50RLP Aquazone™ System Control Panel Water Source Heat Pump Units
Installation Instructions
CONTENTS
Page
SAFETY CONSIDERATIONS. . . . . . . . . . . . . . . . . . . . . . . 1
GENERAL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1,2
Aquazone System Control Panel Functionality . . . . . .2
CCN Systems Using PremierLink™ Controls . . . . . . . .2
COMPONENTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Aquazone System Control Panel Hardware . . . . . . . . . .2
Water Source Heat Pumps with
PremierLink Controller Hardware. . . . . . . . . . . . . . . . . .7
Field-Supplied Hardware
for
Install Loop Water Supply and Return
Temperature Sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
Install Loop Water Pressure Sensor . . . . . . . . . . . . . . . .13 Install Loop Water Flow Switch . . . . . . . . . . . . . . . . . . . . .13 Connect to CCN Communication Bus . . . . . . . . . . . . . .14
Set the Aquazone System Control Panel
Controller Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Log Off from Controller. . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 LID Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 Sequence of Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
•HEAT REJECTION
•HEAT ADDITION
•WATER CIRCULATION
CONFIGURATION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Hardware Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Software Points . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Loop Supply Water Set Point . . . . . . . . . . . . . . . . . . . . . . .24
System Pressure Set Point . . . . . . . . . . . . . . . . . . . . . . . . .24
Global Dictionary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Heat Pump Default Configuration. . . . . . . . . . . . . . . . . . .26
Cool Source Default Configuration . . . . . . . . . . . . . . . . .26
Heat Source Default Configuration . . . . . . . . . . . . . . . . .26
Occupancy Configuration Screen . . . . . . . . . . . . . . . . . .26
Network Time Schedule . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Holiday Schedules. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
IMPORTANT: Read the entire instruction manual before starting installation.
SAFETY CONSIDERATIONS
Installation and servicing of
Untrained personnel can perform basic maintenance functions. All other operations should be performed by trained service personnel. When working on
Improper installation, adjustment, alteration, service, main- tenance, or use can cause explosion, fire, electrical shock or other conditions which may cause personal injury or property damage. Consult a qualified installer, service agency, or your distributor or branch for information or assistance. The quali- fied installer or agency must use
Follow all safety codes. Wear safety glasses and work gloves. Use quenching cloth for brazing operations. Have fire extinguisher available. Read these instructions thoroughly and follow all warnings or cautions attached to the unit. Consult local building codes and the National Electrical Code (NEC) for special installation requirements.
Understand the signal words — DANGER, WARNING, and CAUTION. DANGER identifies the most serious hazards which will result in severe personal injury or death. WARNING signifies hazards that could result in personal injury or death. CAUTION is used to identify unsafe practices, which would result in minor personal injury or product and property damage.
Recognize safety information. This is the
Electrical shock can cause personal injury or death. Before installing or servicing system, always turn off main power to system. There may be more than one disconnect switch. Turn off accessory heater power if applicable.
GENERAL
IMPORTANT: The installation of water source heat pump units and all associated components, parts, and accessories which make up the installation shall be in accordance with the regulations of ALL authorities having jurisdiction and MUST conform to all applicable codes. It is the responsi- bility of the installing contractor to determine and comply with ALL applicable codes and regulations.
Manufacturer reserves the right to discontinue, or change at any time, specifications or designs without notice and without incurring obligations.
Book | 1 | 4 | PC 111 | Catalog No. | Printed in U.S.A. | Form | Pg 1 | Replaces: New | |
Tab | 5a | 5a |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|