Manuals / Brands / Baby / Safety Gate / Chamberlain / Baby / Safety Gate

Chamberlain GA400D, GA420D 3 Connect Operator to Control Board, GATE, If installing one operator, proceed to page, If installing two operators, continue to the next page

1 48

Download 48 pages, 10.2 Mb

3 Connect Operator to Control Board

Extend operator cable and wires to GATE 1 connector and connect as shown. Tighten watertight connector nut.

	NC
			NO
			C
	Z1		NO
	Z1		C
		10A 32V	NC	ON	OFF	Terminal blocks
		10A 32V		MAGLOCK		Terminal blocks
	GATE 1		BRN			can be removed
	GATE 1		YEL			can be removed
			GRN
Brown			WHT
Brown			BLU		LEARN	to simplify wiring.
					LIMITS	to simplify wiring.
					GATE 1
	BRN		RED
	BRN
Green		D1Ø			GATE 2
Green		D1Ø	24V	FORCE	CLOSE
	GRN				TIMER TO
	GRN		GRN
			BRN
White			WHT
White			BLU		OFF MAX	COM
	WHT		YEL		OFF MAX	COM
	WHT		RED
Yellow	YEL		MAX			COM
	YEL
Blue	BLU
	BLU
Red	RED
	RED

Z12

CONTROL BOX

ACCESSORYR9Ø

POWER

Operator Cable

Watertight Connector Nut

				e
			Can	Caus
	ving	Gate	Death
Mo	ving	y or
Mo	Injur

Operator Cable

If installing one operator, proceed to page 29.If installing two operators, continue to the next page.

Wiring

Contents

■Please read this manual and the enclosed safety materials carefully ■Periodic checks of the operator are required to ensure safe operation ■The model number label is located inside the control box of your operator ■Serial # ■Installation Date 2-7INTRODUCTION 8-12PREPARATION AND OVERVIEW 13-22INSTALLATION 23-31WIRING 32-35PROGRAMMING Operator Specifications Main Supply (Motor) Accessory Power NOTE: Power Consumption Safety Installation Information Page Carton Inventory pulls-to-open pushed open Hardware Inventory All Models: GA420D Only: SAFETY SENSORS HARDWARE CONDUIT PREPARATION AND OVERVIEW Left-HandGate Right-HandGate Inside Gate Dual Gate Overview Check Your Gate Pull-to-Open Push-to-Open Left-HandHinge Mounted Right-HandHinge Mounted INSTALLATION Identify Hinge Type 2 Measuring and Marking for the Gate Bracket Template Method Tape Measure Method Position the Extension Bracket to Post Bracket 4Remove Motor Assembly 5Determine Maximum Piston Travel 6 Attach Brackets to Gate Operator 7Position Gate Bracket 8 Check Piston Travel 9 Secure Gate Bracket to Gate Secure Post Bracket to Gate Post 11Reattach Motor Assembly Attach Operator to Gate and Bracket For Model GA420D Only Warning Sign Placement Open the Control Box Remove the Control Board Select Mounting Holes Mount the Control Box Install the Control Board WIRING 1Watertight Connector Nut 2 Insert Operator Cable 3 Connect Operator to Control Board Connect Gate Operator (Gate 2) to Control Box (Model GA420D Only) Set the Lock/Bipart Delay LOCK/BIPART DELAY Outside Property 1Connect second Operator to Control Board (Model Ga420D Only) 2 Junction Box 3 Connect Watertight Connectors Connect Wires in Junction Box 5 Secure Junction Box Connect Indoor Transformer to Low Voltage Wire and Battery 1 Connect indoor Transformer to Control Board AC PWR/SOLAR DIAGNOSTIC STOP 2 Connect Batteries PROGRAMMING Single Arm Left-HandSide Program Open Program Close Dual Gate (Right-SidePrimary Operator) Force Adjustment Party Mode Timer-to-Close(TTC) To Add or Reprogram a Remote Control (not provided) LEARN XMITTER To Add a Wireless Keyless Entry (not provided) To Erase All Codes OPERATION AND MAINTENANCE Release Engage Wiring Diagram Diagnostic Chart FLASH Power ON FLASHES STOP not connected Troubleshooting SYMPTOM POSSIBLE SOLUTION Page Page Control Box Gate Operator Arm Accessories 953D 916GA 915GA 917GA WARRANTY POLICY CHAMBERLAIN ONE YEAR LIMITED WARRANTY NOTES TEMPLATE FOR POST BRACKET MOUNTING