BRIM-A6 Specifications, Related Manuals, Emi | Cabletron Systems

Chapter 1: Introduction

1.5 BRIM-A6 SPECIFICATIONS

This section describes environment speciﬁcations and safety requirements for the BRIM-A6. Cabletron Systems reserves the right to change these speciﬁcations at any time without notice.

Environment	5°C to 40°C (41°F to 104°F)
Operating Temperature:	5°C to 40°C (41°F to 104°F)
Storage Temperature:	-30°C to 90°C (-22°F to 194°F)
Operating Humidity:	5% to 95% (non-condensing)

Safety

This unit meets the safety requirements of UL1950, CSA C22.2 No. 950, and EN60950.

EMI

This unit meets the EMI requirements of FCC Part 15 Class A, EN55022 Class A and VCCI Class I.

EMC

This unit meets the EMC requirements of EN 50082-1 including: IEC 801-2 (ESD), IEC 801-3 (Radiated Susceptibility), and IEC 801-4 (EFT/B).

1.6 RELATED MANUALS

Use the following manuals to supplement the procedures and other technical data provided in this manual. This manual references procedures in these manuals, where appropriate, but does not repeat them.

Cabletron Systems EMM-E6 User’s Guide

Cabletron Systems ESXMIM Installation Guide

Cabletron Systems MicroMMAC User’s Guide

Cabletron Systems NBR-620/420/220 Installation Guide and NBR-620/420/220 Local Management Guide

Page 1-4

BRIM-A6 User’s Guide

Image 12

Cabletron Systems manual BRIM-A6 Specifications, Related Manuals, Emi, Emc

Contents

BRIM-A6 USER’S Guide BRIM-A6 User’s Guide FCC Notice DOC NoticeVcci Notice Exclusion of Warranty and Disclaimer of Liability Cabletron SYSTEMS, INC. Program License AgreementCabletron Software Program License United States Government Restricted Rights Declaration of Conformity Contents Viii BRIM-A6 User’s Guide Using this Manual Chapter Introduction Document Conventions Following conventions are used throughout this document BRIM-A6 Features BRIM-A6 Overview BRIM-A6 Specifications Related ManualsEMI EMC Getting Help Chapter Installation Unpacking the Brim Installing Apims Installing an Apim Installing Brims Installing a Brim in a MIM Removing the Brim Coverplate Installing a Brim in a Hub BRIM-A6 User’s Guide Chapter Local Management Local Management Keyboard Conventions Keyboard Conventions Function Using LIM to Create PVCs ATM Connection Tables Screen ATM Connection Tables Screen Fields ATM Connection Tables Screen Commands Using ATM Connection Tables Screen Commands Adding PVCs to the Connection Tables Screen Deleting PVCs from the Connection Tables Screen Using LM to Create Pvcs BRIM-A6 Setup Screen BRIM-A6 Setup Screen Fields VPIVCI BRIM-A6 Setup Screen Commands Using BRIM-A6 Setup Screen Commands Accessing the BRIM-A6 Add/Delete Entry Screen BRIM-A6 Add/Delete Entry Screen Fields BRIM-A6 Add/Delete Entry Screen Commands Adding a PVC Modifying a PVC Deleting a PVC Chapter BRIM-A6 LEDs Apim LEDs Describes each of the Apim LEDs Appendix a Apim Specifications APIM-11 SpecificationsAPIM-21 Specifications APIM-22 Specifications APIM-29 Specifications APIM-67 Specifications BNC Appendix B ATM Overview ATM Basics ATM Cell Figure B-1 ATM Cells BRIM-A6 User’s Guide B-3 ATM Network Virtual Channels and Virtual Paths Permanent and Switched Virtual Channels ATM Protocol B-6 BRIM-A6 User’s Guide BRIM-A6 User’s Guide B-7 B-8 BRIM-A6 User’s Guide