G0454 Label Placement | Grizzly G0453 specification

G0454 Label Placement

122

16

	16
121
118	7
	7

119

544

120

545

445

337

446

REF	PART #	DESCRIPTION

7	P0454007	SPEED CHANGE LABEL
16	P0453019	BELT COVER LABEL
118	PLABEL-37	RESPIRATOR/GLASSES LABEL VL
119	PLABEL-12	READ MANUAL LABEL VL
120	PLABEL-36	EAR PROTECTION LABEL VL
121	PLABEL-14	ELECTRICITY LABEL

REF	PART #	DESCRIPTION

122	P0454122	MACHINE ID LABEL
337	P0454337	GRIZZLY.COM LABEL
445	G8588	GRIZZLY NANEPLATE
446	P0454446	MODEL NUMBER LABEL
544	PPAINT-1	GRIZZLY GREEN TOUCH UP PAINT
545	PPAINT-11	GRIZZLY PUTTY TOUCH UP PAINT

Safety labels warn about machine hazards and ways to prevent injury. The owner of this machine MUST maintain the original location and readability of the labels on the machine. If any label is removed or becomes unreadable, REPLACE that label before using the machine again. Contact Grizzly at (800) 523-4777 or www.grizzly.com to order new labels.

G0453/G0454 (Mfg. Since 3/08)

-65-

Image 67

Grizzly G0453 owner manual G0454 Label Placement

Contents

Model G0453/G0454 15 & 20 Mobile Planers Page Table of Contents Manual Accuracy Contact Info IntroductionMachine Description ON/OFF Identification Internal Components Machine Data Sheet Other G0454 Machine Data Sheet Knife Adjustment Jack Screws and Springs Safety Instructions for Machinery Safety Unattended OPERATION. Never leave Additional Safety Instructions for Planers G0453 220V Circuit Requirements Power SupplyAvailability Full-Load Current Rating G0454 Grounding InstructionsExtension Cords G0453 Description Qty SetupNeeded for Setup Unpacking Box Inventory Figure Qty InventoryG0454 Hardware and Tools not shown Before cleaning, gather the following CleanupBasic steps for removing rust preventative Site Considerations Lifting & Moving Base Unit AssemblyTo assemble your planer Attaching magnetic switch Foot pedal and caster installed G0453/G0454 Mfg. Since 3/08 Check Gearbox Oil Dust Collection Test Run Factory adjustments that should be verified Recommended AdjustmentsRe-Tension V-Belts Operation Overview Operations Workpiece Inspection Planing Tips Species Hardness Wood Hardness Feed Rate Bed Roller Height Depth of Cut Disconnect Planer from Power To adjust the bed rollers G2790 Universal Knife Grinder Accessories G8982-Roller Table T20502 T20452 T20503 T20448 T20456 H0736 Cleaning Protecting MaintenanceSchedule Table Height Worm Gear LubricationFeed Roller Bushings Columns and Leadscrews Drive Chain & Sprockets Table Height Chain & SprocketsGearbox Oil Troubleshooting ServiceMotor & Electrical Amount of snipe Machine Operation Adjust the height of the chip breaker or pressure bar To adjust the height of the knives Setting/Replacing KnivesTools Needed Qty To tension/replace the V-belts Belt Tensioning ReplacementPage Table Height Chain Tension To adjust the table height chain tension Feed Rollers, Chip Breaker & Pressure Bar Heights Using a RotacatorDist. Below Knife Edge at BDC Figure Adjustment Jam Nut Set Screw Using Wood Blocks Roller Spring Tension To adjust the chip deflector gapPositioning Chip Deflector Anti-Kickback Fingers Scale CalibrationTo re-position the scale To check/re-align pulleys Pulley Alignment Wiring Safety Instructions Wiring Magnetic ON/OFF Switch G0453 Wiring Diagram NHD BTH-21 G0454 Wiring Diagram Parts Description G0453 Headstock Parts List G0453 Table Breakdown G0453 Columns Breakdown G0453 Cabinet Stand Breakdown G0453 Cabinet Stand Parts List G0453 Gearbox Breakdown G0453 Label Placement G0454 Headstock Breakdown G0454 Headstock Parts List PN01M HEX NUT M6-1 PSS25M SET Screw M6-1 X PB09M G0454 Table Breakdown 310 G0454 Columns Breakdown G0454 Cabinet Stand Breakdown G0454 Cabinet Stand Parts List 538 G0454 Gearbox Breakdown G0454 Label Placement G0453/G0454 Mfg. Since 3/08 Comments Warranty Card BOX BELLINGHAM, WA Grizzly INDUSTRIAL, INC Warranty and Returns Warranty and Returns Order Hours a DAY