switch Module2.2.2 Connecting the 3H08-04 FE Switch Module Figure 2-2 3H08-04 Front Panel ConnectionsPage Chapter 2 Connecting to the NetworkFE Switch Module User Guide CHAPTER CONFIGURING 3.1 CONNECTING THE LOCAL CONSOLE MANAGER 3.2 LOCAL CONSOLE MANAGER COMMANDS4.1 DISPLAYING SWITCH MODULE PORT STATUS CHAPTER MONITORINGDisabled - The port isn’t conﬁgured for Spanning Tree Total Collisions - number of collision during packet transmissions Page FE Switch Module User GuideChapter 4 Monitoring 5.2 POWER-UP RESULTS CHAPTER DIAGNOSTICS AND TROUBLESHOOTING5.1 POWER-UP TESTS 5.3 OPERATIONAL DIAGNOSTICS Chapter 5 Diagnostics and Troubleshooting5.4 DIAGNOSTIC RESULTS 5.5 TROUBLESHOOTING 5.5.1 If the Module Fails to Power Up5.5.2 Connectivity Problems CHAPTER ADDING/SWAPPING MODULES 6.1 UNPACKING THE SWITCH MODULE6.2 ADDING A SWITCH MODULE 6.3 SWAPPING A SWITCH MODULE 7. Tighten the screws on each side of the switch module’s front panel Page FE Switch Module User GuideChapter 6 Adding/Swapping Modules APPENDIX A TECHNICAL SPECIFICATIONS 3H02-04 B.1 TYPES/CONNECTORS B.2 CABLE SPECIFICATIONSAPPENDIX B CABLES FE Switch Module User GuideB.3 FAST ETHERNET PIN ASSIGNMENTS B.3.1 About RJ45 Connectors Figure B-1 RJ45 Connector Pin NumbersB.3.2 Crossover Wiring for the 3H02-04 Table B-5 Crossover RJ45 Wiring ConfigurationTable B-4 RJ45 Crossover Pin Assignments RJ45 PinB.3.5 Deﬁnitions B.3.3 Straight-Through Wiring for the 3H02-04B.3.4 Limitations & Restrictions INDEX Index-2 FE Switch Module User GuideIndex