Control Block Cannot be Accessed for ONE

KN3CV136	VALID RANGE IS 10–3600
	Explanation: The automatic screen refresh interval must be in the range of 10–
	3600 seconds.
	System Action:	None.
	User Response: Specify a number that is not less than 10 and is not greater
	than 3600.
	Message Type:	User input error.
KN3CV137	THE CONTROL BLOCK CANNOT BE ACCESSED FOR ONE OF THE
	FOLLOWING REASONS:
	1. THE CONTROL BLOCK IS NO LONGER VALID.
	2. AN ATTEMPT TO ACCESS THE ADDRESS SPACE FAILED
	Explanation: The control block is not available for display because the control
	block address is no longer valid, or an attempt to swap in the address space failed.
	System Action:	None.
	User Response:	Press Enter to continue.
	Message Type:	Information.
KN3CV138	THE ADDRESS SPACE HAS TERMINATED
	Explanation: The control block data is not available for display because the
	address space is gone.
	System Action:	None.
	User Response:	Press Enter to continue.
	Message Type:	Information.
KN3CV139	THE ADDRESS SPACE IS BEING SWAPPED IN, TRY AGAIN LATER
	Explanation: The control block data is not available for display because the
	address space is being swapped in.
	System Action:	None.
	User Response: Press Enter to continue. Try to access the data at a later time,
	after the address space has been swapped in.
	Message Type:	Information.
KN3CV140	THERE WAS NO RPL CONTROL BLOCK FOUND FOR THIS SESSION
	Explanation: Due to the transient nature of control blocks, an RPL with a CID
	matching this session's CID could not be found. The data cannot be displayed.
	System Action:	None.
	User Response:	Press Enter to continue.
	Message Type:	Information.
KN3CV141	UNABLE TO DISPLAY THE CONTROL BLOCK DATA. CHECK THE
	MESSAGE LOG FOR MORE INFORMATION
	Explanation: An error occurred while trying to display the requested data
	System Action:	None.
	User Response: Press Enter to continue. Note the OMEGAMON II collector's
	return and sense codes, on the message log or OMEGAMON II's SYSOUT, and
	report them to Candle Support Services.
	Message Type:	Internal error.

356 Candle Products Messages Manual (KLVHS–KONCT)

Page 356

Image 356

Candle GC32-9172-00 manual Control Block Cannot be Accessed for ONE, Following Reasons, Control Block is no Longer Valid

GC32-9172-00 specifications

The Candle GC32-9172-00 is a state-of-the-art device that has gained significant recognition in the technology landscape due to its innovative features and exceptional performance. This product stands out for its ability to meet the demanding requirements of modern users, providing a seamless experience across various applications.

One of the foremost features of the GC32-9172-00 is its advanced processing power. Equipped with a high-performance processor, the device is designed to handle complex tasks efficiently, enabling users to run multiple applications simultaneously without experiencing slowdowns. This makes it particularly attractive for both professionals and enthusiasts who need reliability in performance.

In terms of connectivity, the GC32-9172-00 incorporates cutting-edge wireless technology, ensuring that users remain connected at all times. The device supports a range of wireless protocols, facilitating smooth communication with other gadgets and networks. Its robust connectivity options allow for quick data transfer, enhancing productivity and streamlining workflows.

The design of the Candle GC32-9172-00 is another highlight. With a sleek and modern aesthetic, it not only looks appealing but is also ergonomically crafted for user comfort. The user interface is intuitive and easy to navigate, making it accessible for individuals of all technical skill levels. The display is vibrant and responsive, providing an immersive experience whether used for work or entertainment.

Moreover, energy efficiency is a key characteristic of the GC32-9172-00. It utilizes advanced technologies to minimize power consumption while still delivering high performance. This eco-friendly approach not only helps reduce electricity bills but also supports sustainability initiatives, making it a responsible choice for environmentally conscious users.

Security features are paramount in today’s digital landscape, and the Candle GC32-9172-00 does not disappoint. It is equipped with top-notch security technology to safeguard user data and ensure privacy. With built-in encryption protocols and regular software updates, users can trust that their information is well-protected against potential threats.

In conclusion, the Candle GC32-9172-00 is a versatile and high-performing device that encapsulates the needs of today’s users. With its powerful processing capabilities, exceptional connectivity, ergonomic design, energy efficiency, and robust security features, it stands out as a preferred choice in the market. Whether for professional applications or personal use, the GC32-9172-00 exemplifies the perfect blend of technology and innovation.

