21
BLOWER INSTALLATION
ELECTRICAL INSTALLATION TO BE DONE BY A QUALIFIED INSTALLER and must be connected and grounded in accordance with local codes. In the absence of local codes, use the current CSA C22.1 CANADIAN ELECTRICAL CODE in Canada or the current ANSI/NFPA 70 NATIONAL ELECTRICAL CODE in the United States.
| 1. Break out the blower and thermal | |
! WARNING | ||
disk | ||
Figure 37a |
2. Fish the wire extension through the blower
3.Ensure the thermodisc is touching the wall of the firebox. Secure the thermal disk assembly to the rear panel using
4of # 8 screws supplied. Figure 37b
4.Connect the variable speed switch to the jumper wire (installed in the stove) located just inside the larger knock out area. Figure 37b
5.Insert the blower assembly into the rear panel and secure using the
remaining #8 screws supplied.
| GS67 WIRING DIAGRAM |
| 6. Remove | the | ||
VARIABLE SPEED SWITCH |
|
| THERMAL DISK | switch housing, | ||
| LOCATED |
|
|
| c o n n e c t | t h e |
| IN WIRE |
|
|
| variable speed | |
| HOUSING |
|
|
| ||
|
|
|
|
| switch to the jumper | |
| JUMPER WIRE (installed in stove) |
| WIRE | wire and mount the | ||
VARIABLE |
|
|
| switch to the side | ||
SPEED |
|
|
| EXTENSION | ||
SWITCH |
|
|
|
| of the housing. | |
KNOB |
|
|
|
| ||
|
|
| WHITE |
| Attach and secure | |
|
|
|
|
|
| |
| RED |
|
|
| the variable speed | |
|
|
|
|
| ||
|
| WHITE | BLACK |
| switch using the nut | |
|
|
|
| provided. Reinstall | ||
|
|
|
|
| ||
|
| WIRE |
| the switch housing. | ||
|
| HARNESS |
| Install the variable | ||
|
|
| (included in GS67 kit) |
| s p e e d s w i t c h | |
| GREEN |
|
|
| ||
|
| TO |
| knob. |
| |
BLOWER | (GROUND) |
|
|
| ||
|
|
| POWER | FIGURE 36 |
| FIGURE 37b |
|
|
| SUPPLY |
|
NIGHT LIGHT™ REPLACEMENT
BULB REPLACEMENT
The GDS26 comes equipped with our “Night Light™”. If in the event the lamp or lens needs to be replaced, follow these instructions.
1.Turn off all electrical supply.
2.Remove the front and door from the firebox.
3.Unscrew the lens cover making sure the washer stays in place.
Note: Do not handle the lamp (bulb) with bare fingers, protect with a clean dry cloth.
4.The lamp will pull straight out of the socket. Replace with Wolf Steel Ltd. parts only
5.Replace lens with gasket, lense covers, attach wires to quick connects and replace the door when finished.
THE FIREBOX MUST BE SEALED.
FIGURE 38 When
LENS ASSEMBLY INSTALLATION
1. Remove the door from | KEY HOLE | FIGURE 39 |
the firebox. |
|
|
2.Run the wires up through the lens hole.
3.Align key hole with lens assembly.
4.Snap into place.
5.Replace light shields,
attach the wires and replace the door to the firebox.
LENS ASSEMBLY REPLACEMENT
1. Remove the front | FIGURE 40 |
door and top shield |
|
f r o m t h e f i r e b o x . |
|
2.Compress the retainer fins in with a screw driver while pressing firmly on the top of the light assembly.
3.Once all the retainer fins are pushed in the lens assembly will snap out of place.