DSP Algorithm List

00 :Auto Pan

•Function

Continually performs left-right panning of the input signal in accordance with an LFO.

•Parameters

0 : Rate (Range: 0 to 127) Adjusts the panning rate.

1 : Depth (Range: 0 to 127) Adjusts the panning depth.

01:Tremolo

•Function

Adjusts volume of input signal in accordance with an LFO.

•Parameters

0 : Rate (Range: 0 to 127) Adjusts the tremolo rate.

1 : Depth (Range: 0 to 127)

Adjusts the tremolo depth.

02:2BandEQ

•Function

This is a two-band equalizer.

•Parameters

0 : Low Frequency (Range: 0 (200Hz), 1 (400Hz), 2 (800Hz)) Adjusts the cutoff frequency of the low-band equalizer.

1 : Low Gain (Range: –12, –11, –10 to 0 to +10, +11, +12)

Adjusts the gain of the low-band equalizer.

2 : High Frequency (Range: 0 (6.0KHz), 1 (8.0KHz), 2 (10KHz)) Adjusts the cutoff frequency of the high-band equalizer.

3 : High Gain (Range: –12, –11, –10 to 0 to +10, +11, +12) Adjusts the gain of the high-band equalizer.

03:3BandEQ

•Function

This is a three-band equalizer.

•Parameters

0 : Low Frequency (Range: 0 (200Hz), 1 (400Hz), 2 (800Hz)) Adjusts the cutoff frequency of the low-band equalizer.

1:Low Gain (Range: –12, –11, –10 to 0 to +10, +11, +12) Adjusts the gain of the low-band equalizer.

2:Mid Frequency (Range: 0 (1.0KHz), 1 (1.3KHz), 2 (1.6KHz), 3 (2.0KHz), 4 (3.0KHz), 5 (4.0KHz), 6 (6.0KHz), 7 (8.0KHz)) Adjusts the center frequency of the mid-band equalizer.

3:Mid Gain (Range: –12, –11, –10 to 0 to +10, +11, +12) Adjusts the gain of the mid-band equalizer.

4:High Frequency (Range: 0 (6.0KHz), 1 (8.0KHz), 2 (10KHz)) Adjusts the cutoff frequency of the high-band equalizer.

5:High Gain (Range: –12, –11, –10 to 0 to +10, +11, +12) Adjusts the gain of the high-band equalizer.

04:LFO Wah

•Function

This is a “wah” effect that can automatically affect the frequency in accordance with an LFO.

•Parameters

0:Input Level (Range: 0 to 127)

Adjusts the input level. The input signal can become distorted when the level of the sound being input, the number of chords, or the Resonance value is large. Adjust this parameter to eliminate such distortion.

1:Resonance (Range: 0 to 127) Adjusts the resonance of the sound.

2:Manual (Range: 0 to 127)

Adjusts the frequency used as the basis for the wah filter.

3:LFO Rate (Range: 0 to 127) Adjusts the rate of the LFO.

4:LFO Depth (Range: 0 to 127) Adjusts the depth of the LFO.

05:Auto Wah

•Function

This is a “wah” effect that can automatically affect the frequency in accordance with the level of the input signal.

•Parameters

0:Input Level (Range: 0 to 127)

Adjusts the input level. The input signal can become distorted when the level of the sound being input, the number of chords, or the Resonance value is large. Adjust this parameter to eliminate such distortion.

1:Resonance (Range: 0 to 127) Adjusts the resonance of the sound.

2:Manual (Range: 0 to 127)

Adjusts the frequency used as the basis for the wah filter.

3:Depth(Range: –64 to 0 to +63)

Adjusts the depth of the wah in accordance with the level of the input signal.

Setting a positive value causes the wah filter to open in direct proportion with the size of the input signal, producing a bright sound.

Setting a negative value causes the Wah filter to close in accordance with the size of the input signal, which produces a dark tone quality. However, large input re-opens the Wah filter, even if it is closed.

06:Compressor

•Function

Compresses the input signal, which can have the effect of suppressing level variation and making it possible to sustain dampened sounds longer.

•Parameters

0:Depth (Range: 0 to 127)

Adjusts compression of the audio signal.

1:Attack (Range: 0 to 127)

Adjusts the attack amount of the input signal.

A smaller value causes prompt compressor operation, which suppresses the attack of the input signal.

A larger values delays compressor operation, which causes attack to be output as-is.

2:Release (Range: 0 to 127)

Adjusts the time from the point when the input signal drops below a certain level until the compression operation is stopped. When an attack feeling is desired (no compression at the onset of the sound), set this parameter to as low a value as possible.

To have compression applied at all times, set a high value.

3:Level (Range: 0 to 127) Adjusts the output level.

The output volume changes in accordance with the Depth setting and the characteristics of the input tone. Use this parameter to correct for such changes.

07:Limiter

•Function

This is an effector that you can use to set an upper limit value on the level of the input signal.

•Parameters

0:Limit (Range: 0 to 127)

Adjusts the volume level from which the limit is applied.

1:Attack (Range: 0 to 127)

Adjusts the attack amount of the input signal.

2:Release (Range: 0 to 127)

Adjusts the time from when the input signal drops below a certain level until the limit operation stops.

3:Level (Range: 0 to 127) Adjusts the level being output.

The output volume changes in accordance with the Limit setting and the characteristics of the input tone. Use this parameter to correct for such changes.

08:Distortion

•Function

This effect provides Distortion + AmpSimulator.

•Parameters

0 : Gain (Range: 0 to 127) Adjusts the input gain.

707A-E-085A

E-83