Manuals / Char-Broil / Kitchen Appliance / Convection Oven

Char-Broil 463269411 manual Lower back panel Inside, Light wire harness Adapter wire harness

Models: 463269411

1 36

Page 26

This step requires two people to lift and position grill head onto cart. Carefully lower the grill head onto the cart, aligning slots at bottom of grill head with posts on cart side panels. Make sure the regulator hose is hanging inside the cart. Grill head must face open side of cart.

Grill head

Regulator hose

Connect Adapter wire harness and Light wire harness.

Light wire harness

Adapter wire harness

Lower back panel (Inside)

Adapter

Page 26

Image 26

Char-Broil 463269411 manual Lower back panel Inside, Connect Adapter wire harness and Light wire harness

Contents

Serial Number Estimated assembly time 30-40 minutesPlease call Date PurchasedSafety Symbols INSTALLER/ASSEMBLERTABLE OF CONTENTS DANGERWash your hands after handling this product Installation Safety PrecautionsCALIFORNIA PROPOSITION LP Cylinder Removal, Transport and Storage USE AND CARENever fill a cylinder beyond 80% full LP Liquefied Petroleum GasLP Cylinder Exchange Leak test new and exchanged LP cylinders BEFORE connecting to grillFor your safety LP Cylinder Leak TestLeak Testing Valves, Hose and Regulator Outdoor gas appliance is not intended to be installed in or on a boatOutdoor gas appliance is not intended to be installed in or on an RV Do not use grill until leak-testedDo not let children operate or play near grill Safety TipsFor Safe Use of Your Grill and to Avoid Serious Injury Do not block holes in sides or back of grillIgnitor Lighting continued Turn controls and gas source or tank OFF when not in useGeneral Grill Cleaning Match-LightingVERY IMPORTANT Burner tubes must reengage valve Cleaning the Burner AssemblyStoring Your Grill 1. Turn gas OFF at control knobs and LP cylinder3. Turn the light switch to “ON” Bulb ReplacementBulb Specification ˙ Keep any electrical supply cord away from any heated surfaceDo not plug this appliance into an indoor circuit Cleaning the LensDo not use this appliance if the circuit does not have GFI protection PERIOD OF COVERAGE LIMITED WARRANTYSCOPE OF COVERAGE TYPE OF FAILURE COVERAGEDescription PARTS LISTDescription NOT PicturedA MMM C B OOO PARTS DIAGRAM GJ J J I I I D K K K K X E U U U ULocking caster Fixed caster ASSEMBLY OF LEFT CARTFront Bottom shelf1/4-20x1/2” screw 7mm lock washer 1/4-20x1/2” screwInside shelf NOTE MAKE SURE THAT THE FRONT BRACE IS MOUNTED AS ILLUSTRATED BELOW#10-24x3/8” screw Shelf bracketpanel Back panel1/4-20x1/2” 7mm lock screw washer Drawer front panel Drawer frameDrawer frame #10-24x3/8” ScrewLocking caster Fixed caster ASSEMBLY OF RIGHT CARTFront Bottom shelf1/4-20x1/2” screw 7mm lock washer Left side panel NOTE MAKE SURE THAT THE FRONT BRACE IS MOUNTED AS ILLUSTRATED BELOWTop shelf Swing panel 7mm lock washer 1/4-20x1/2” screw 5mm LockFront door panel Back panelAttach side panels to bottom shelf using three ASSEMBLY OF MIDDLE CARTRear FrontTemperature gauge Temperature gauge stem Control panel Back of the panelLower back panel Inside Connect Adapter wire harness and Light wire harnessAdapter Light wire harness Adapter wire harnesstwo #8x3/8” self-tapping screws on each side Secure using two #8x3/8” self-tapping screws each sideInsert front brace under control panel and between cart side panels Upper back panelself-tapping screw Front bracePage flare-up emitters must be placedkeeping both flat walls Note Some parts omitted forHeat diffuser clarity of illustrationCylinder screw at rear of cart during use, transport, and storageGrease tray Always keep LP cylinders in upright positionProblem TroubleshootingPrevention/Solution GAS ISSUESPrevention/Solution Troubleshooting continuedProblem AUTO-CLEANCheck Procedure Troubleshooting - Electronic IgnitionProblem Ignition Prevention/SolutionWarranty Registration Department P.O. Box Columbus, GA