Manuals / Brands / Baby / Safety Gate / Chamberlain / Baby / Safety Gate

Chamberlain GA400D, GA420D 11Reattach Motor Assembly, Attach Operator to Gate and Bracket, For Model GA420D Only, Warning Sign Placement, PATH, GATE TRAVEL, Inside Property

1 48

Download 48 pages, 10.2 Mb

11Reattach Motor Assembly

Slide motor assembly onto arm and secure with screws (4). NOTE: Turn operator over to re-install screws. Attach arm cover.

If installing a second gate operator repeat steps 1-12.

NOTE: The arm brackets must be reversed or mirrored on the second operator.

“THIS SIDE TO GATE” label MUST face the gate.

GATETO SIDETHIS

NOTE: Motor housing screws must

Screws be fully tightened with screw heads recessed below housing surface.

Arm Cover

Motor

Arm

Attach Operator to Gate and Bracket

12 Make sure “THIS SIDE TO GATE” label faces the gate when reattaching operator to gate. Tighten all bracket connections.

For Model GA420D Only

13 Repeat Steps 1-12 for second operator.

Warning Sign Placement

14 Warning placards MUST be installed on both sides of the gate and in plain view. Fasten to gate with cable ties.

Gate Post

Fence

Gate

GATE TRAVELPATH

WARNING

To prevent SERIOUS INJURY or DEATH from a moving gate:

•Install warning signs on the front and back of the gate in PLAIN VIEW.

•Permanently secure each warning sign in a suitable manner using fastening holes.

Moving Gate Can Cause

Injury or Death

KEEP CLEAR! Gate may move at any time without prior warning.

Do not let children operate the gate or play in the gate area.

This entrance is for vehicles only Pedestrians must use separate entrance

Inside Property

Installation

20

Contents

■Please read this manual and the enclosed safety materials carefully ■Periodic checks of the operator are required to ensure safe operation ■The model number label is located inside the control box of your operator ■Serial # ■Installation Date 2-7INTRODUCTION 8-12PREPARATION AND OVERVIEW 13-22INSTALLATION 23-31WIRING 32-35PROGRAMMING Operator Specifications Main Supply (Motor) Accessory Power NOTE: Power Consumption Safety Installation Information Page Carton Inventory pulls-to-open pushed open Hardware Inventory All Models: GA420D Only: SAFETY SENSORS HARDWARE CONDUIT PREPARATION AND OVERVIEW Left-HandGate Right-HandGate Inside Gate Dual Gate Overview Check Your Gate Pull-to-Open Push-to-Open Left-HandHinge Mounted Right-HandHinge Mounted INSTALLATION Identify Hinge Type 2 Measuring and Marking for the Gate Bracket Template Method Tape Measure Method Position the Extension Bracket to Post Bracket 4Remove Motor Assembly 5Determine Maximum Piston Travel 6 Attach Brackets to Gate Operator 7Position Gate Bracket 8 Check Piston Travel 9 Secure Gate Bracket to Gate Secure Post Bracket to Gate Post 11Reattach Motor Assembly Attach Operator to Gate and Bracket For Model GA420D Only Warning Sign Placement Open the Control Box Remove the Control Board Select Mounting Holes Mount the Control Box Install the Control Board WIRING 1Watertight Connector Nut 2 Insert Operator Cable 3 Connect Operator to Control Board Connect Gate Operator (Gate 2) to Control Box (Model GA420D Only) Set the Lock/Bipart Delay LOCK/BIPART DELAY Outside Property 1Connect second Operator to Control Board (Model Ga420D Only) 2 Junction Box 3 Connect Watertight Connectors Connect Wires in Junction Box 5 Secure Junction Box Connect Indoor Transformer to Low Voltage Wire and Battery 1 Connect indoor Transformer to Control Board AC PWR/SOLAR DIAGNOSTIC STOP 2 Connect Batteries PROGRAMMING Single Arm Left-HandSide Program Open Program Close Dual Gate (Right-SidePrimary Operator) Force Adjustment Party Mode Timer-to-Close(TTC) To Add or Reprogram a Remote Control (not provided) LEARN XMITTER To Add a Wireless Keyless Entry (not provided) To Erase All Codes OPERATION AND MAINTENANCE Release Engage Wiring Diagram Diagnostic Chart FLASH Power ON FLASHES STOP not connected Troubleshooting SYMPTOM POSSIBLE SOLUTION Page Page Control Box Gate Operator Arm Accessories 953D 916GA 915GA 917GA WARRANTY POLICY CHAMBERLAIN ONE YEAR LIMITED WARRANTY NOTES TEMPLATE FOR POST BRACKET MOUNTING