8005 and 9005 Electronic Control Operation

15

When first powered up, the electronic system will perform a self-diagnostic check and then it will automatically heat to and maintain a temperature of 37.5˚C until you change the set temperature as listed in the “Temperature Adjustment” section below.

These instructions will describe features and options that your particular spa may not be equipped with.

Initial Start-up

When your spa is first powered up, it displays some configuration codes and

then goes into priming mode (Pr will appear on the display panel). This mode lasts up to four minutes and then the spa begins to heat to its pre -programmed temperature of 37.5˚C. You can exit the priming mode early by pressing UP or DOWN buttons.

3.Press MODE/PROG to confirm selection.

Standard Mode: This is programmed to maintain the desired temperature. Note that the last measured spa temperature displayed is current only when the pump has been running for at least two minutes. The “STAND” icon will display until the mode is changed.

OperatingYour Spa

Temperature Adjustment (26.0˚C - 40.0˚C)

The start-up temperature is set at 37.5˚C. The last measured temperature is constantly displayed on the control panel. Note that the last measured spa temperature is displayed. The displayed temperature will be updated when the pump has been running for at least two minutes.

Press the UP or DOWN buttons once to display the set temperature. Each time either button is pressed again, the set temperature will increase or decrease depending on which button is pressed. After three seconds, the control panel will automatically display the last measured spa temperature.

Time

When time hasn’t been programmed, the TIME icon flashes. To set the time, press the TIME button and then the MODE/PROG button. Use the UP and DOWN buttons to adjust time. See the next page for more detailed instructions.

Standard, Economy, Sleep, and Standby Modes

Mode/Prog: This button is used to switch between standard, economy, and sleep modes.

1.Press MODE/PROG to enter mode programming.

2.Press the DOWN button to cycle through to the desired mode.

Economy Mode: Economy mode heats the spa to the set temperature only during filter cycles. The “ECON” icon will display until the mode is changed. Pressing the JETS 1 button while in economy mode puts the spa in standard-in-economy mode, which operates the same as standard mode but reverts back to economy mode automatically after one hour. During this time, pressing the MODE/PROG button will revert to economy mode immediately.

Sleep Mode: Sleep mode heats the spa to within 11˚C of the set temperature only during filter cycles. The “SLEEP” icon will display until the mode is changed.

Standby Mode: Pressing “Warm” or “Cool” then “Jets 2” will turn off all spa functions temporarily. This is helpful when changing a filter. Pressing any button resets the spa.

Jets 1 and Jets 2

Press the JETS 1 button once to turn pump 1 on or off and to shift between low and high speeds if equipped. If left running, the low speed turns off after two hours and the high speed turns off after 15 minutes. On non-circulation systems, the low speed of pump 1 runs when the blower or any other pump is on. It may also activate for at least two minutes every 30 minutes to detect the spa temperature and then to heat to the set temperature if needed, depending upon the mode. When the low speed turns on automatically, it cannot be deactivated from the panel; however, the high speed may be started.

2010 Portable Spa

LTR20101001, Rev. B

www.calspas.com

Page 14 Page 16
Page 15
Image 15
Cal Spas LTR20101001 manual Electronic Control Operation, OperatingYour Spa
Page 14 Page 16

LTR20101001 specifications

Cal Spas LTR20101001, a model that exemplifies luxury and relaxation, offers an impressive combination of features and technologies designed to enhance the spa experience. This portable hot tub is perfect for those looking to enjoy therapeutic benefits in the comfort of their own backyard.

One of the standout features of the Cal Spas LTR20101001 is its spacious seating capacity. Designed to accommodate up to five people, this spa promotes social interaction and creates an inviting atmosphere for family and friends. The ergonomic seating ensures comfort during use, allowing users to fully unwind while enjoying the soothing effects of the water.

The LTR20101001 hot tub is equipped with powerful jets strategically placed throughout the interior. These jets provide targeted hydrotherapy, which is beneficial for muscle relaxation and stress relief. The combination of adjustable jet intensities allows users to customize their spa experience according to their preferences. This versatility is a key characteristic that sets the LTR20101001 apart from other models in the market.

In terms of technology, the spa includes an advanced control system that enables users to easily manage settings such as temperature and jet configurations. The user-friendly interface ensures that even those new to hot tub ownership can operate it with ease. Additionally, the model features energy-efficient insulation and a quiet, reliable heater that maintains optimal water temperature without driving up energy costs.

The Cal Spas LTR20101001 also prioritizes safety and durability. It is constructed with high-quality materials that are resistant to fading and cracking. The spa includes built-in safety features like a locking cover and non-slip surfaces to prevent accidents during entry and exit.

Lastly, the aesthetic appeal of the LTR20101001 cannot be overlooked. With a range of color options and stylish designs, it can easily complement any outdoor setting. The spa's modern look adds a touch of sophistication to backyards, patios, or decks, making it not only a place for relaxation but also an attractive addition to outdoor spaces.

Overall, the Cal Spas LTR20101001 embodies a perfect blend of comfort, technology, safety, and style, making it an exceptional choice for anyone looking to elevate their outdoor leisure experience.
Top Page Image Contents