Contents

Candle Products Messages Manual Volume Candle Products Messages Manual KLVHS-KONCT Contents Candle Products Messages Manual KLVHS-KONCT KLVHS001 Handle Services Manager Initialization Complete KLVHS002KLVHS005 Klvinhsm Rkanpar Parameters KLVHS006 KLVHS203 Handle Services Manager Vector Table is Invalid KLVHS011KLVHS201 KLVHS202 No Handle Pools Available Error KLVHS811 Handle Services Manager Global StatisticsKLVHS205 Invalid Release Handle Request Info KLVHS821 Handle Services Manager Global Statistics Detail KLVHS817KLVHS818 KLVHS822 KLVHS831 Handle Services Manager List Ownerid Statistics KLVHS841 Handle Services Manager List Poolid StatisticsKLVHS830 KLVHS832 KLVHS843 KLVHS844Handles KLVHS845 KLVHS854 KLVHS855KLVIC001 KLVIC002 KLVIN403 Command Library Unavailable KLVIN000 CT/IX Interface InitializedKLVIN000 KLVIN001 KLVIN406 KLVIN407 Flushing Initial MessagesKLVIN408 KLVIN409 Initialization Library Unavailable KLVIP003 Unsupported IPC Service KLVIN412KLVIN413 KLVIN414 KLVLI001 Lock Manager Integrity Error KLVLR003 Logical Resource Integrity ErrorKLVLR004 PURGE/CLEANUP Exit Error DETECTED, Dump Requested Alert KLVLR006 Logical Resource Control Block Error KLVLR005KLVLW001 KLVLW002 KLVLW003 KLVLW004KLVLW011 Dynamic Allocation Values KLVLW012 KLVLW031 Rklvlog Switch Requested KLVLW022KLVLW023 KLVLW027 Copies Must be Between 1 KLVLW041 Rklvlog Dataset Disabled by Permanent Error KLVLW081KLVLW082 KLVLW083 KLVNA003 Database INACCESSIBLE, no Vsam LSR Resources KLVNA001KLVNA002 KLVNA004 KLVNA006 KLVNA007KLVNA008 Klvinnam Rkanpar Parameters KLVNA009 KLVNA012 KLVNA013KLVNA014 KLVNA015 KLVNA017 KLVNA018KLVNA019 KLVNA020 KLVNA021 KLVNA022KLVNA023 KLVNA031 KLVNA034 Database Allocation Failed Resource Error KLVNA035KLVNA036 Control Point Options not Valid with VALIDATE= KLVNA037 KLVNA103 KLVNA101KLVNA102 Current Password Expired CNTRLPTcntrlpt USERIDuserid NEW Password Invalid CNTRLPTcntrlpt USERIDuseridKLVNA104 GROUPgroup TERMterminal APPLappl User Access Revoked CNTRLPTcntrlpt USERIDuserid KLVNA106User not Defined to Group CNTRLPTcntrlpt USERIDuserid KLVNA107 Group Access Revoked CNTRLPTcntrlpt USERIDuserid KLVNA108KLVNA109 Terminal not Authorized CNTRLPTcntrlpt USERIDuserid KLVNA110 Application not Authorized CNTRLPTcntrlpt USERIDuseridKLVNA111 Operator not Authorized CNTRLPTcntrlpt KLVNA112 KLVNA113 KLVNA114 KLVNA151KLVNA251 KLVNA252 KLVNA253 Resource List Build DISABLED, not APF Authorized KLVNA254KLVNA255 KLVNA256 Refresh of Resource Profiles Complete KLVNT002 KLVOP001KLVOP002 KLVOP003 KLVOP005 KLVOP006KLVOP007 KLVOP008 KLVOP012 Active Resource List KLVOP022KLVOP023 KLVOP024 KLVOP025 KLVOP026KLVOP027 KLVOP028 Confirmation not RECEIVED, Shutdown Bypassed KLVOP032 Zero Interval not Allowed on Every Command KLVOP031KLVOP033 Time Interval Greater than 240000 Specified KLVOP041 KLVOP044 KLVOP046KLVOP052 KLVOP053 IDoperator DEVdev PENDpendnum KLVOP102 KLVOP103KLVOP111 KLVOP112 KLVOP124 Internal Trace Facility Disabled KLVOP122KLVOP123 KLVOP125 Trace Request REJECTED. Required Argument Missing KLVOP130 GTF Interface has not Been Enabled KLVOP129Terminal KLVOP131 Trace Classinttermacbdlg Status KLVOP142 KLVOP143KLVOP152 KLVOP161 KLVOP165 KLVOP182KLVOP183 Emulation Session Started KLVOP184 KLVOP191 KLVOP192For Autopurge KLVOP193 KLVOP194 Resource Name is Required KLVOP195KLVOP201 Anyappl Specified in a NON Dedicate Pool Ignored KLVOP202 KLVOP205 KLVOP207KLVOP208 KLVOP209 Sesslim Specified in a NON Dedicate Pool Ignored KLVOP210 Nocappl Specified in a NON Dedicate Pool Ignored KLVOP211KLVOP290 KLVOP291 KLVOP303 Viewlog Cluster not Accessible KLVOP314 Command IssuedKLVOP302 Viewlog Cluster not Available KLVOP304 KLVOP402 KLVOP403 Unable to Open JES Spool FileKLVOP404 KLVOP405 KLVOP503 No Text Passed to the MVS Command KLVOP502KLVOP552 KLVOP553 KLVOP555 KLVOP601 VPO Facility not AvailableKLVOP651 KLVOP652 KLVOP655 KLVOP656KLVOP657 KLVOP658 KLVOP803 KLVOP804KLVOP805 KLVOP809 Print Request Accepted KLVOP853 KLVOP854KLVOP855 KLVOP856 KLVOP901 NAM Inactive KLVOP902KLVOP903 KLVOP904 KLVOP908 KLVOP909KLVOP910 KLVOP911 User userid Defined date time KLVOP922 KLVOP923KLVOP924 KLVOP926 KLVOP930 KLVOP951 SCB DumpKLVOP953 KLVOP960 KLVOP963 Command ERROR, RTM Interface MAY be SET on or OFF KLVOP964KLVOP965 KLVOP966 KLVOP972 GTF Interface Disabled KLVOP973 Command ERROR, GTF Interface MAY be SET on or OFFKLVOP968 KLVOP969 KLVOP975 KLVPA001KLVPA002 KLVPA003 KLVPA004 KLVPA005KLVPA006 No Valid Request Coded for Functionpds KLVPA007 KLVPM005 PSM Buffer Integrity Error KLVPM001KLVPM003 KLVPM010 Modname,attentioncode,fdbk, errordata,datastream KLVPM011KLVPM012 PSM Private Extension not Initialized KLVPM013 PSM ERP Info Block Pointer is Zero Candle Products Messages Manual KLVHS-KONCT LOG KLVPM051 Klvinpsm Rkanpar ParametersKLVPM052 KLVPM052 KLVPM101KLVPT001 KLVRE001 Gcsdisks Refreshed KLVRE004 KLVRE005KLVRE006 KLVRE008 User Response Depends on resulttext KLVRE009Sense Code Table Refresh from dsnamemember resulttext KLVRM004 Logical Resource Exit Stack Integrity Error KLVRT001 Parameter ErrorKLVRS001 Invalid $RSS Request KLVRS002 Invalid RSS Release Request KLVRT011 NPM Module Fnmnsi Requires APF Authorization KLVRT013 $STG ErrorKLVRT014 Parameter Error KLVRT012 Unable to Load NPM Module Fnmnsi KLVRT022 RTM NPM Vector Error KLVRT020KLVRT021 KLVRT023 RTM NPM NSI Address Space not Running KLVRT030 $STG Error KLVRT031 Parameter ErrorKLVSC001 KLVSC002 KLVSC004 KLVSC005KLVSC006 KLVSC007 KLVSC009 Invalid Time Specification KLVSC008Ambiguous Keyword Reference keyword Environmentalinformation SIZErange USEusecnt TOTALtotcnt ACCESSEDacccnt KLVSD001 Primary Main Storage InformationKLVSD002 Extended Main Storage Information KLVSD003 Allocation Detail KLVSD005 LIMITstolim SLOPEsl SIZESrange TOTALtotKLVSD006 FREEfree CARVEDcarved OVERHEADovhead KLVSD007 pp% is in USE tt% Allowed Threshold Exceeded Message Type Reply KLVSD021 TMSnum PREFIXpfx CUSHIONcshnKLVSD031 Buffer Pool Information KLVSD032 KLVSD033 Buffers INUSEinuse MAXmax GETSgets FREESfreesKLVSD034 Segments INUSEinuse MAXmax GETSgets FREESfrees Qq KLVSD039 END of Buffer Pool Information KLVSD101 Main Storage Scan StartedKLVSD102 Main Storage Scan Ended KLVSD103 KLVSD106 Insufficient Storage to Process Command KLVSD104NAME.... SIZElength TOTALcount KLVSD105 KLVSD108 Storage Integrity ERROR. Scan Terminated KLVSE051 Default Sense Code Table DefinedKLVSD107 KLVSE052 KLVSE055 User Sense Code Table Defined KLVSE056KLVSE057 KLVSE058 KLVSE059 Sense Table TOO LARGE, Ignored KLVSE061KLVSE062 KLVSE063 Klvinsns Rkanpar Parameters KLVSE064 KLVSI001Rkanparklvinstg KLVSI002 Parameters