Operating Instructions & Parts Manual | HVLP Spray Gun |
|
|
Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety information. Failure to comply with instructions could result in personal injury and/or property damage! Retain instructions for future reference.
HVLP Spray Gun
Attention: Campbell Hausfeld recommends that servicing other than that shown in the instruction manual should be performed by an authorized service facility.
Description
High volume, low pressure (HVLP) paint sprayers are designed to deliver a fine finish with low overspray. The sprayer can be used to apply various acrylics, stains, sealers, lacquers, latexes, and primers. This unit can be used for painting cabinets, furniture, machinery, equipment, walls and trim work. Spray- ers of this type are not recommended for automotive final coat. This portable unit is an ideal alternative to convention- al spray guns. The HVLP’s high transfer efficiency provides professional results with much less material waste and envi- ronmental contamination than other conventional spray painting systems.
Unpacking
When unpacking the sprayer, inspect carefully for any damage that may have occurred during transit. Make sure any loose fittings, bolts, etc., are
| Quick Connect Fitting |
| Air Flow Control |
Oval To Round | Material Flow |
Control Knob | |
Pattern Adjustment |
|
| Locking Lever For |
| |
| 1 Quart Cup |
Figure 1 - Features |
|
tightened before putting sprayer into service. Each sprayer has been tested before shipment.
NOTE: The packing nut may need additional adjustment due to the packing material relaxing during shipment.
The fluid used for testing the sprayer has been drained, but some of this fluid will remain in the spray gun. This fluid should be flushed from the spray gun to prevent contamination of the coating material. Use a solvent compatible with the coating to be sprayed.
Table Of Contents
Description . . . . . . . . . . . . . . . . . . . . 1
Unpacking. . . . . . . . . . . . . . . . . . . . . 1
General Safety
Danger means a
! DANGER hazard that will cause death or serious injury if the warning is ignored.
Warning means a hazard that could cause death or serious injury if the warning is ignored.
Caution means a hazard that may cause
minor or moderate injury if the warning is ignored. It also may mean a hazard that will only cause damage to property.
Notice means any
NOTICE additional information pertaining to the product or its proper usage.
Paints and solvents containing HALOGENATED HYDROCARBONS can react explosively with aluminum. Always check the product’s label before using these materials in the unit.
Make sure the room is
Avoid all ignition sources, such as static electricity sparks, open flames, hot objects, sparks from connecting and disconnecting power cords, and working light switches.
Follow the material and solvent manufacturers’ safety precautions and warnings. Do not use liquids with flash points less than 100 degrees Fahrenheit (38 degrees Celsius).
Do not carry TURBINE while spraying.
Keep the turbine at the maximum distance from the spraying area.
General Safety Information. . . . . . . 1
Operation . . . . . . . . . . . . . . . . . . . . . 4
Troubleshooting . . . . . . . . . . . . . . . . 6
Warranty. . . . . . . . . . . . . . . . . . . . . 10
Read all instructions and safety precautions before operating the unit.
!WARNING ofRiskfire
or explosion! Solvent and paint fumes can explode or ignite, causing severe injury and property damage.
Static electricity can be produced by HVLP spraying. Make sure any electrically conductive object being sprayed is grounded to prevent static sparking. The sprayer is grounded through the electric cord. If an extension cord is necessary, the cord must be a grounded, 115 volt, three wire type cord.
©2007 Campbell Hausfeld/ Scott Fetzer | IN206701AV 9/07 |
For parts, product & service information
visit www.chpower.com
