Table of Contents | Grizzly G0453, G0454 specs

Table of Contents

INTRODUCTION	2
Manual Accuracy	2
Contact Info	2
Machine Description	2
Identification	3
Internal Components	4
G0453 Machine Data Sheet	5
G0454 Machine Data Sheet	7
SECTION 1: SAFETY	9
Safety Instructions for Machinery	9
Additional Safety Instructions for Planers....	11
SECTION 2: POWER SUPPLY	12
SECTION 3: SETUP	14
Needed for Setup	14
Unpacking	14
Inventory	15
Cleanup	16
Site Considerations	17
Lifting & Moving Base Unit	18
Assembly	18
Dust Collection	21
Check Gearbox Oil	21
Test Run	21
Re-Tension V-Belts	22
Recommended Adjustments	22
SECTION 4: OPERATIONS	23
Operation Overview	23
Planing Tips	24
Workpiece Inspection	24
Wood Hardness	25
Feed Rate	25
Depth of Cut	26
Bed Roller Height	26

SECTION 5: ACCESSORIES		28
SECTION 6: MAINTENANCE		30
Schedule		30
Cleaning & Protecting		30
Lubrication		31
SECTION 7: SERVICE		33
Troubleshooting		33
Setting/Replacing Knives		36
V-Belt Tensioning/Replacement		37
Table Height Chain Tension		39
Feed Rollers, Chip Breaker & Pressure Bar
Heights		40
Roller Spring Tension		43
Positioning Chip Deflector		43
Scale Calibration		44
Anti-Kickback Fingers		44
Pulley Alignment		45
SECTION 8: WIRING		46
Wiring Safety Instructions		46
G0453	Wiring Diagram	47
G0454	Wiring Diagram	48
SECTION 9: PARTS		49
G0453	Headstock	49
G0453	Table	51
G0453	Columns	52
G0453	Cabinet Stand	53
G0453	Gearbox	55
G0453	Label Placement	56
G0454	Headstock	57
G0454	Table	60
G0454	Columns	61
G0454	Cabinet Stand	62
G0454	Gearbox	64
G0454	Label Placement	65
WARRANTY AND RETURNS		69

Image 3

Grizzly G0453, G0454 owner manual Table of Contents

Contents

Model G0453/G0454 15 & 20 Mobile Planers Page Table of Contents Introduction Manual Accuracy Contact InfoMachine Description ON/OFF Identification Internal Components Machine Data Sheet Other G0454 Machine Data Sheet Knife Adjustment Jack Screws and Springs Safety Instructions for Machinery Safety Unattended OPERATION. Never leave Additional Safety Instructions for Planers G0453 220V Circuit Requirements Power SupplyAvailability Full-Load Current Rating G0454 Grounding InstructionsExtension Cords G0453 Description Qty SetupNeeded for Setup Unpacking Inventory Box Inventory Figure QtyG0454 Hardware and Tools not shown Cleanup Before cleaning, gather the followingBasic steps for removing rust preventative Site Considerations Assembly Lifting & Moving Base UnitTo assemble your planer Attaching magnetic switch Foot pedal and caster installed G0453/G0454 Mfg. Since 3/08 Check Gearbox Oil Dust Collection Test Run Recommended Adjustments Factory adjustments that should be verifiedRe-Tension V-Belts Operation Overview Operations Workpiece Inspection Planing Tips Species Hardness Wood Hardness Feed Rate Bed Roller Height Depth of Cut Disconnect Planer from Power To adjust the bed rollers G2790 Universal Knife Grinder Accessories G8982-Roller Table T20502 T20452 T20503 T20448 T20456 H0736 Maintenance Cleaning ProtectingSchedule Table Height Worm Gear LubricationFeed Roller Bushings Columns and Leadscrews Table Height Chain & Sprockets Drive Chain & SprocketsGearbox Oil Service TroubleshootingMotor & Electrical Amount of snipe Machine Operation Adjust the height of the chip breaker or pressure bar Setting/Replacing Knives To adjust the height of the knivesTools Needed Qty To tension/replace the V-belts Belt Tensioning ReplacementPage Table Height Chain Tension To adjust the table height chain tension Using a Rotacator Feed Rollers, Chip Breaker & Pressure Bar HeightsDist. Below Knife Edge at BDC Figure Adjustment Jam Nut Set Screw Using Wood Blocks To adjust the chip deflector gap Roller Spring TensionPositioning Chip Deflector Scale Calibration Anti-Kickback FingersTo re-position the scale To check/re-align pulleys Pulley Alignment Wiring Safety Instructions Wiring Magnetic ON/OFF Switch G0453 Wiring Diagram NHD BTH-21 G0454 Wiring Diagram Parts Description G0453 Headstock Parts List G0453 Table Breakdown G0453 Columns Breakdown G0453 Cabinet Stand Breakdown G0453 Cabinet Stand Parts List G0453 Gearbox Breakdown G0453 Label Placement G0454 Headstock Breakdown G0454 Headstock Parts List PN01M HEX NUT M6-1 PSS25M SET Screw M6-1 X PB09M G0454 Table Breakdown 310 G0454 Columns Breakdown G0454 Cabinet Stand Breakdown G0454 Cabinet Stand Parts List 538 G0454 Gearbox Breakdown G0454 Label Placement G0453/G0454 Mfg. Since 3/08 Comments Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC Warranty and Returns Warranty and Returns Order Hours a DAY