KLVSI030 Control Block Error During GET KLVSI040 Control Block Error During FreeKLVSI022 Invalid Storage Class on Terminate Request KLVSI031 Invalid Storage Class During GET KLVSI043 Storage Integrity Error KLVSI050 Control Block Error During USE/DROPKLVSI051 Logic Error During USE/DROP KLVSI041 Zero Address on Free Request KLVSP001 $SPS Invocation or Internal Error KLVSP002 $SPS String Length InvalidKLVSQ000 Is in Effect KLVSS002 KLVSS003KLVSS004 KLVSS005 KLVST001 Candle Engine Initialization ERRORS, Abend U0012 KLVST005 MVS Jobstep Authorization RequiredKLVST002 TSO Option Invalid for NON-TSO Address Space KLVST003 KLVST007 Bldvrp Failed for Vsam LSR Buffer POOL, RC=rc KLVST014 Invalid Trace Specification KLVST016 Invalid Event SpecificationKLVST012 Extended Main Storage Unavailable KLVST013 Extended Reserved Main Storage Unavailable KLVST020 LIMIT/GRANULE Option Specification Error KLVST018 Unable to Open Rklvlog DatasetKLVST019 Unable to Open Rklvsnap Dataset KLVST021 LOG Buffer Storage Unavailable Transient Already Resident Relocation Error Bldl KLVST024 Free Storage List UnavailableKLVST025 Unable to Identify Subtask Entrypoint KLVST026 KLVST028 KLVST029 Invalid Value for Slope ParameterKLVST030 Unable to Determine CPU Identification KLVST032 Percentage is Invalid in Quiesce Parameter KLVST038 Steplib Authorization Required KLVST036KLVST037 Component Begin Vectors Differ from Previous Elements KLVST041 Error Initializing Sysmdump Dataset KLVST040KLVST042 KLVST043 Unable to Open Rkanpar Dataset KLVTB001 KLVTB002KLVTB003 KLVTB004 KLVTB007 Unable to Access Table Cluster KLVTB006 No LSR Pool AllocatedKLVTB008 Unable to Read Table Database Control Record KLVTB009 Unable to Write Table Database Control Record KLVTB012 KLVTB013KLVTB014 KLVTB015 KLVTB017 KLVTB018KLVTB019 KLVTB020 KLVTB026 Unable to Access Table Cluster KLVTB021KLVTB022 KLVTB023 KLVTB027 KLVTB028KLVTB029 KLVTB030 KLVTB032 KLVTB033KLVTB034 KLVTB035 KLVTB038 KLVTB036KLVTB037 KLVTB040 Klvtbmgr Logic Error KLVTB039KLVTB041 Klvtbmgr Invalid Table Delete Pointer KLVTB042 Free $TUB Integrity Check Failed KLVTB045 KLVTB046KLVTB047 KLVTB048 Invalid Erase Request Detected KLVTB049 Invalid RLB Chain Detected KLVTB051 UNSUPPORTED/INVALID $TBHLP Request ReceivedKLVTB052 Klvintb Rkanpar Parameters KLVTB053 KLVTI201 Invalid $STMX Request Detected KLVTQ101KLVTQ102 KLVTR001 Internal Trace Status KLVTR004 Internal Trace Facility Disabled DisabledKLVTR003 KLVTR005 KLVTR026 GTF Interface has not Been Enabled KLVTR022KLVTR024 KLVTR025 KLVTS001 Timer Already Cancelled KLVTS011 Timer Association Vector ReuseKLVTR031 KLVTR032 END of Trace Status KLVVL001 Vsam Services not Available for Viewlog KLVVL002KLVVL003 KLVVL004 Unable to Reopen Viewlog Cluster KLVVL007 KLVVL008KLVVL009 KLVVL010 KLVVL012 KLVVL013 Rkanparklvinvlg is EmptyKLVVL014 Dsname or Ddname is Required for Viewlog KLVVL015 KLVVL017 KLVVM001KLVVM002 KLVVP000 KLVVP014 KLVVP015 Maxline Parameter not in RANGE1-255KLVVP017 KLVVP018 KLVVP019 KLVVP020KLVVP022 KLVVP023 KLVVP035 KLVVP032KLVVP034 KLVVP036 KLVVP037KLVVP038 Interrupted KLVVP201 VPO Terminated KLVVP202 VPO TerminatingKLVVP300 KLVVP301 KLVVP305 Print Request Status Flags KLVVP306 SESS-VPRTLOGGED-ONKLVVP307 Actively Printing KLVVP308 Intervention Required Sent to Application KLVVP311 Term Request Requires a Specified Vprinter KLVVP312KLVVP313 KLVVP314 Vrpinter Request Token Contains Invalid Characters KLVVP400 KLVVP401KLVVP402 KLVVP403 KLVVP406 Retry in Progress YES/NO KLVVP407 No Retry Limit SpecifiedKLVVP408 Retries Left ## KLVVP409 Alternate Physical Printer Attempted YES/NO KLVVP411 Session Honors Relreq YES/NO KLVVP412 Wait for DR from Physical Printer YES/NOKLVVP413 Outbound Limit Reached YES/NO KLVVP414 Immediate Physical Release Specified YES/NO KLVVP416 KLVVP417 Physical Printer OWNEDYES/NOKLVVP418 Maxline ### KLVVP419 KLVVP422 KLVVP423 Physical Printer is Sysout YES/NOKLVVP424 KLVVP425 KLVVP427 KLVVP428 Sysout Ignore EOM YES/NOKLVVP429 No Vprinters Defined KLVVP430 Vprt and Pprt MAY not be Specified Together KLVVS010 KLVVS002KLVVS003 KLVVS011 ScheduledKLVVS012 KLVVS013 WARN, Error KLVVS016Increase &$CCBSP$ KLVVS017 KLVVS031 KLVVS021KLVVS026 KLVVS041 KLVVS042KLVVS043 KLVVS050 KLVVS051 KLVVS052 Invalid Klvvsstm RequestKLVVT001 KLVVT002 KLVVT004 Vtam Access Method Support Vector List KLVVT005KLVVT015 KLVVT021 Appl Request Retry KLVVT021 Definite Response KLVVT021 Exception ResponseExplanation An exception response was received by CT/Engine KLVVT021 Physical Error KLVVT021 API Exit Trace EnabledKLVVT021 RPL Exit Trace Enabled KLVVT021 Vtam Lerad Exit KLVVT031 KLVVT051KLVVT061 KLVVT062 KLVVT101 KLVVT102KLVVT103 KLVVT104 KLVVT106 KLVVT107KLVVT108 KLVVT109 KLVVT111 Increase &$ARBSP$KLVVT113 Klvinvtm Rkanpar Parameters KLVVT114 KLVVT251 KLVVT501 Initialization Member Klvinvpo not AvailableKLVVT503 Initialization Member Klvinvpo is Empty KLVVT505 KLVVT506 KLVVT507KLVVT508 KLVVT509 VPO Applid is not Authorized AS a Program Operator KLVVT511 KLVVT512 Klvinvpo Rkanpar ParametersKLVVT513 KLVVT851 Cancelled KLVVT902KLVVT903 KLVVT904 KLVVT953 KLXCP001Warn KLXCP002 Subsys Configuration content of member Syntax Error msg textKLXIN001 Explanation KLXIN003 TCP/ACCESS Interface Configuration Complete KLXIN004 TCP/ACCESS Interface Initialization BypassedKLXIN003 TCP/IP Interface Initialized KLXIN004 TCP/IP Interface not Opened RC9999 KLXIN006 KLXIN007KLXIN008 KLXIN009 Hpns Initapi Failed Rcffffffff ERRNO000003F3 Text in error KLXOP004 KLXOP004 TCP/IP’,SUBCMD,’ CompletedKLXOP005 Rc Hostname hostname KM2HDI80 CANSM2HD Terminated by Stop Command KM2EXPFF Profile Export FailedKM2EXP00 Profile Export Completed Successfully KM2HDI00 Historical Data Interface Initialized KM2HDI99 CANSM2HD Failed KM2HDI99 Reason xxxx Session xxxxxxxx Handle KM2IMPFF Profile Import Failed KM2IMP00 Profile Import Completed Successfully KMC0010E Your request failed. Message format not valid KMC0011E Your request failed. Gets inhibited for the queue KMC0021E Your request failed. MQSeries object already exists KMC0024E Your request failed. MQSeries pageset error KMC0022E Your request failed. MQSeries object damagedKMC0023E Your request failed. MQSeries object in use KMC0025E Your request failed. MQSeries pageset full KMC0028E Your request failed. MQSeries queue deleted KMC0029E Your request failed. MQSeries queue is full KMC0037E Your request failed. MQSeries security error Converted is not valid or not supported KMC0045E Your request failed. Unknown MQSeries queue name Attribute of the definition But it does not have a Usage attribute of Mqustransmission