Programming Manual

FuzzyScan

Configure Your FuzzyScan

Operation Control

♦ Operation Mode Setting ♦

 

PROGRAM

 

 

 

 

 

 

F_DEFAULT

 

 

 

 

 

 

 

 

 

 

Family Code Selection

P.C

 

Parameter Selection

Option Code

 

Operation Mode

SS

Low Power mode

 

 

Force mode

0

 

5

 

 

Trigger mode ￿

 

 

 

 

 

 

 

 

SS

 

 

Toggle mode

1

 

6

 

 

SS

Presentation mode

 

 

Diagnostic mode

2

 

7

 

 

SS

Alternative mode

 

 

Level mode

3

 

8

 

 

SS

Flash mode

 

 

L680/L780 laser imagers don’t support:

4

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Flash/ Force/ Toggle/ Diagnostic mode.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Presentation Control

SS

Presentation mode ￿

 

 

 

 

0

 

 

 

 

 

 

 

 

 

 

 

SS

Flash mode

 

 

 

 

1

 

 

SS

Force mode

 

 

 

 

2

L680/L780 laser imagers don’t support this function.

￿Low Power Mode (Low Power Triggering) The scanner goes into idle state after scanning the bar code. You must press the trigger to wake up the scanner for operation. It is very helpful for mobile data collection and application, which are concerned with power saving.

￿Trigger Mode (External Triggering) The scanner goes into standby state after scanning the bar code. You must press the trigger to turn on the light source of the scanner before scanning the bar code.

￿Presentation Mode (Auto Detection) Presentation mode uses ambient light to detect the bar codes. The light source is off until the scanner detects an image which is similar to a barcode. Then the light source turns on automatically to read the bar code. If the light level in the room is not high enough, Presentation Mode may not work properly. You can choose different level of “Presentation Sensitivity” to meet your application (Please refer to the setting of “Presentation Sensitivity”).

￿Alternative Mode (Periodic Power Off) The scanner keeps the light source of the scanner turned on till the pre-defined light source on time is up. After the scanner turns off the light source, you must press the trigger to turn on the light source again. After each good read, the timer counter of “Light Source on Time” is reset. You do not have to press the trigger frequently, it is very convenient for multiple scanning.

￿Flash Mode (Pulse Driven Reading) The scanner flashes the light source of the scanner without using the trigger. If the scanner detects an image which is similar to a bar code, the scanner forces on the light source automatically and scans the bar code. Flash Duty Cycle adjustment can change the frequency of the blinking.

￿Force Mode (Continued Power On) The light source of the scanner is forced on for continued operation without pressing the trigger switch. This mode is convenient for high speed bar code reading.

￿Toggle Mode (Repeat Reading) The toggle mode is very similar to the Alternative Mode but without the pre-defined light source on time concern. You must press the trigger to turn on the light source of the scanner to scan. The scanner keeps the light source turned on until you press the trigger again.

￿Diagnostic Mode (Test Reading) This operation mode is specifically designed for diagnostic purposes. When this operation mode is selected, the light source of the scanner is force on without regard for other programmable parameters, such as reread delay, redundancy, and so forth.

￿Level Mode (Auto Power Off) When this operation mode is selected, the scanner continues to turn on the light source of the scanner before a good read or pre-defined “Light Source on Time”. If the scanner decodes a bar code successfully, it turns off the light source immediately. After the scanner turns off the light source, you must press the trigger to turn on the light source again. If there is no scanning operation performed during the pre-defined light source on time, the scanner enters the idle state after the pre-defined light source on time is up.

￿Presentation Control When the scanner is placed on SmartStand, the scanner will be switched from hand-held scanning to hands free scanning automatically. Three hands scanning modes are available. You are recommended to use flash mode or force mode while under insufficient ambient light.

￿Only Low power mode, Trigger mode, Presentation mode and Level mode are available for FuzzyScan Laser model.

39