Manuals / Brands / Baby / Safety Gate / Chamberlain / Baby / Safety Gate

Chamberlain GA400D, GA420D Operator Specifications, NOTE:, Travel Time, Temperature, Accessory Power, Power Consumption, Main Supply (Motor), Maximum Gate Length, Maximum Gate Weight

1 48

Download 48 pages, 10.2 Mb

Operator Specifications

Main Supply (Motor)	12Vdc Battery run. Operational between 11.5Vdc and 14.5Vdc.
Accessory Power	12V nominal Class II battery voltage source is limited to:
	• Solar or AC Cable up to 50' - 500 mA
	• AC Cable 50' up to 250' - 250mA
	• AC Cable 250' up to 1000' - 100mA
	NOTE: Increased accessory power drawn from the operator will shorten the
	battery life.
Power Consumption	30 Watts max (during battery charging)
Battery Charger Supply	14.5Vac nominal, 30 VA max.
Maximum Gate Length	18 ft. at 350 lbs.
Maximum Gate Weight	850 lbs. at 6 ft.
Travel Time	20 seconds (typical)
Temperature	-20ºC to +50ºC, -4ºF to 122ºF Contact Technical Support for applications
	below -20ºC
Protection Fuse Battery 1	ATC 20A
Protection Fuse Battery 2	ATC 20A

3	Introduction

Contents

■Please read this manual and the enclosed safety materials carefully ■Periodic checks of the operator are required to ensure safe operation ■The model number label is located inside the control box of your operator ■Serial # ■Installation Date 2-7INTRODUCTION 8-12PREPARATION AND OVERVIEW 13-22INSTALLATION 23-31WIRING 32-35PROGRAMMING Operator Specifications Main Supply (Motor) Accessory Power NOTE: Power Consumption Safety Installation Information Page Carton Inventory pulls-to-open pushed open Hardware Inventory All Models: GA420D Only: SAFETY SENSORS HARDWARE CONDUIT PREPARATION AND OVERVIEW Left-HandGate Right-HandGate Inside Gate Dual Gate Overview Check Your Gate Pull-to-Open Push-to-Open Left-HandHinge Mounted Right-HandHinge Mounted INSTALLATION Identify Hinge Type 2 Measuring and Marking for the Gate Bracket Template Method Tape Measure Method Position the Extension Bracket to Post Bracket 4Remove Motor Assembly 5Determine Maximum Piston Travel 6 Attach Brackets to Gate Operator 7Position Gate Bracket 8 Check Piston Travel 9 Secure Gate Bracket to Gate Secure Post Bracket to Gate Post 11Reattach Motor Assembly Attach Operator to Gate and Bracket For Model GA420D Only Warning Sign Placement Open the Control Box Remove the Control Board Select Mounting Holes Mount the Control Box Install the Control Board WIRING 1Watertight Connector Nut 2 Insert Operator Cable 3 Connect Operator to Control Board Connect Gate Operator (Gate 2) to Control Box (Model GA420D Only) Set the Lock/Bipart Delay LOCK/BIPART DELAY Outside Property 1Connect second Operator to Control Board (Model Ga420D Only) 2 Junction Box 3 Connect Watertight Connectors Connect Wires in Junction Box 5 Secure Junction Box Connect Indoor Transformer to Low Voltage Wire and Battery 1 Connect indoor Transformer to Control Board AC PWR/SOLAR DIAGNOSTIC STOP 2 Connect Batteries PROGRAMMING Single Arm Left-HandSide Program Open Program Close Dual Gate (Right-SidePrimary Operator) Force Adjustment Party Mode Timer-to-Close(TTC) To Add or Reprogram a Remote Control (not provided) LEARN XMITTER To Add a Wireless Keyless Entry (not provided) To Erase All Codes OPERATION AND MAINTENANCE Release Engage Wiring Diagram Diagnostic Chart FLASH Power ON FLASHES STOP not connected Troubleshooting SYMPTOM POSSIBLE SOLUTION Page Page Control Box Gate Operator Arm Accessories 953D 916GA 915GA 917GA WARRANTY POLICY CHAMBERLAIN ONE YEAR LIMITED WARRANTY NOTES TEMPLATE FOR POST BRACKET MOUNTING