SYSTEM.ADMIN.COMMAND.QUEUE for distributed platforms or SYSTEM.COMMAND.INPUT for MVS is large enoughIs not valid 194,304 KMC0097E Your request failed. MQSeries object name not valid KMC0103E Your request failed. MQSeries send failed KMC0104E Your request failed. MQSeries received data errorKMC0101E Your request failed. MQSeries connection refused Channel is in doubt To resolve the in-doubt state, or resolve the channel KMC0120E Your request failed. MQSeries channel name invalid Maximum length of the name depends on the environment User Response Specify a valid name for the message exit Channel types, but is not present User Response Specify the Connection Name for the channel TCP NetBIOSSPX Maximum length of the string is 128 characters Working correctly, at both endsOn OS/2 Warp, Windows, and Windows NT, it is of the form KMC0153E Queue Manager is already a member of this cluster Queue Manager cannot be deleted by the Configuration Agent At least at version 5.1 distributed platforms or 2.1 MVSQueue Manager cannot be deleted because it is still active Queue Manager could not be deleted KMC0164W MQSeries Queue Manager is already running KMC0166S Failure occurred in the MQSeries Dspmqfls commandKMC0163E Your request to stop the Queue Manager failed KMC0174E An invalid MQSeries command argument was detected Appropriate MQSeries System Administration GuideKMC0172E An error occurred processing the Setmqaut command KMC0175S An unexpected error occurred on a Setmqaut command Setmqaut commandMore information Tandem NSK and AS/400, only one queue manager Command issued by the Configuration Agent failed If the problem persists, call Candle Customer SupportMVS only User Response Delete the defined storage class objects Communicate with the MQSeries command server MVS KMC0199E MQSeries object contains an invalid queue name @2 MQSeries channel name Can be used for naming all MQSeries objects is as follows KMC0204E Contents of the namelist are invalid Configuration User Response Correct the ’Through Queue Manager’ field SPX Names are restricted to a maximum of 8 characters in length Maximum of 12 characters in length Type Chltype of Rcvr For client connection channels to be used with OS/2 WarpObject, or the Appc side information data set Windowsnt Represents a Windows NT application User Response Specify a valid harden backout property @3 @4 That is defined with Usage Normal ManagerName of an Initiation queue Queue Usagexmitq That references the process on the Triggers settings Has triggering enabledEnabled Usage=Normal KMC0257W Connected Queue Manager @1 does not exist Usagenormal Æmvs Only on AIX Windows NT, and DOS it also applies to OS/390 for definingSupporting SPX Managers running on MVS Than or equal to zero, and less than or equal toKMC0287E Invalid maximum uncommitted messages value @2 For the Queue Manager Zero or greater than 999,999,999 999,999,999 Than or equal to zero, and less than or equal to 999,999,999 640,000 if the queue is on any other MQSeries platform Or channelManager. See the Maxmsgl parameter of the Alter Q KMC0312E Invalid autostart listener value KMC0314E Invalid Queue Manager autoconnect protocol @2 KMC0315E Invalid autostart channel initiator valueKMC0316E Invalid autoconnect prototype resource group @2 KMC0317E Invalid storage class name @2 KMC0322E Invalid Dead Letter Queue @2 KMC0321E Invalid authorization eventKMC0320E Invalid page set id @2 Is 1, and the maximum is Connected Queue Manager Clusters that the sender is associated with As a full repository for the clusterSender Cluster receiver channels that prevents duplicate names KMC0348E Invalid cluster name @2 KMC0349E Invalid cluster workload exit data @2 KMC0352E Invalid default bind KMC0350E Invalid maximum cluster workload data length @2KMC0351E Invalid cluster namelist @2 KMC0353E Invalid network priority @2 KMC0356W MQSecure command queue @1 not found KMC0357W MQSecure problem queue @1 not foundKMC0361E Invalid default protocol for managed cluster KMC0362E Invalid full repository setting Channels page in the cluster Queue Manager’s settings Have any defined connections to any full repositoriesAs 9,999 Conflicts KMC0372E Invalid backout threshold %s KMC0373E Invalid default priority %sMQSeries Version 2.1 for Windows KMC0377E Invalid service interval %s KMC0374E Invalid channel name %sKMC0375E Invalid maximum message length %s KMC0376E Invalid queue depth threshold %s KMC0382E Invalid configured system name %s KMC0380E Invalid retention interval %sKMC0381E Invalid storage class name %s Names are restricted to a maximum of 8 characters in length KMC0385E Invalid symbolic parameter list KMC0383E Invalid Queue Manager alias name %sKMC0384E Invalid prototype name %s That can be used for naming prototypes is as follows KMC0386E Invalid Queue Manager name %s KMC0387E Invalid trigger interval %sKMC0388E Invalid maximum open handles %s KMC0389E Invalid maximum uncommitted messages %s KMC0391E Invalid namelist name %s KMC0392E Invalid namelist KMC0393E Invalid process name %s KMC0394E Invalid batch size %sKMC0395E Invalid sequence number wrap %s KMC0396E Invalid trigger depth %s User Response Specify a valid name for the send exit KMC0412E Authorization events not allowed on this platform Events cannot be enabled for Queue Managers running on MVSMaximum of 8 characters in length To a maximum of 8 characters in length KMC0415E Mcatypethread not allowed on this platform KMC0416E Convertyes not allowed on this platformKMC0418E Triggers not allowed for this version of MQSeries KMC0419E Invalid primary log quantity %s KM2EXPFF-KMCRCA002I Managers running on MVS KMC0430E Invalid network priority %sKMC0431E Indextype %s invalid for this version of MQSeries Service for the Oamdb file Want to also disable connection authenticationKeyposition service for the Oamdb file Period . Forward slash / Underscore Percent sign % KMC0452E Invalid Qsgdisp value KMC0447E Invalid application type %sKMC0451E Invalid autostart trigger monitor value KMC0456E Invalid Cfstruct value @2 Order for you to specify a value other than Queue ManagerKMC0454E Invalid Clusdisp value Is 12 characters ListEntry Shared queue Candle WebSphere MQ Configuration Agent Starting Up Be interpretedKMCRCA002I Started System Action None User Response Parameter Error on Domain CALL. the Gate Being Called WAS call. the Parameter in Error WASSystem Action The error is propagated to the calling module KMQxx001E User’s Guide for MQSeries KMQCI107E Invalid Minor Command KMQCI110E Command not SupportedKMQCI108E KMQCI109E KMQCI116I Validate Command Completed Successfully KMQCI114E