PUMP 2 RUN TIME — This point displays the number of hours that the pump has run. When the maximum number of hours is exceeded (9999 hours), both pumps run time hours will reset to 0.
Pump 2 Run Time |
|
Display Units | Numeric |
Default Value | 0 |
Display Range | 0 to 9999 |
Network Access | Read/Write |
Loop Supply Water Set Point — The low set point is the low limit the supply water temperature may drop down to before the heat source will be activated to maintain the Loop Supply water temperature. The high set point is the high limit the supply water may rise to before the cooling source will be activated to maintain the loop supply water temperature. See Table 15. Set points can also be modified with slide bars in the ComfortVIEW™ software. See Fig. 11.
Table 15 — Loop Supply Water (SETPT01)
DESCRIPTION |
| VALUE | NAME |
Occupied Lo Setpoint |
| 60.00 df | OccLow |
Occupied Hi Setpoint |
| 90.00 df | OccHgh |
Unoccupied Lo Setpoint |
| 60.00 df | UnOccLow |
Unoccupied Hi Setpoint |
| 90.00 df | UnOccHgh |
Occupied Low: |
|
| |
Configuration Units | degrees F (degrees C) | ||
Configuration Range | |||
Default Value | 60.0 |
| |
Occupied High: |
|
| |
Configuration Units | degrees F (degrees C) | ||
Configuration Range | |||
Default Value | 90.0 |
| |
Unoccupied Low: |
|
| |
Configuration Units | degrees F (degrees C) | ||
Configuration Range | |||
Default Value | 60.0 |
| |
Unoccupied High: |
|
| |
Configuration Units | degrees F (degrees C) | ||
Configuration Range | |||
Default Value | 90.0 |
| |
System Pressure Set Point — This set point defines the system pressure that the variable speed pumps will operate when the Aquazone™ system control panel is configured for variable speed pumping. See Table 16. Set points can also be modified with slide bars in the ComfortVIEW software. See Fig. 12.
Table 16 — System Pressure (SETPT02)
DESCRIPTION | VALUE | NAME |
Occupied Lo Setpoint | 10.00 PSIG | OccLow |
Occupied Hi Setpoint | 10.00 PSIG | OccHgh |
Unoccupied Lo Setpoint | 10.00 PSIG | UnOccLow |
Unoccupied Hi Setpoint | 10.00 PSIG | UnOccHgh |
Occupied Low: |
|
Configuration Units | PSIG |
Configuration Range | |
Default Value | 10.0 |
Occupied High: |
|
| |
Configuration Units | PSIG |
| |
Configuration Range | |||
Default Value | 10.0 |
| |
Unoccupied Low: |
|
| |
Configuration Units | PSIG |
| |
Configuration Range | |||
Default Value | 10.0 |
| |
Unoccupied High: |
|
| |
Configuration Units | PSIG |
| |
Configuration Range | |||
Default Value | 10.0 |
| |
Global Dictionary — The | Global Dictionary table is | ||
shown in Table 17. |
|
| |
Table 17 — Global Dictionary (AQUAMASC) | |||
|
|
| |
DESCRIPTION |
| VALUE | NAME |
PUMPS 0=ON/OFF,1=VFD |
| 0.00 | PUMP_CFG |
Pump Rotation Hours |
| 50.00 | ROT_TIME |
TOWERS 0=STAGED,1=VFD |
| 0.00 | COOL_CFG |
HEAT 0=STAGED,1=MOD/VFD |
| 0.00 | HEAT_CFG |
Sched Bcst 0=N,1=Y |
| 0.00 | GLOBAL |
PUMP CONTROL TYPE — This configuration determines how the pump outputs will be controlled. If the pump relays were ordered with the Aquazone system control panel, then the pump control type should be set to 0. If the pump outputs will control variable speed pumps, then the configuration should be set to 1. When variable speed control is selected, both outputs will control simultaneously.
Pump Control Type: |
|
Configuration Units | None |
Configuration Range | 0 or 1 |
Default Value | 0 |
PUMP ROTATION HOURS — When the pump control type is set to 0 (on/off), this configuration is used to set the maxi- mum number of hours the lead pump may accumulate beyond the numbers of hours accumulated for the lag pump. When this difference in hours is reached, the lead pump will change to the pump with the lesser number of accumulated run hours.
Pump Rotation Hours: |
|
Configuration Units | HOURS |
Configuration Range | 0 to 9999 |
Default Value | 50.0 |
TOWER/COOLING SOURCE CONTROL TYPE — This configuration determines how the tower outputs will be con- trolled. If panels were ordered with the stage output transducers, then tower control type should be set to 0. If the tower outputs will control variable speed tower fans, then the configuration should be set to 1.
Variable speed configuration will control both outputs si- multaneously.
Tower/Cooling Source Control Type:
Configuration Units | None |
Configuration Range | 0 or 1 |
Default Value | 0 |
24
