Manuals / Brands / Baby / Safety Gate / Chamberlain / Baby / Safety Gate

Chamberlain GA400D, GA420D WIRING, 1Watertight Connector Nut, 2 Insert Operator Cable, Connect Gate Operator (Gate 1) to Control Box

1 48

Download 48 pages, 10.2 Mb

WIRING

WARNING

To reduce the risk of SEVERE INJURY or DEATH:	• DO NOT install ANY wiring or attempt to run the operator
• ANY maintenance to the operator or in the area near the	without consulting the wiring diagram. We recommend that
operator MUST not be performed until disconnecting the	you install an optional reversing edge BEFORE proceeding
electrical power and locking-out the power via the operator	with the control station installation.
power switch. Upon completion of maintenance the area	• ALL power wiring should be on a dedicated circuit and well
MUST be cleared and secured, at that time the unit may be	protected. The location of the power disconnect should be
returned to service.	visible and clearly labeled.
• Disconnect power at the fuse box BEFORE proceeding.	• ALL power and control wiring MUST be run in separate
Operator MUST be properly grounded and connected in	conduit.
accordance with local electrical codes. NOTE: The operator	• BEFORE installing power wiring or control stations be sure to
should be on a separate fused line with a 15 amp	follow ALL specifications and warnings described below.
circuit breaker.	Failure to do so may result in SEVERE INJURY to persons
• ALL electrical connections MUST be made by a qualified	and/or damage to operator.
individual.

Connect Gate Operator (Gate 1) to Control Box

1Watertight Connector Nut

Insert operator cable through watertight connector nut.

Watertight Connector Nut

Operator

Cable

2 Insert Operator Cable

Insert watertight connector into the bottom of the control box and tighten with nut. Insert operator cable through watertight connector mounted in the bottom of the control box.

Nut

Watertight Connector

18

30

30

Control Box

Watertight

ConnectorOperator

Cable

Watertight

Connector Nut

	Can	Cause
ng	Gateor Death
MoviInjury

23

Wiring

Contents

■Please read this manual and the enclosed safety materials carefully ■Periodic checks of the operator are required to ensure safe operation ■The model number label is located inside the control box of your operator ■Serial # ■Installation Date 2-7INTRODUCTION 8-12PREPARATION AND OVERVIEW 13-22INSTALLATION 23-31WIRING 32-35PROGRAMMING Operator Specifications Main Supply (Motor) Accessory Power NOTE: Power Consumption Safety Installation Information Page Carton Inventory pulls-to-open pushed open Hardware Inventory All Models: GA420D Only: SAFETY SENSORS HARDWARE CONDUIT PREPARATION AND OVERVIEW Left-HandGate Right-HandGate Inside Gate Dual Gate Overview Check Your Gate Pull-to-Open Push-to-Open Left-HandHinge Mounted Right-HandHinge Mounted INSTALLATION Identify Hinge Type 2 Measuring and Marking for the Gate Bracket Template Method Tape Measure Method Position the Extension Bracket to Post Bracket 4Remove Motor Assembly 5Determine Maximum Piston Travel 6 Attach Brackets to Gate Operator 7Position Gate Bracket 8 Check Piston Travel 9 Secure Gate Bracket to Gate Secure Post Bracket to Gate Post 11Reattach Motor Assembly Attach Operator to Gate and Bracket For Model GA420D Only Warning Sign Placement Open the Control Box Remove the Control Board Select Mounting Holes Mount the Control Box Install the Control Board WIRING 1Watertight Connector Nut 2 Insert Operator Cable 3 Connect Operator to Control Board Connect Gate Operator (Gate 2) to Control Box (Model GA420D Only) Set the Lock/Bipart Delay LOCK/BIPART DELAY Outside Property 1Connect second Operator to Control Board (Model Ga420D Only) 2 Junction Box 3 Connect Watertight Connectors Connect Wires in Junction Box 5 Secure Junction Box Connect Indoor Transformer to Low Voltage Wire and Battery 1 Connect indoor Transformer to Control Board AC PWR/SOLAR DIAGNOSTIC STOP 2 Connect Batteries PROGRAMMING Single Arm Left-HandSide Program Open Program Close Dual Gate (Right-SidePrimary Operator) Force Adjustment Party Mode Timer-to-Close(TTC) To Add or Reprogram a Remote Control (not provided) LEARN XMITTER To Add a Wireless Keyless Entry (not provided) To Erase All Codes OPERATION AND MAINTENANCE Release Engage Wiring Diagram Diagnostic Chart FLASH Power ON FLASHES STOP not connected Troubleshooting SYMPTOM POSSIBLE SOLUTION Page Page Control Box Gate Operator Arm Accessories 953D 916GA 915GA 917GA WARRANTY POLICY CHAMBERLAIN ONE YEAR LIMITED WARRANTY NOTES TEMPLATE FOR POST BRACKET MOUNTING