Unable to Load Domain Initialization ModuleKMQCI117E KMQCI118E List Operand Missing KMQCI123I Perform Startmon Command Processed Successfully KMQCI126I SET Group Command Processed SuccessfullyKMQCI122E Sample Interval Time Missing KMQCI124W Monitoring Already Active KMQCI130I SET Manager Command Processed Successfully KMQCI128E Name or Subsys Parameter RequiredKMQCI129E Inconsistent Parameters Specified for Status KMQCI131E Nickname Duplicates Existing Manager KMQCI134E Duplicate Manager for Statusadd KMQCI135E Manager not FoundKMQCI136E Channel not Found KMQCI137E Duplicate Channel KMQCI142I SET Channel Command Processed Successfully KMQCI143I SET Queue Command Processed SuccessfullyKMQCI144E Null Command Ignored KMQCI139E Duplicate Queue KMQCI149W Msgsecurity is Obsolete USE Msgaccess KMQCI146ETrace Head Node Initialization FAILED. RC=rc RSN=rs KMQCI147E KMQCI151I SET Rmanager Command Processed Successfully KMQCI150E Rmanager Name Cannot be GenericKMQCI152E Both Mgrname and Rmgrname Cannot be Specified KMQCI153W REMOTEQremotequeuename AGGRHISTaggregationsamples RETAINHISThistoricalaggregationvalue MSGACCESSparm ICYCLEintervalcycle HLQhighlevelqualifier MQ Manager managername in SETmanagernamemask is KMQCI309I KMQCI310IKMQCI311I KMQCI312I KMQCI318W KMQCI316IKMQCI317W Eventqueuein or eventqueueout Qmgrq Queuemanagereventqueue Perfmq performanceeventqueueChannelq channeleventqueue MGRNAMEqueuemanagernamemask STATISTICSlevel QMGRmgrname2 KMQCT129I KMQCT130IKMQDI101E KMQDU102I KMQIT103E KMQIT104I Omegamon for Websphere MQ Termination StartedKMQIT105I Omegamon for Websphere MQ Termination Complete KMQME102F Unable to Load Message Table Kmqamemt KMQMH102E KMQMH103EKMQMH104E Data Space Storage KMQMI101E KMQMI102EKMQMI103E KMQMI104I KMQMI108I Channel and Queue Masks Reset by Server KMQMI107IKMQMI109E KMQMI110E KMQMI112E Unable to Allocate Remote Queue KMQMI113EKMQMI114I KMQMI115E KMQMI116E MQ Manager Command Server not Responding KMQMI119I Error Validating REPLY-TO Queue ManagerKMQMI117I KMQMI118I KMQMI123E Correct Password has not Been Provided KMQMI122IKMQMI124E KMQMI125I KMQMI130E KMQMI131EKMQMI132E KMQMI133E KMQMI138E KMQMI139I Perform Startup is not SupportedKMQMI140I Perform Shutdown is not Supported KMQMI141E KMQMI146E KMQMI147EKMQMI148E Queue Ignored KMQMI153E KMQMI154EEXIST. SET Channel Ignored KMQMI155E KMQMI158E IgnoredKMQMI159E KMQMI160E There is no SET Manager command in the command file Monitor a non-default queue managerUser Response Add a Perform Startmon command to the command CCC for MQSeries to start monitoring KMQMI169E Environment Error Unable to Create Thread KMQMI170EKMQMI171I KMQMI172I KMQMI178E KMQMI174IKMQMI175E Abend in Processevent Intercepted KMQMI184E KMQMI180EKMQMI181E KMQMI185E LostKMQMI193E KMQMI194E KMQMI197I Mqseries Manager Command Server is Available KMQMI195EKMQMI196I KMQMI198I KMQMI201W Failed to Notify Offline Status KMQMI202IKMQMI203W KMQMI204W KMQMI208I Error LOG Monitoring Feature is Turned OFF KMQMI207WKMQMI209E Group Must Specify Single Queue Name Candle Products Messages Manual KLVHS-KONCT Error Installing SMF HOOK. RC=rc REASON=rs KMQMQ104EKMQMQ105E BAD Return Code from SERVER. RC=rc KMQMQ106E KMQMQ107EKMQMQ108E KMQMQ109I KMQMQ113E KMQMQ114IKMQMQ115E KMQMQ116E KMQMQ118E Unable to Obtain Common Storage for SRB Driver KMQMQ119ITermination KMQMQ120E KMQMQ124I KMQMQ140WKMQMQ141E KMQMQ142E KMQMQ143E KMQMQ150WOpen for Input by Another Application OPENINPUTCOUNT=X KMQMQ203E KMQMQ204ICompleted KMQMQ206E KMQMQ210E KMQMQ211EKMQMQ212W Result in Incomplete Application Queue Statistics KMQMQ217E KMQMQ218EKMQMQ219E KMQMQ220E KMQMQ224E MQ Commands Cannot be Executed for Remote Qmgrs KMQMQ223WStorage in Order to Maintain System Integrity KMQMQ225I KMQMQ229E KMQMQ232WKMQMQ233W Information Cannot be Collected SRBsrbname ABENDabendcode EPAentrypoint ADDRaddress KMQMQ242I QSG Monitor Disabled DUE to Zero Qsgchkinterval KMQMQ243IKMQMQ244I KMQMQ245I KMQMQ401E aaaaaaaa Cics release must be at least KMQMQ402E aaaaaaaa Unknown input methodKMQMQ403E aaaaaaaa No valid action specified KMQMQ404E aaaaaaaa No transaction ID specified for Kmqamqci KMQMQ408W aaaaaaaa CCC for MQSeries already active in Cics KMQMQ413I KMQMQ414WKMQPD101E KMQRM104E KMQTR103E BAD Return Code from NAME/TOKEN Services KMQTR104IKMQTR105E KMQTR106E KMQTR112I KMQTR113IKMQTR114I KMQTR115E Trace Buffer could not be Written KMQVS101E KMQVS102EKMQVS103E KMQVS104E KMQW008E Not Allowed by Msgaccess KMQW009E Agent Timeout OccurredKMQW000W KMQW001I MSG PUT on Xmit Q Successful KMQW010E Not Allowed by Command Option KMQW013I Command Accepted by MVSKMQW016E Syntax Error KMQW017E Command Failed KMQW018E Not Allowed by Security KMQW019E Not Supported by PlatformKMVCCC001E Unable to Locate Kmvccc Global Area KMVCCC002E Invalid Status Item Name in Getattribute Request KMVCCC008E Internal Thread Dispatch Error KMVCCC004EKMVCCC005E Enterprise Object not Found KMVCCC006E Enterprise Object is not Valid KMVCCC010E Unable to Initialize Kmvccc Service Queue KMVCCC013I Kmvccc Service Thread Shutting DownKMVCCC011E Unable to Initialize SDM Interface KMVCCC012I EIB Change Thread Shutting Down KMVCCC016E Unable to Initialize Situation Status Thread KMVCCC017E Unable to Attach Situation Status ThreadKMVCCC018E Unable to Initialize EIB Change Thread KMVCCC019E Unable to Attach EIB Change Thread Enabled KMVCCC024EKMVCCC025E KMVCCC026E KMVCCC036E Unable to Attach SDM Service Thread KMVCCC031I Kmvccc Support Initialization is CompleteKMVCCC032I Kmvccc Shutdown Complete KMVCCC033E KMVCCC038E KMVCCC039EKMVCCC040E KMVCCC041E Request, requestcode KMVCCC051E KMVCCC052EKMVCCC053E No Children Found for the Enterprise KMVCCC054E Abend Detected in Thread Routine KMVCCC058E KMVCCC059W Attribute Name Translation Cannot be PerformedKMVCCC060E KMVCCC100E Unable to Open Ddname Rkandatv Opendir KMVCCC103I KMVCCC104IKMVCCC105W KMVCCC106I KMVCCC108I KMVCCC109WKMVCCC110I KMVCCC111E Unable to Allocate Attribute Entry KMVCCC118E KMVCCC119EKMVCCC120W KMVCCC121E KMVCCC127E Unable to Allocate Command Node Entry KMVCCC125E Unable to Allocate Node StatusKMVCCC126E Unable to Allocate Attribute Enumeration KMVCCC128E Unable to Allocate Node List KMVCCC131E KMVCCC132EKMVCCC133E KMVCCC134E MODULEerrormodule RCreturncode SCsensecode User Response Check the Omegamon II for Vtam Configuration MODULEerrormodule RCreturncode SCsensecode Failed MODULEerrormodule RCreturncodeRCreturncode SCsensecode Unable to Freemain Userwork During Session Termination Trace Cleanup Detected AN Abend Condition AdditionalError Encountered During Trace Cleanup Error Encountered Removing