Programming Manual

FuzzyScan

Configure Your FuzzyScan

Condensed DataWizard

♦ Data Verifier Setting ♦

PROGRAM

 

 

 

 

 

 

 

 

F_DEFAULT

 

 

 

 

 

 

 

 

 

 

 

Family Code Selection

P.C

 

Parameter Selection

 

Option Code

2nd Option Code
Verifier Control

SS

 

Disable ￿

 

FIN

 

 

 

 

MS

 

Select one bar code symbology

 

(2 digits)

 

automatic termination

 

 

 

 

 

 

 

 

 

 

 

 

 

MS

 

Select all bar code symbologies

00

 

 

automatic termination

 

 

 

 

 

 

 

 

 

 

 

Identified Data Length

SS

 

Disable ￿

 

FIN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DS

 

Enable

 

(2 digits)

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Determine the identified data length for verification.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

1st Identified Character

SS

 

Disable ￿

 

FIN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DS

 

Enable

 

(2 digits)

 

[00-7F]

 

 

 

 

 

 

 

 

 

 

 

 

 

2-digits checking position; 1 identified character

 

 

position

 

 

 

 

 

 

 

 

 

 

 

 

 

2nd Identified Character

SS

 

Disable ￿

 

FIN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DS

 

Enable

 

(2 digits)

 

[00-7F]

 

 

 

 

 

 

 

 

 

 

 

 

2-digits checking position; 1 identified character

 

 

position

 

 

 

 

 

 

 

 

 

 

 

 

 

3rd Identified Character

SS

 

Disable ￿

 

FIN

 

 

 

 

 

 

 

 

 

 

 

 

 

 

DS

 

Enable

 

(2 digits)

 

[00-7F]

 

 

 

 

 

 

 

 

 

 

 

 

2-digits checking position; 1 identified character

 

 

position

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

￿The Data Verifier is used to provide advanced verification for error-free scanning and to work as an Embedded Data Transmitting Filter.

￿All data must conform to the Identified Bar Code Symbologies, Identified Data Length, and one to three Identified Characters in the checking position. Otherwise, the FuzzyScan will not transmit the data to the host computers or terminals, but will instead issue 3 long beeps for verification error and skip the scanned data.

￿The Data Verifier checks only scanned data without Preamble, Postamble, STX, ETX, Data Length, Prefix/Suffix Symbology ID or Record Suffix.

￿Regarding the “Bar Code Selection” and “Position Calculation” of Data Verifier, please refer to page 45 for details.

￿Please note that all “Character” input should be referred to the ASCII/HEX Table listed in Appendix to find matched HEX value.

48