Trace Facility During Session Termination MODULEerrormodule RCreturncodeKN3AF046 KN3AF047 User Session Terminated RCreturncode SCsensecode KN3AF052 Unable to Access Rkanpar MODULEerrormodule KN3AF054 Error When Reading membername MODULEerrormodule KN3AF056 Allocating Dataset dsname KN3AF057 Control Record GET Failed for DDNAMEddname KN3AF060 Vsam Logging Disabled MODULEerrormodule Reason KN3AF110 Dialogfunction Unable to Obtain Passed KN3AF111 Dialogfunction NON-ZERO Return Code from NDM CallKN3AF112 KN3AF114 Data not Available KN3AFNM1 Unable to Buildlocatemodify Npbnsb forNDM Control Module KN3AFNSB Load FAILED. NCP Statistics Each ACT Cycle Interval Manager NDM taskSystem Action NCP statistics information is not available From Resource Topology NCP Statistics Data Collection Disabled Message Type Internal or user errorCode NCP statistics data from the NCP data manager NDM GENDATEgenerationdate GENTIMEgenerationtime Failed Request Failed for RESOURCEresourcename NPALUnpalunameGENDATEgenerationdate GENTIMEgenerationtime NCP Topology Genlevel Mismatch for KN3AF134 NCP Topology not CREATED. will Retry Next ACT CycleInterval KN3AF136 KN3AXNPB Addnpb Function Failed RCreturncode NDM ACT Resource Cleanup in Progress NDM ACT Resource Cleanup CompleteCleanup Requested NDM Task has Recycled Since Last INTERVAL. Resource KN3AF147 KN3AFNMI NCP Data Manager Task not InstalledKN3AF146 Message Type KN3AF149 KN3AF150KN3AF151 SMF Response Time Recording for NCP Resources is Inactive REASONreasoncode Topology Update Functions Initialization FailedNPALUnpaluname Failed RCreturncode KN3AF157 Topology Upate Functions Module KN3AFNUT Load FailedNCP Statistics Data not Available KN3AF161 MODULEmodule NON-ZERO Return Code from TCP/IP Call PSW=programstatusword, ROUTINE=programname Rregisternumber Rregisternumber registervalue TCP/IP Collector MIB Browser Memory Allocation Failed INFOinformationcode TCP/IP Service Thread MIB Browser Xmcs Snmp Manager has TerminatedSnmp Manager Request Timed OUT Initialization Complete TCP/IP Service Thread MIB Browser Xmcs Abended TCP/IP Service Thread MIB Browser Xmcs is TerminatingTCP/IP Service Thread MIB Browser Xmcs Completed Reason reasoncode TCP/IP functionname FAILED. ERRNO=errorcode KN3CT125 KN3CT131 MIB Browser Initialization Failed RCretcodeKN3CT132 MIB Browser is not Active RC=retcode MODULEmodule KN3CT201 KN3CT201 module Unable to Load Module module KN3CT205 KN3AITXB Required Parameter not Supplied for KN3CT208 KN3AITXB Ezasmi Gethostname Failure KN3CT209 KN3AITXB Invalid Return Code from KN3APTXEKN3APTXE KN3CT302 KN3AITDE Required SUB-ELEMENT Parameter Vtam Command Error Find Requires StringCharacter String not Found Locate Requires String Sampling Interval WAS TOO LONG, TRY Again Must be NumericInvalid Selection User Commands Updated Collection Interval Timeout Data ReinitializedType a / Next to the Desired Selections Selection not Available Variable Named varname Contains contentsofvarname Request Successful Dialog ErrorInvalid Command Threshold Criteria Updated Select the Actions PULL-DOWN MenuResources Added Field is Required Global Options Updated Threshold Update FailedGlobal Options Update Failed Invalid Numeric Range ETE Interface Disabled Operand for the Autorefresh Command Must be onOFF, or a Numeric Value from 10-3600 Seconds Must be in the Range of 15-360 Minutes SAS Clist WAS not Entered in the Correct Format Please USE the Following FormatCANDLE.ON.V500.SASCNTLKN3CLST6 SAS Clist Dataset Name Specified Cannot be Located Monitoring Started Monitoring StoppedMonitoring Thresholds Changed Monitoring Thresholds Deleted Monitor Options Update Error Monitor Options UpdatedTerminal Options Updated Autorefresh Options Updated SMF Definition Added SMF Definition ChangedSMF Definition Deleted Response Time Must be Greater then Previous Range AT Least 1 Administrator is Required Not Allowed to Delete the only AdministratorUser Authority Changed User Authority Deleted Navigation not Allowed NEW Rachsrt Parameter is not PrimeLight PEN is not Supported Trace Already Active or Completed GET Failed for Default Printer Options Trace is not ActiveClose Failed for Sysout Dataset No Screen Prints Were Requested Allocate Failed for Sysout Dataset ADD Failed for Screen Print LOGOpen Failed for Sysout Dataset PUT Failed for Sysout Dataset Printer Options Updated ERROR, see ViewlogTrace ABENDED, Data Still Good LU not Found Following Error Occurred When Omegamon Attempted To Access the Specified SAS Print Options LIBRARY. ReturnTREND/EXCEPTION LOG File Access Error ETE Started Task is not Available Options Pulldown Panel are not VALID. Please Update Historical Graph Options Before Attempting to AccessAN Unexpected Error Occurred Requested PIU WAS not Found Enter YES or no Enter C or WEnter a Numeric Value or Leave Blank Critical Must be Greater than Warning Domain Categories Selection is only Valid for the IO00 BufferPool Enter N or S View Command Invalid When Displaying DirectoryAlphanumeric Field Required Control Block Cannot be Accessed for ONE AN Attempt to Access the Address Space FailedFollowing Reasons Control Block is no Longer Valid Tuning Statistics are not Active Unable to Find the Actual RPL. the Crpl is DisplayedINSTEAD. Most of the Data from the Original RPL can be Found in the Crpl Trace not Started Not Valid for GROUPS. USE List L and Select AN IndividualResource Resource not Found Specify Either Resource Name or Network Address RPL Data is only Available for Applid ResourcesResource has no Sessions Vtam Replaceable Constants Module Istracon is not Storage Required for Modelling not AVAILABLE. Ensure That LIMIT23,X is Coded for the Startup ParameterEnter N, L, P, or U Enter M or C Enter P or U Resources Must be the Same TypeSelect only ONE Resource with Mark Select only ONE Resource with Copy Resource has no Subordinate Resources Resource has Already Been StartedResource has NPACOLL=NO and Cannot be Monitored Resource is not Active to Vtam and Cannot be Monitored Monitor Options will be Updated with the Current Site DefaultsResource Already Using Site Default Options No Exceptions are Generated for this Field Resource Must be AN LU or Terminal No Subordinate Resources are Being MonitoredResources Already Added Resource Must be Stopped Before Monitoring Options can No Update AUTHORIZATION, View only Group Description Already ExistsSubordinate Resources Must be Stopped Before this Resource can be Stopped Resources has Been Disabled NCP Trend Recording Disabled AT StartupNCP Topology Update Interval Must be Greater than Enter M or H Update Successful Invalid Scroll AmountNo LUS Associated with Resource Address Space Name Already Exists Update Error Must be AlphabeticBuffer Pool Data not Available Connection Number Required for Drop TCP/IP Command Error AT Least ONE Entry is RequiredOID Name is Unknown OID Number is Unknown KN3FCCMD Command Processing Complete HI Priority Connection not Defined Fpon Component Functions Installation Failed KN3AYFCV not AVAILABLE. Install Option RequiredFpon Component Functions Installation Complete Fpct Component Functions Installation Complete Fpct Component Functions Installation FailedSevt Vtam Environment Installation Complete Sevt Vtam Environment Installation Failed Semv MVS Environment Installation Complete Semv MVS Environment Installation FailedSevt Vtam Environment Status Failed ROUTINE=KN3AHEV3 Semv Vtam Environment Status Failed ROUTINE=KN3AHEM3 REASON=reasoncode RETURN=returncode Message Type User error KN3FC055Ndmt NCP Data Manager Task Start Failed ROUTINE=KN3AHNT1 REASON=reasoncode RETURN=returncode Status text Dbug Extended Diagnostics Mode Status Failed Tcpc TCP/IP Collector Installation Failed Tcpc TCP/IP Collector Start Failed ROUTINE=KN3ACTC1 Tcpc TCP/IP Collector Stop Failed ROUTINE=KN3ACTC2 Tcpc Status Command Failed ROUTINE=KN3ACTC3 KN3FC096 FTP Initialization Failed to Load KN3INFT2 Initializing FTP Reporting ThreadFTP Initialization Complete Error Freeing CSA Override Value AcceptedCSA Monitor Ended Bytes CSA Error Loading Llllll Increase Bufmax AND/OR Reduce CollectintervalNo Jobname Found CSA Freed Error Freeing CSA Error RE-LOADING LlllllError Obtaining CSA Recovering from Already Added Exit Error Freeing CSA Copy of Record Adding SMF ExitsAdded SMF Exits Deleting SMF Exits Initializing Cleanup Thread Table Cleanup RunningNo Unprocessed SMF Records Omegamon FTP Agent Resource Manager Entered Error no Eyecatcher in CSA Resource Manager StartedInvalid ROW Pointer IRA Subnode Registration Thread is Active Tcpncpvtam Monitor Subnode Registered for Originnode Tcpncpvtam Monitor Subnode Deregistered for KN3IR904 Pthreaddetach error KN3IR905 IRA Manager command unknownKN3IR906 IRA Manager command operand missing KN3IR908 IRASubnodeRegister error RC=xx Node=ccccccccccccc IRA Subnode Registration Thread Currently Active IRA Subnode Registration Thread is not ActiveIRA Subnode Registration Thread is not Responding KN3IR919 TCP Monitor Start Failed for Originnode originnode KN3IR916 $SCAN Error Parsing cccccccc ROUTINE=ccccccccR0=hhhhhhhh R1=hhhhhhhh ROUTINE=routine KN3IR926 TCP Monitor Collection Failed MACROcccccccc macro KN3IR922 TCP Monitor Stop Failed for Originnode originnodeKN3IR924 IRA Subnode Deregistration Failed ROUTINE=cccccccc Terminate KN3LC102 Appc Request Error appcrequest ROUTINE=routinenameKN3LC101 Collector Applid applid UNAVAILABLE, NDM Task will KN3LC107 SQL Request ERROR, ROUTINE=routine-name KN3LC109 KN3AYNCE Select Count Error ROUTINE=routinenameKN3LC104 Missing KN3AYLCA Work Area ROUTINE=routinename KN3LC108 Failure to Acquire Storage for storagearea KN3LC110 Appc Client Services Abend CODE=abendcode PSW=psw KN3LC111KN3LC112 Connection Failure Acbname localid KN3LS101 RETURN=returncode REASON=reasoncode ROUTINE=routinename RETURN=returncode REASON=reasoncode KN3LS110 Invalid Resource Count Error ROUTINE=routinename KN3LS111 KN3AYWKG Chain Error ROUTINE=routinenameKN3LS112 Lucs Services Abend CODE=abendcode PSW=psw KN3LS114 Connection Failure Using Acbname applid NCP Statistics Collector Available for Requests NCP Statistics Collector is Terminating Npaluname REASON=reasoncode Load Failed KN3ND015 $PAM$PAMname Failed ROUTINE=KN3AHN04 DDNAME=KN3RRT R15=registervalue Resourcename NPALU=npalunameR1=returncode R15=returncode R0=returncode R1=returncode MEMBER=membername R15=registervalue R0=registervalue R1=registervalueRRTname Ddname KN3RRT During functioncall. Found Label NCPsourcelabel Network Topology Error in Locate Function DuringTopology for Deletion Is not Specified Current TopologyNCP will not be Monitored NCP Data Manager Task Available for Requests NCP Data Manager Task is Terminating PSW=programstatusword ROUTINE=routinenameNCP Data Manager Task Termination Complete NCP Data Manager Task Initialization Failed SENSE=sensecode RETURN=returncodeKN3ND108 SQL Resource Allocation Failed RETURN=returncode SENSE=sensecode KN3AYNCE Allocation Failed KN3AYNRE RDS Segment Allocation FailedKN3AYNRE Header Allocation Failed KN3ND130 KN3AGNPB Service Function ABENDED, CODE=abendcode NCP data manager task request failsResourcename failed System Action The NCP data manager task request fails Ndmt Service Request Failed KN3AGNPB Entered for AN Invalid FunctionKN3AGNPB no Hash Table Address Found in the ACT Work Area OWNER=ownername,RETURN=hexreturncode KN3AGFPF Floating Point Function Failed REASON=ABENDCODE=abendcode Genpunam Errors Detected Genlunam Errors DetectedErrors Detected During X.25 Resource Scanning for KN3AGNTS Labeltypetab ACT Started Successfully Appc Environment not InitializedAppc Environment Termination Failed RCreturncode Omegamon II for Vtam V500 Initialization ErrorETE Connected Successfully KN3PN008 Logon Error Encountered for User userid Function KN3PN012 Table Service Error in Dialog callingdialogUSERWORKuserworkareaaddress textstring KN3PN011 KN3PN015 Engine Services Error in Dialog callingdialog KN3PN016 Error in Dialog errordialog LUluname APPLapplidKN3PN017 V500 Product Conversion Complete Authorization Failed Omegamon II for Vtam V500 Initialization Failure APFOmegamon II for Vtam V500 Initialization Failure Invalid Vtam Level Detected NCP Global Options Table Conversion Complete Security EnabledOmegamon II for Vtam V500 Initialization Failure Security Enabled SESSIONSDMsessionname SDMAPPLSDMapplidSYSTERMSDMluname REFRESHSDMrefreshinterval TRIGGERSDMhotkey KN3SD003 Enhanced Original Zoom ActivatedKO41031 Situation &1 is true Severity System Programmer ResponseNo KO41039 Error in request &1. Status &2. Reason &3 KO41034 Monitoring for situation &1 endedSeverity KO41035 Object &1 changed by &2 KO41042 is written to the log Be numeric User Response Change the compare value & 2 to a numeric Another KO48071 Policy &1 activated KO48010 Policy &1 startedBefore it finishes running KO48078 Policy &1 updated by &2 KO48079 Activity &1 in policy &2 updated by &3KO48080 Ranking group &1 updated by &2 KO48073 Policy &2, activity &1 has started User KO48090 Policy &1 has deactivated. Restart limit exceeded KO48091 Changing priority for job &1 job number &2 to &3KO48092 Changing job queue for job &1 job number &2 to &3 KO48093 Changing time slice for job &1 job number &2 to &3 KO48106 Ending job &1 job number &2 KO48110 Policy &2, activity &3 Evaluating situation &1KO48112 Holding job &1 job number &2 KO48119 Releasing job &1 job number &2 KO48152 Situation &1 could not find message queue &2 KO48148 Policy &2, activity &3 Waiting for &1 secondsKO48150 Policy &2, activity &3 Running policy &1 KO49019 Candle Management Server CMS log not displayed KO49016 Situation &1 imbedded in policy &2. Not deletedKO49017 Policy &1 imbedded in policy &2. Not deleted Severity System Programmer ResponseNo Be used Candle Management Server CMS again Severity System Programmer ResponseImmediate KO4SRV001 KO4SRV002KO4SRV003 KO4SRV004 KO4SRV005 KO4SRV006KO4SRV007 KO4SRV008 KO4SRV018 KO4SRV019KO4SRV020 KO4SRV021 KO4SRV030 KO4SRV031KO4SRV032 KO4SRV033 KO4SRV039 KO4SRV040KO4SRV041 KO4SRV042 KO4SRV049 KO4SRV050KO4SRV051 KO4SRV052 KO4SRV054 KO4SRV055KO4SRV056 KO4SRV057 KO4SRV061 KO4SRV062KO4SRV063 KO4SRV064 KO4SRV068 KO4SRV069KO4SRV070 KO4SRV071 KO4SRV074 KO4SRV075KO4SRV076 KO4SRV077 KO4SRV080 KO4SRV081KO4SRV082 KO4SRV083 KO4SRV089 KO4SRV090KO4SRV091 KO4SRV092 KO4SRV096 KO4SRV097KO4SRV098 KO4SRV099 KO4SRV103 KO4SRV104KO4SRV105 KO4SRV106 KOCJO001 Initialize Completed Normally KOCJO002 Interface Shutdown RequestedKOCJO003 Interface Shutdown Completed KOCJO004 Interface Suspend Requested KOCJO012 Journal Number Error KOCJO008 Unable to Determine Start TypeKOCJO009 KOCPLT00 not LOCATED. Check Linkedit KOCJO010 Failure in Cics Inquire KOCJO016 Journal Open Error KOCJO018 Exit Enable ErrorKOCJO019 Exit Extract Error KOCJO014 Suspend Transaction Inactive KOCJO024 Exit Disable Failure KOCJO020 Getmain FailureKOCJO021 Exit Start Failure KOCJO022 Exit Stop Failure KOCJO026 Transaction Start Failure KOCJO027 Interface InactiveKOCJO028 Initialize is Already in Process KOCJO029 Resume is Already in Process KOCJO033 Error Occurred During Cleanup Disable KOCJO034 Error Occurred During Cleanup FreemainKOCJO037 Error Received During Wait Processing KOCJO032 Unknown Function in Process KOCJO038 Error Received During Freemain Processing KOCJO039 Journal Write FailureKOCJO040 Interface Transaction has Abended KOCJO041 Rtype not Present in Dictionary KOCJO046 Omegbsc not Present in Dictionary KOCJO044 Netname not Present in DictionaryKOCJO045 Uowid not Present in Dictionary Candle Products Messages Manual KLVHS-KONCT KOGCM001 KOGCM002KOGCM003 KOGCM004 KOGCM005 KOGDF005KOGDF006 KOGDF007 KOGEC002 Specified Session not Defined to Povi KOGEC001 No Session SpecifiedSessid omitted KOGEC003 KOGEC004KOGEC005 KOGEC006 KOGEC008 KOGEC009KOGEC010 KOGEC011 KOGEC013 KOGEC014KOGEC015 KOGEC016 KOGEC018 KOGER001 Invalid Selection CodeKOGER002 KOGEV001 KOGEV004 KOGEV005KOGEX001 KOGIN001 KOGLM003 KOGLM004KOGLM005 KOGMM001 KOGOP000 KOGOP001KOGOP002 KOGOP004 KOGOP005 KOGOP006KOGRT006 KOGRT009 KOGRU002 KOGRU003KOGRU004 KOGRU005 KOGRU017 Testing PATH, PF12 Pressed KOGRU012KOGRU013 KOGRU014 KOGRU018 KOGRU019KOGRU020 KOGST001 KOGTB001 KOGTB002KOGTB003 KOGTB004 KOGTB007 KOGTB009KOGUT001 KOGUT002 KOGUT005 KOGUT006KOGUT007 KOGUT009 KOGUT012 KOGVL00IKOGVL02I KOGVL03S KOGVL05S Unable to Determine SLU Applid KOGVL06S Unable to Locate VU Server IPC QueueKOGVL07S KOGVL08E KOGVL10I KOGVL11SKOGVL12S KOGVL13E KOGVL14I Outbound LU0 Packet KOGVL15IKOGVL16E KOGVL20I KOGVL21I KOGVL22IKOGVL23I KOGVL24I KOGVL25E KOGVL26EKOGVL27E KOGVL29E KOGVL30E Unable to Terminate lrtype STATUS=statusKOGVL31E BAD pdutype CONTINUATION. SEQNO=seqno EXPECTED=eseqno KOGVL33I KOGVL34IKOGVL35I KOGVL36I KOGVL38E KOGVL40EKOGVL41E KOGVL99I KOGVS001 KOGVS002KOGVS003 KOGVS004 KOGVS01E KOGVS02EKOGVS03E KOGVS04I KOGVS05E KOGVS06EKOGVS10E KOGVS11I VU Server Shutdown in Progress KOGVS13I KOGVS20EKOGVS90S VU Server Initialization Failed KOGVS99I VU Server is Terminating Vupl TYPE=vupltype Contents KOGVT10EUnable to Locate Parameters LRN=lrn KOGVT14I KOGVT17W KOGVT18IKOGVT19I KOGVT20I KOGVT22E KOGVT23WKOGVT24E KOGVT25I KOGVT26I KOGVT27IKOGVT28E KOGVT29E KOGVT31I KOGVT32EKOGVT33E KOGVT34E KOGVT34I KOGVT35EKOGVT36E KOGVT37E KOGVT38E KOGVT40IKOGVT99I VU Thread is Terminating KONAF001 KONAF003 Background ETE Collector Terminated with Error KONAF004 ACT Terminated AbnormallyManager NDM functions module failed KONAF006 Member Koncnmap Contains Invalid ACB Name MODULEerrormodule RCreturncode KONAF041 KONAF021KONAF031 KONAF045 KONAF044 Error Encountered During Trace CleanupCapture Reader Codes MODULEerrormodule RCreturncode KONAF046 Error Encountered Removing Trace Facility During KONAF047KONAF048 KONAF050 KONAF051 KONAF052KONAF053 KONAF054 KONAF056 KONAF057KONAF058 KONAF059 KONAF062 KONAF060KONAF061 KONAF110 KONAF111KONAF112 KONAF113 KONAF115 KONAFNM1 Unable to Locate Site Monitor Table tablenameKONAF116 KONAFNM1 Unable to Buildlocatemodify Npbnsb for KONAF117 KONAF120 KONAF121KONAF122 KONAF123 KONAF127 NCP Statistics Data Collection Disabled KONAF125KONAF126 KONAF128 KONAF130 KONAF131KONAF132 KONAF133 NCP Topology Genlevel Mismatch for KONAF135 KONAF136Konaxnpb Addnpb Function Failed RCreturncode KONAF137 KONAF140 NDM ACT Resource Cleanup in Progress KONAF141 NDM ACT Resource Cleanup CompleteKONAF138 Konaxnpb Gethash Function Failed RCreturncode KONAF146 Konafnmi NCP Data Manager Task not Installed KONAF144KONAF145 KONAF147 KONAF148 KONAF149From the Konaxcrb macro KONAF150 KONAF154 Topology Update Functions Initialization Failed KONAF153KONAF155 KONAF156 KONAF158 KONAF159KONAF160 KONAF161 KONCT001 $INIT Failed for Main Thread LRN KONCT002KONCT003 KONCT004 TCP/IP Statistics Collector is Terminating KONCT010 KONCT011KONCT012 KONCT013 KONCT015 KONCT050 Snmp Manager has TerminatedKONCT051 KONCT052 KONCT102 TCP/IP Service Thread MIB Browser Xmcs Abended Support Services. See message KONCT103 which followsKONCT103 KONCT110 KONCT112 $GMEM Failed for Command Output Record KONCT113 $GMEM Failed for Command Param StructureKONCT121 TCP/IP Address Space Collector Failed KONCT122 KONCT125 KONCT131KONCT132 KONCT201 KONCT202 KONCT203KONCT204 KONCT206 KONCT208 KonaptxeKONCT210 KONCT301 KONCT303 KONCT303 Konaitdd Invalid Element Parameter parm Candle Products Messages Manual KLVHS-KONCT

VALID RANGE IS 10–3600

THE CONTROL BLOCK CANNOT BE ACCESSED FOR ONE OF THE

FOLLOWING REASONS:

1. THE CONTROL BLOCK IS NO LONGER VALID.

2. AN ATTEMPT TO ACCESS THE ADDRESS SPACE FAILED

THE ADDRESS SPACE HAS TERMINATED

THE ADDRESS SPACE IS BEING SWAPPED IN, TRY AGAIN LATER

THERE WAS NO RPL CONTROL BLOCK FOUND FOR THIS SESSION

UNABLE TO DISPLAY THE CONTROL BLOCK DATA. CHECK THE

MESSAGE LOG FOR MORE INFORMATION

356 Candle Products Messages Manual (KLVHS–KONCT)

GC32-9172-00 specifications